Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Old March 8th 06, 08:10 PM posted to rec.radio.shortwave
Slow Code
 
Posts: n/a
Default Why Antenna Tuners Aren't Necessarily Useful for Shortwave Listening - Question Shortwave Listening (SWL) Antenna Tuners - Do You Have An Opinion ?

"RHF" wrote in
ups.com:

For One and All,

QUESTION - Shortwave Listening (SWL) Antenna Tuners
- - - Do You Have An Opinion ? - - -

Why Antenna Tuners Aren't Necessarily Useful for Shortwave Listening
http://www.nyx.net/~dgrunber/tuner.ssi
- - - by - - - Daniel A. Grunberg

Here is "Dan Grunberg's Home Page"
http://www.nyx.net/~dgrunber/

Welcome - Here are some of my documents that may interest you.

TOPIC - SHORTWAVE RADIO :

* Advice to Shortwave Newbies
(Useful sources of information and useful links)

* Minimal Antennas and Grounds
(Why they may be all you need)

* So You're Certain You Need an Outdoor Antenna
(With a link to a reasonable design)

* Why Antenna Tuners Aren't Necessarily Useful
for Shortwave Listening
(This article could save you some money)

* A Rambling Review of the Lowe HF-150
(A nice receiver)

* Nifty 48-Inch (122-cm) Whip Antenna
with a PL-259 Connector

* The Sony 7600G and Its Synchronous Detector
(Why sync detectors are worth having)

* Analog vs. Digital Receivers (an introduction)

* Preventing Wire Antennas from Breaking in the Wind


and that's Today's On-Topic Post - iane ~ RHF
.
.
. .



Nice on-topic post. A tuner isn't really necessary for impedance matching,
but it can act as a pre-selector if your receiver has a poor front end in it.
Which can help improve things in some situations.

SC
  #2   Report Post  
Old March 8th 06, 09:59 PM posted to rec.radio.shortwave
Telamon
 
Posts: n/a
Default Why Antenna Tuners Aren't Necessarily Useful for Shortwave Listening - Question Shortwave Listening (SWL) Antenna Tuners - Do You Have An Opinion ?

In article et,
Slow Code wrote:

"RHF" wrote in
ups.com:

For One and All,

QUESTION - Shortwave Listening (SWL) Antenna Tuners
- - - Do You Have An Opinion ? - - -

Why Antenna Tuners Aren't Necessarily Useful for Shortwave Listening
http://www.nyx.net/~dgrunber/tuner.ssi
- - - by - - - Daniel A. Grunberg

Here is "Dan Grunberg's Home Page"
http://www.nyx.net/~dgrunber/

Welcome - Here are some of my documents that may interest you.

TOPIC - SHORTWAVE RADIO :

* Advice to Shortwave Newbies
(Useful sources of information and useful links)

* Minimal Antennas and Grounds
(Why they may be all you need)

* So You're Certain You Need an Outdoor Antenna
(With a link to a reasonable design)

* Why Antenna Tuners Aren't Necessarily Useful
for Shortwave Listening
(This article could save you some money)

* A Rambling Review of the Lowe HF-150
(A nice receiver)

* Nifty 48-Inch (122-cm) Whip Antenna
with a PL-259 Connector

* The Sony 7600G and Its Synchronous Detector
(Why sync detectors are worth having)

* Analog vs. Digital Receivers (an introduction)

* Preventing Wire Antennas from Breaking in the Wind


and that's Today's On-Topic Post - iane ~ RHF
.
.
. .



Nice on-topic post. A tuner isn't really necessary for impedance matching,
but it can act as a pre-selector if your receiver has a poor front end in it.
Which can help improve things in some situations.


People like to argue about tuners and pre-selectors so I would like to
expand on this a little.

A pre-selector is basically a band pass filter. Main use is to attenuate
out of band signals that may, depending on how good your radios blocking
is, be very helpful in reducing false images from showing up and making
reception of in band signals messy and confusing. Some units are
adjustable to the point that even some in band signals can be
attenuated. This fine-tuning is good from the standpoint that radio has
a narrower range of signals to block and this should result in improved
signal to noise as any time you limit the bandwidth of a spectrum the
noise floor drops. Noise is broadband energy and any time you limit the
received bandwidth you reduce the noise power. Obviously the better the
receiver is designed the less there is to be gained by using a
pre-selector.

An antenna tuner is a circuit used to resonate an antenna at the
frequency of operation. The effect on reception appears similar but
occurs for a different reason. Because the action of the tuner causes
the antenna to be optimized for the frequency of operation, the range of
frequencies above and below it are relatively attenuated due to not
being picked up as efficiently so you get a similar result but for a
different reason.

Why is the distinction important? Because the pre-selector can go
anywhere in the transmission line (coax) from antenna to radio and is
most often conveniently located near the radio. The tuner needs to be a
part of the antenna and so is located there where its output is at the
coax transmission line to the radio.

The pre-selector is an in line band-pass filter that can go anywhere
along the transmission line. The antenna tuner is located at and is
actually a part of the antenna.

What's is that? You say hams use antenna tuners in the shack for
transmitting purposes. This is not a good practice but if they are using
an antenna that is close to resonance and are just trying to protect the
transmitter from dealing with the additional reflected power then its OK
but in using it they are not improving how well their antenna functions.
The tuner in the shack does not improve or change how well their antenna
radiates.

Another thing people keep endless repeating is that nether antenna
tuners or pre-selectors help and just make signals louder (they mean
stronger), which of course with the AGC operation of the radio means the
result of using either is the S meter reads higher. This is only true
for medium to strong signals. For a weak signal, the signal to noise
should at least have a small improvement, determined by how weak the
signal was to begin with, receiver design, local noise, and current
propagation. If the signal is very weak, the tuner and pre-selector
could result in it being readable. Here the antenna tuner has the best
possibility of making a signal that is below the receiver noise floor
strong enough to be heard (detected) on the radio.

In summery, in my opinion, a pre-selector would be a good bet to improve
portable reception when connected to an external antenna especially the
worse case single conversion units. Following that in usefulness would
be an antenna tuner. People chasing DX with tabletop units might want to
try antenna tuners where less useful for them would be pre-selector use.

--
Telamon
Ventura, California
  #3   Report Post  
Old March 8th 06, 11:32 PM posted to rec.radio.shortwave
Bob Miller
 
Posts: n/a
Default Why Antenna Tuners Aren't Necessarily Useful for Shortwave Listening - Question Shortwave Listening (SWL) Antenna Tuners - Do You Have An Opinion ?

On Wed, 08 Mar 2006 20:59:22 GMT, Telamon
wrote:


In summery, in my opinion, a pre-selector would be a good bet to improve
portable reception when connected to an external antenna especially the
worse case single conversion units. Following that in usefulness would
be an antenna tuner. People chasing DX with tabletop units might want to
try antenna tuners where less useful for them would be pre-selector use.


And, I would pre-sume the "pre-amp" is different from the
pre-selector?

bob
k5qwg

  #4   Report Post  
Old March 8th 06, 11:39 PM posted to rec.radio.shortwave
David
 
Posts: n/a
Default Why Antenna Tuners Aren't Necessarily Useful for Shortwave Listening - Question Shortwave Listening (SWL) Antenna Tuners - Do You Have An Opinion ?

On Wed, 08 Mar 2006 22:32:23 GMT, Bob Miller
wrote:

On Wed, 08 Mar 2006 20:59:22 GMT, Telamon
wrote:


In summery, in my opinion, a pre-selector would be a good bet to improve
portable reception when connected to an external antenna especially the
worse case single conversion units. Following that in usefulness would
be an antenna tuner. People chasing DX with tabletop units might want to
try antenna tuners where less useful for them would be pre-selector use.


And, I would pre-sume the "pre-amp" is different from the
pre-selector?

bob
k5qwg

A receiver pre-amp can get the signal (and noise) above the AGC
threshold so at least the volume will be constant. A pre-amp between
the antenna and the transmission line can keep the cable from
attenuating the signal too much. However, at HF frequencies, line
losses are for the most part inconsequential.

  #5   Report Post  
Old March 9th 06, 12:18 AM posted to rec.radio.shortwave
Telamon
 
Posts: n/a
Default Why Antenna Tuners Aren't Necessarily Useful for Shortwave Listening - Question Shortwave Listening (SWL) Antenna Tuners - Do You Have An Opinion ?

In article ,
Bob Miller wrote:

On Wed, 08 Mar 2006 20:59:22 GMT, Telamon
wrote:


In summery, in my opinion, a pre-selector would be a good bet to improve
portable reception when connected to an external antenna especially the
worse case single conversion units. Following that in usefulness would
be an antenna tuner. People chasing DX with tabletop units might want to
try antenna tuners where less useful for them would be pre-selector use.


And, I would pre-sume the "pre-amp" is different from the
pre-selector?


Good assumption.

I'm not big on pre-amps because they add their own noise to the existing
signal to noise but they can help. For an amp the be a help it must be
low noise and the best location would be at the antenna. Amps are best
used where you have a long run of coax. Other feature enhancements of
the amp design can come into play to make them more valuable.

--
Telamon
Ventura, California


  #6   Report Post  
Old March 10th 06, 12:51 AM posted to rec.radio.shortwave
Slow Code
 
Posts: n/a
Default Why Antenna Tuners Aren't Necessarily Useful for Shortwave Listening - Question Shortwave Listening (SWL) Antenna Tuners - Do You Have An Opinion ?

Telamon wrote in
:

In article et,
Slow Code wrote:

"RHF" wrote in
ups.com:

For One and All,

QUESTION - Shortwave Listening (SWL) Antenna Tuners
- - - Do You Have An Opinion ? - - -

Why Antenna Tuners Aren't Necessarily Useful for Shortwave Listening
http://www.nyx.net/~dgrunber/tuner.ssi
- - - by - - - Daniel A. Grunberg

Here is "Dan Grunberg's Home Page"
http://www.nyx.net/~dgrunber/

Welcome - Here are some of my documents that may interest you.

TOPIC - SHORTWAVE RADIO :

* Advice to Shortwave Newbies
(Useful sources of information and useful links)

* Minimal Antennas and Grounds
(Why they may be all you need)

* So You're Certain You Need an Outdoor Antenna
(With a link to a reasonable design)

* Why Antenna Tuners Aren't Necessarily Useful
for Shortwave Listening
(This article could save you some money)

* A Rambling Review of the Lowe HF-150
(A nice receiver)

* Nifty 48-Inch (122-cm) Whip Antenna
with a PL-259 Connector

* The Sony 7600G and Its Synchronous Detector
(Why sync detectors are worth having)

* Analog vs. Digital Receivers (an introduction)

* Preventing Wire Antennas from Breaking in the Wind


and that's Today's On-Topic Post - iane ~ RHF
.
.
. .



Nice on-topic post. A tuner isn't really necessary for impedance
matching, but it can act as a pre-selector if your receiver has a poor
front end in it. Which can help improve things in some situations.


People like to argue about tuners and pre-selectors so I would like to
expand on this a little.

A pre-selector is basically a band pass filter. Main use is to attenuate
out of band signals that may, depending on how good your radios blocking
is, be very helpful in reducing false images from showing up and making
reception of in band signals messy and confusing. Some units are
adjustable to the point that even some in band signals can be
attenuated. This fine-tuning is good from the standpoint that radio has
a narrower range of signals to block and this should result in improved
signal to noise as any time you limit the bandwidth of a spectrum the
noise floor drops. Noise is broadband energy and any time you limit the
received bandwidth you reduce the noise power. Obviously the better the
receiver is designed the less there is to be gained by using a
pre-selector.

An antenna tuner is a circuit used to resonate an antenna at the
frequency of operation. The effect on reception appears similar but
occurs for a different reason. Because the action of the tuner causes
the antenna to be optimized for the frequency of operation, the range of
frequencies above and below it are relatively attenuated due to not
being picked up as efficiently so you get a similar result but for a
different reason.

Why is the distinction important? Because the pre-selector can go
anywhere in the transmission line (coax) from antenna to radio and is
most often conveniently located near the radio. The tuner needs to be a
part of the antenna and so is located there where its output is at the
coax transmission line to the radio.

The pre-selector is an in line band-pass filter that can go anywhere
along the transmission line. The antenna tuner is located at and is
actually a part of the antenna.

What's is that? You say hams use antenna tuners in the shack for
transmitting purposes. This is not a good practice but if they are using
an antenna that is close to resonance and are just trying to protect the
transmitter from dealing with the additional reflected power then its OK
but in using it they are not improving how well their antenna functions.
The tuner in the shack does not improve or change how well their antenna
radiates.

Another thing people keep endless repeating is that nether antenna
tuners or pre-selectors help and just make signals louder (they mean
stronger), which of course with the AGC operation of the radio means the
result of using either is the S meter reads higher. This is only true
for medium to strong signals. For a weak signal, the signal to noise
should at least have a small improvement, determined by how weak the
signal was to begin with, receiver design, local noise, and current
propagation. If the signal is very weak, the tuner and pre-selector
could result in it being readable. Here the antenna tuner has the best
possibility of making a signal that is below the receiver noise floor
strong enough to be heard (detected) on the radio.

In summery, in my opinion, a pre-selector would be a good bet to improve
portable reception when connected to an external antenna especially the
worse case single conversion units. Following that in usefulness would
be an antenna tuner. People chasing DX with tabletop units might want to
try antenna tuners where less useful for them would be pre-selector use.



As you said in your first sentence, people will argue about it. I agree
with what you say.

My point is that when you use a tuner with a receiver, it's acting as a
bandpass, which is the cause of the improvement if the receiver needs
front end help, Unwanted signals affecting the AGC are reduced. Impedance
matching with a tuner on HF I don't think you hear a difference. Maybe
we're meaning the same thing but saying it different ways.




SC
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Inverted ground plane antenna: compared with normal GP and low dipole. Serge Stroobandt, ON4BAA Antenna 8 February 24th 11 11:22 PM
Sony AN-LP1 Active Shortwave Loop Antenna - Battery Power and On-Off Switching with the Sony ICF-SW7600GR AM/FM Shortwave Radio. RHF Shortwave 0 January 22nd 06 03:40 PM
For Shortwave Listening (SWL) here is a "Simpler" Horizontal Loop Antenna in the Attic using common TV type Parts RHF Shortwave 1 November 24th 05 01:33 AM
Question is 'it' a Longwire {Random Wire} Antenna -or- Inverted "L" Antenna ? RHF Shortwave 5 November 6th 05 05:52 AM
I wonder... mike Shortwave 8 September 5th 03 04:38 AM


All times are GMT +1. The time now is 12:26 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017