View Single Post
  #9   Report Post  
Old June 27th 05, 08:20 PM
Purr Plexed
 
Posts: n/a
Default


I fixed it! A previous owner made a wiring mistake when he/she
installed the 6 kHz AM filter. There are two yellow wires that
connect to the mode wafer switch. One of them is for the AM filter.
The other yellow wire turns the CW side tone oscillator on when the
rig is in CW mode. A previous owner wired both yellow wires to the AM
tab on the mode switch. All is well now, and it works as it should.

Thnx.

-Purr Plexed no more...


On Sat, 18 Jun 2005 16:32:52 -0400, Casual Fool
wrote:

On Fri, 17 Jun 2005 23:13:18 GMT, (Purr Plexed)
wrote:


I purchased a used Yaesu FT-101ee off of Ebay. When I transmit
with either a CW stright key or the microphone on AM the CW sidetone
comes out of the ft-101e speaker. Keying the CW key in CW mode does
not transmit. Whas there a mod for a Yaesu FT-101e that turned AM
mode in to sort of a code practice oscillator?

KS4HY


Hi Purr Plexed,
No, there wasn't a code practice mod for the
FT-101, however, there was a mod that allowed you to install an AM
filter in the CW slot, and its tricky to do if your not familiar with
close space soldering, and part identification. First, take a look at
your Crystal Filter Board, and see if there are two filters on the
board. If there are, remove the FT-101 case, and take a look to see if
someone has installed an AM filter. The AM filter would installed in
the CW socket if its there. I have seen alot of problems such as yours
from people not doing the mod correctly. If you do have an AM filter
installed, the first thing to do is pull the board, and look at the
back of the board. The board is in a plugin slot, and not hard to get
out, just eyeball it, you'll see how to take it out.. If you see two
.01 ceramic caps between the SSB and AM filter, remove them. It
doesn't tell you this in the service manual, but you must do this.
Now, here is the rest of the CORRECT way to check the mod to see if it
was done right

AM MOD FROM YAESU SERVICE MANUAL

Install AM Filter in the CW filter position. Wire mode switch S2C
as follows:

1. Remove the jumper between pins 1 and 5

2. Remove the banded end of diode D1 from pin 5 and solder it to pin 4

3. Solder a jumper from pin 3 to pin 2

4. Remove the yellow wire at pin 9 of MJ-3 which goes to the heater
switch SSB and solder it to pin 4 of S2C

5. Remove the yellow wire from pin 4 of S2C and solder it to pin 5 of
S2C

6. Remove the red wire from pin 1 of S2C and solder it to pin 1 of
mike connector J3* - SPECIAL NOTE.. I have done quite a few
of these mods, and have found that on some Yaesu sets, the
mike connector is not wired the same. The red wire should go to
the GROUND lug of the mike connector.

This completes the AM filter modification. The set will operate
normal in the LSB and USB modes, and will use the SSB filter in the CW
mode. The wide band AM filter will be switched into the circuit when
the mode switch is placed in the AM position and the SSB filter will
be switched out of the circuit. The only change from normal operation
will be in the TUNE-CW modes. The mike pre-amp and amplifier stages
will be turned on if the VOX switch is in the VOX position. Audio
cannot be transmitted in the CW mode even though the VOX relay can be
energized via the mike, but in the tune mode audio can be transmitted
if the mike gain is turned up.

I also presume you checked both relays and assured none of the
points are stuck or dirty or sequence incorrectly. OH, BTW, BEFORE YOU
PULL THE RELAY from the PA cage, MARK IT, as it only goes in one way,
and there are NO GUIDE PINS TO LET YOU KNOW HOW TO PUT IT BACK IN, and
it will plug in either way.. Oh, and not only mark the plastic cover,
once you take off the plastic cover, mark the relay itself, as you
could also plug the plastic cover on backwards. Plug it in wrong, and
the instant you turn the set on, you'll let the smoke out of your set.

In closing, I have scanned the whole Yaesu Service Manual into a .PDF
(21 megs plus) document, and as soon as I can get over to a friends
house with a fast connection I will up the manual to http//mods.dk
... BTW, all of the above material is provided for REFRENCE ONLY. If
you choose to use any of it, you do so at your own risk. I take no
responsibility if you blow your radio up.. Best 73 es gud luck OM..
Anthony, WB8MLA