Home |
Search |
Today's Posts |
#1
|
|||
|
|||
Need wire identification for Alliance Rotor motor
Saw a previous posting where a user was helped with a different model than mine a couple of years ago.
I've got an Alliance U-110 Tenna Rotor and the schematics are missing for the in house controller. Four terminals, labeled 1-4, no idea how they connect with with the wires. I inherited a system already in use, and the wires which are in place are red, green, black and white. Any ideas about which goes to which terminal? Sadly uneducated, RebDaniel |
#2
|
|||
|
|||
Need wire identification for Alliance Rotor motor
I just e-mailed you the schematic.
73 de Glenn AA5PK "rebdaniel" wrote in message ... Saw a previous posting where a user was helped with a different model than mine a couple of years ago. I've got an Alliance U-110 Tenna Rotor and the schematics are missing for the in house controller. Four terminals, labeled 1-4, no idea how they connect with with the wires. I inherited a system already in use, and the wires which are in place are red, green, black and white. Any ideas about which goes to which terminal? Sadly uneducated, RebDaniel -- rebdaniel |
#3
|
|||
|
|||
Need wire identification for Alliance Rotor motor
Well, I would have if your e-mail address had been valid.
"Glenn" wrote in message . .. I just e-mailed you the schematic. 73 de Glenn AA5PK "rebdaniel" wrote in message ... Saw a previous posting where a user was helped with a different model than mine a couple of years ago. I've got an Alliance U-110 Tenna Rotor and the schematics are missing for the in house controller. Four terminals, labeled 1-4, no idea how they connect with with the wires. I inherited a system already in use, and the wires which are in place are red, green, black and white. Any ideas about which goes to which terminal? Sadly uneducated, RebDaniel -- rebdaniel |
#4
|
|||
|
|||
Need wire identification for Alliance Rotor motor
"rebdaniel" wrote in message ... Saw a previous posting where a user was helped with a different model than mine a couple of years ago. I've got an Alliance U-110 Tenna Rotor and the schematics are missing for the in house controller. Four terminals, labeled 1-4, no idea how they connect with with the wires. I inherited a system already in use, and the wires which are in place are red, green, black and white. Any ideas about which goes to which terminal? Sadly uneducated, RebDaniel The wire colors mean nothing. If you can look at the rotator, then the same number on the rotator goes to the same number on the house unit. I usually use the colors of the resistor code when wiring up things, just start with the lowest color wire and go up. I doubt anyone else does this. |
#5
|
|||
|
|||
Need wire identification for Alliance Rotor motor
"Ralph Mowery" wrote in message
m... Don't you just hate that ? I do and do not try to send the needed info a second time to people that will not use a valid email address. At least get a throw-away Hotmail or Yahoo account :O) I liked your method of using the resistor color code when attaching colored wires. I'll have to keep that in mind. 73 de Glenn AA5PK |
#6
|
|||
|
|||
Need wire identification for Alliance Rotor motor
On Wed, 27 Aug 2008 19:55:05 +0100, rebdaniel
wrote: Saw a previous posting where a user was helped with a different model than mine a couple of years ago. I've got an Alliance U-110 Tenna Rotor and the schematics are missing for the in house controller. Four terminals, labeled 1-4, no idea how they connect with with the wires. I inherited a system already in use, and the wires which are in place are red, green, black and white. Any ideas about which goes to which terminal? Sadly uneducated, RebDaniel I used to install U-100's many years ago (a side job while in college) and remember if you use the included strain relief at the motor end with a four wire flat cable, the four wires became 1, 2, 4, and 3 because of the way the screw terminals were laid out on the motor. You, therefore, had to swap the 3rd and 4th wires on the control box. I always wondered why they did it that way. We had many repair calls because an owner would disconnect the control box and then reconnect it the obvious way... wrong. Perhaps they fixed that problem on the U-110. |
#7
|
|||
|
|||
Need wire identification for Alliance Rotor motor
"Glenn" wrote in message . .. Well, I would have if your e-mail address had been valid. "Glenn" wrote in message . .. I just e-mailed you the schematic. 73 de Glenn AA5PK Don't you just hate that ? I do and do not try to send the needed info a second time to people that will not use a valid email address. |
#8
|
|||
|
|||
Quote:
|
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Need wire identification for Alliance Rotor motor | Equipment | |||
Need wire identification for Alliance Rotor motor | Equipment | |||
FS: Alliance tenna rotor | Boatanchors | |||
FA: Alliance HD-73 Rotor | Swap |