Home |
Search |
Today's Posts |
#1
|
|||
|
|||
Lithium Battery Leakage?
I apologize if this subject has been discussed here recently but I am not a
regular subscriber. I have a Kenwood TS-940, bought in 1989. The memory and timer functions work okay but I have been told that the lithium batteries used in these circuits could leak and damage if not replaced after so many years. Is this a real threat? If so, is it a lot of work? Appreciate comments on this. 73, Ben K8UYA |
#2
|
|||
|
|||
I apologize if this subject has been discussed here recently but I am not a
regular subscriber. I have a Kenwood TS-940, bought in 1989. The memory and timer functions work okay but I have been told that the lithium batteries used in these circuits could leak and damage if not replaced after so many years. Is this a real threat? If so, is it a lot of work? Appreciate comments I haven't heard of problems with lithium batteries leaking. That's a problem most usually ascribed to alkaline batteries, whose outer jackets can corrode as a result of the electrochemical reactions within the battery. However, your rig's battery may well be reaching the end of its use-life in this application - 10 years is the usual quoted range for low-power memory backup applications - and you may wish to consider replacing it for that reason. Replacing the battery may be either easy, or tricky, depending on the rig... I don't know about the TS-940. In some radios the battery is in a clip holder, and replacing it is trivially easy. In most radios, the battery is soldered into place, and it's necessary to unsolder it and solder in a new one - the usual static-discharge and don't-burn-up-the-board precautions should be taken. You'll probably find that your local Radio Shack will _not_ have a replacement battery with the same sort of solder tabs - you could either order the right battery from (e.g.) Digi-Key, or remove the old battery and solder in a battery holder (if you can find one which will fit), or improvise (attach lead wires to a lithium coin battery using a dab of silver-loaded conductive epoxy). In some radios, the battery provides backup power not only for the programming, but also for the radio firmware. Replacing the battery in these radios is tricky - in order to avoid losing the firmware you must jumper in an alternative DC power source when replacing the battery, or you must have the specialized kit needed to reprogram the firmware after replacing the battery. This is usually a job for a factory or factory-authorized service depot. -- Dave Platt AE6EO Hosting the Jade Warrior home page: http://www.radagast.org/jade-warrior I do _not_ wish to receive unsolicited commercial email, and I will boycott any company which has the gall to send me such ads! |
#3
|
|||
|
|||
I apologize if this subject has been discussed here recently but I am not a
regular subscriber. I have a Kenwood TS-940, bought in 1989. The memory and timer functions work okay but I have been told that the lithium batteries used in these circuits could leak and damage if not replaced after so many years. Is this a real threat? If so, is it a lot of work? Appreciate comments I haven't heard of problems with lithium batteries leaking. That's a problem most usually ascribed to alkaline batteries, whose outer jackets can corrode as a result of the electrochemical reactions within the battery. However, your rig's battery may well be reaching the end of its use-life in this application - 10 years is the usual quoted range for low-power memory backup applications - and you may wish to consider replacing it for that reason. Replacing the battery may be either easy, or tricky, depending on the rig... I don't know about the TS-940. In some radios the battery is in a clip holder, and replacing it is trivially easy. In most radios, the battery is soldered into place, and it's necessary to unsolder it and solder in a new one - the usual static-discharge and don't-burn-up-the-board precautions should be taken. You'll probably find that your local Radio Shack will _not_ have a replacement battery with the same sort of solder tabs - you could either order the right battery from (e.g.) Digi-Key, or remove the old battery and solder in a battery holder (if you can find one which will fit), or improvise (attach lead wires to a lithium coin battery using a dab of silver-loaded conductive epoxy). In some radios, the battery provides backup power not only for the programming, but also for the radio firmware. Replacing the battery in these radios is tricky - in order to avoid losing the firmware you must jumper in an alternative DC power source when replacing the battery, or you must have the specialized kit needed to reprogram the firmware after replacing the battery. This is usually a job for a factory or factory-authorized service depot. -- Dave Platt AE6EO Hosting the Jade Warrior home page: http://www.radagast.org/jade-warrior I do _not_ wish to receive unsolicited commercial email, and I will boycott any company which has the gall to send me such ads! |
#4
|
|||
|
|||
I have been told that the lithium
batteries used in these circuits could leak and damage if not replaced after so many years. Is this a real threat? Ben- While I can't say it would never happen, I have never experienced leakage from such a lithium battery. Common practice seems to be to leave it until it dies, unless you happen to be servicing an old radio for some other reason. I recently had an experience troubleshooting a problem with a twenty-year-old Icom radio. Assuming the battery was the problem, I replaced it. I found that the original battery still had a charge, and the replacement did not fix my problem! In fact, I used that old battery to temporarily replace a dead one in a ten-year-old Kenwood TS-50, while waiting for a new battery to arrive. Depending on the battery, nominal voltage may be around 3.2 to 3.6 volts. If you measure the old one with a high impedance meter, and it reads 3 volts or greater, then you still have some life left in it. If it measures below 3 volts, it may still function, but time is running out. 73, Fred, K4DII |
#5
|
|||
|
|||
I have been told that the lithium
batteries used in these circuits could leak and damage if not replaced after so many years. Is this a real threat? Ben- While I can't say it would never happen, I have never experienced leakage from such a lithium battery. Common practice seems to be to leave it until it dies, unless you happen to be servicing an old radio for some other reason. I recently had an experience troubleshooting a problem with a twenty-year-old Icom radio. Assuming the battery was the problem, I replaced it. I found that the original battery still had a charge, and the replacement did not fix my problem! In fact, I used that old battery to temporarily replace a dead one in a ten-year-old Kenwood TS-50, while waiting for a new battery to arrive. Depending on the battery, nominal voltage may be around 3.2 to 3.6 volts. If you measure the old one with a high impedance meter, and it reads 3 volts or greater, then you still have some life left in it. If it measures below 3 volts, it may still function, but time is running out. 73, Fred, K4DII |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Are Alincos Throw-Away Radios? (Finding a DJ-C5 Battery) | Equipment | |||
Are Alincos Throw-Away Radios? (Finding a DJ-C5 Battery) | Equipment | |||
ICOM IC735 lithium battery | Equipment | |||
ICOM IC735 lithium battery | Equipment |