Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Old August 31st 03, 06:18 AM
Walter
 
Posts: n/a
Default Should I run a Sky-wire loop?

Should I run a Sky-wire loop?


I currently have a dipole hung by two trees about 30 feet off the
ground.


I would replace the dipole and run the Skywire loop off the same
trees, along with two more trees at the same height as the current
dipole.

This antenna would only be used for receiving, and never for
transmitting, the same for the dipole.

My question is, does anybody think it will make enough of a difference
over the dipole to warrant running it?

I would also like to know what your views are on "grounding" either
my current dipole, or the Sky-wire.

Currently, I have the coax center wire soldered onto one end of the
dipole, and the braid soldered onto the other end. I was told that I
should also ground the braid before it comes into the house and into
the radio.

I do have a ground wire attached to GND screw on the back of the
radio, going outside to a piece of copper pipe pounded into the
ground. Is this enough, or do I need to also ground the braid, and if
so, how? Will grounding help my reception, or decrease the noise on
the line?

Thanks.
  #2   Report Post  
Old August 31st 03, 02:09 PM
Joe O
 
Posts: n/a
Default

A Horizontal Loop will pickup less vertically polarized atmospheric noise. I
am very satisfied with my 480 ft loop that is up 35 ft. For receive only, an
ATU would not be necessary, but it will improve the signal strength at some
frequencies.

My feedline is open line from the corner of the loop to the earth where
there is a 1:1 current type balun. I connect the shield of the coax to a 8
ft ground rod. If your area is prone to lightning, I would install a
polyphazer. The coax runs underground to the shack. The coax is only
connected to the rig when I am actually using the antenna.

This reconfiguration is relatively inexpensive. Go for it and compare the
results.

Joe O, KI5FJ

"Walter" wrote in message
om...
Should I run a Sky-wire loop?


I currently have a dipole hung by two trees about 30 feet off the
ground.


I would replace the dipole and run the Skywire loop off the same
trees, along with two more trees at the same height as the current
dipole.

This antenna would only be used for receiving, and never for
transmitting, the same for the dipole.

My question is, does anybody think it will make enough of a difference
over the dipole to warrant running it?

I would also like to know what your views are on "grounding" either
my current dipole, or the Sky-wire.

Currently, I have the coax center wire soldered onto one end of the
dipole, and the braid soldered onto the other end. I was told that I
should also ground the braid before it comes into the house and into
the radio.

I do have a ground wire attached to GND screw on the back of the
radio, going outside to a piece of copper pipe pounded into the
ground. Is this enough, or do I need to also ground the braid, and if
so, how? Will grounding help my reception, or decrease the noise on
the line?

Thanks.



  #3   Report Post  
Old August 31st 03, 04:43 PM
'Doc
 
Posts: n/a
Default

Walter,
It depends a lot on what type of feed line you use. If
you use coax to feed the loop, performance will probably
be about the same or worse than the dipole. If you use an
open wire or ladder line feed line through a tuner, you will
probably see ~some~ difference between the two antennas. How
much is anyone's guess. I like large loop antennas. I've
found that using ladder line and a tuner will make them usable
on more than one band and usually performs better than a dipole
used the same way (I don't have the best place to put up an
antenna to start with). Every installation is different so
what works great for me, here, may not work very well at your
location. Having said that, try the loop. If you don't like
how it performs, change back.
'Doc
  #4   Report Post  
Old August 31st 03, 08:56 PM
Dale Parfitt
 
Posts: n/a
Default



Joe O wrote:

A Horizontal Loop will pickup less vertically polarized atmospheric noise.


Could you give an explaination for why this is?

Dale W4OP

  #5   Report Post  
Old September 1st 03, 12:37 AM
Walter
 
Posts: n/a
Default

If I use a Polyphaser lightning arrestor, that is grounded to a
grounding rod, and hooked to the feed line, and the radio, will that
do the same job as grounding the coax feed line braid?

or are we talking about two different grounding steps?

thanks for the help!!!


  #6   Report Post  
Old September 5th 03, 02:52 AM
Walter
 
Posts: n/a
Default

I have created a new group on yahoo about skywires.

please visit and add your comments.

thanks

http://groups.yahoo.com/group/SkyWires/
  #7   Report Post  
Old September 5th 03, 06:57 PM
Richard Harrison
 
Posts: n/a
Default

Dale, W4OP wrote:
"Could you give an explanation of why this is?"

Joe O. had written:
"A Horizontal Loop will pickup less vertically polarized atmospheric
noise."

ON4UN wrote on page 10-7 of "Low-Band DXing":
"The loop will act as any horizontally polarized antenna over real
ground; its wave angle will depend on the height of the antenna over the
ground."

So, the short answer is "cross-polarization".

Most noise is local and reaches a receiver through ground-wave
propagation. Horizontally polarized waves have zero ground-wave
propagation. Their low-angle reflections are out-of-phase with the
direct wave.

Horzontal antennas are in general quieter than vertical antennas.
Cross-polarization loss has been often reported as about 20 db.

Loops, small in terms of wavelength, tend to have the same volts and
amps induced into all their increments. This helps reduce sensitivity to
overloads from high-power signals at frequencies far below the desired
reception, as might be received on a voltage-probe antenna.

Best regards, Richard Harrison, KB5WZI



  #8   Report Post  
Old September 6th 03, 05:00 AM
rich a.
 
Posts: n/a
Default

Should I run a Sky-wire loop?

Walter,

Give the Skywire loop a try....I put one up almost a year ago and it
definitely is better than my other wire antenna ( a 40m dipole). Mine
is approx 440' long and is shaped more like a rectangle than a perfect
round (or square) loop. Each corner is at a different elevation, the
higest 35' , the lowest 20'. I feed it with RG8X, no balun, and my
K2's autotuner permits effective operation on all HF bands at less
than 2-1 SWR, except on 160 where it only tunes down to 3.5 to 1. I
haven't done it yet but I've worked out a way to enlarge it another
100', so the 160m swr should come down. I also plan to try switching
to 450 ohm ladder line feed.....everyone says it will work even
better. Did I mention it is the "quietest' recieving antenna I've
used?.... But don't limit its use to only recieving....the horizontal
loop is a great transmitting antenna too. My first contact with mine
was on 20m to Tierra del Fuego at the southern tip of Argentina ( 5
watts ssb, got a 5x5 sig report!). Seems to be somewhat omni
directional too as I've worked dx in all directions. I don't claim it
will outperform a good beam on a tower but the price is right (cheap)
and its realatively easy to make. Go for it!

Regards,

Rich K2CPE
  #9   Report Post  
Old September 6th 03, 05:58 AM
Mark Keith
 
Posts: n/a
Default

(Richard Harrison) wrote in message ...
Dale, W4OP wrote:
"Could you give an explanation of why this is?"

Joe O. had written:
"A Horizontal Loop will pickup less vertically polarized atmospheric
noise."


Than a vertically polarized antenna, yes.

ON4UN wrote on page 10-7 of "Low-Band DXing":
"The loop will act as any horizontally polarized antenna over real
ground; its wave angle will depend on the height of the antenna over the
ground."


I tend to agree with this statement.

So, the short answer is "cross-polarization".


The dipole is horizontal also. Or I would assume anyway if hung from
two trees.

Most noise is local and reaches a receiver through ground-wave
propagation. Horizontally polarized waves have zero ground-wave
propagation. Their low-angle reflections are out-of-phase with the
direct wave.

Horzontal antennas are in general quieter than vertical antennas.
Cross-polarization loss has been often reported as about 20 db.

Loops, small in terms of wavelength, tend to have the same volts and
amps induced into all their increments. This helps reduce sensitivity to
overloads from high-power signals at frequencies far below the desired
reception, as might be received on a voltage-probe antenna.


A "sky wire" loop, as usually thought of, is not a small loop though.
Thats a name given to the practice of feeding a loop on all bands,
with the loop usually a full wave or larger for the lowest band to be
used. Kind of the loop equal to feeding a 1/2 wave low band dipole on
all bands with ladder line...
As far as noise, if the dipole and loop are both horizontal, there
should be little if any difference in noise received, unless the
pattern of the particular antenna favors the noise source. I haven't
done extensive tests, but it's my opinion that the common perception
of large loops being quieter than large dipoles is wishful thinking.
I've never noticed any real difference. It's always been my experience
that if a certain antenna receives less noise than another, not
counting any local noise ingress problems, it's inferior in the
direction of the noise received than the other. "All the same polarity
and the noise in the far field"
Noise is rf same as any other. All good antennas pick up a lot of
noise, if there is noise to be picked up. If I have an antenna thats
"too" quiet, I start to worry..:/ As far as the original poster... I
don't think changing antennas is worth the hassle just for SWL use.
Maybe not even if he transmitted. I guess would depend on the
particular band to be used. The patterns will be different on the
various higher bands, but I doubt different enough to make or break
things with most signals. If he's not hearing a certain station on the
dipole, he probably wouldn't on the loop either. MK
  #10   Report Post  
Old September 6th 03, 01:43 PM
K9SQG
 
Posts: n/a
Default

Rich,

It is much more of an advantage to run open wire line for multiband operation
due to the much lower losses.

73s,

Evan
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Distance to Link Coupling in a Loop Antenna Al Antenna 6 October 28th 03 01:02 AM
SWL tuning an MFJ loop? Hatfield Antenna 3 July 25th 03 11:44 PM
Snap-on choke hurts shielded loop Loopfan Antenna 3 July 14th 03 08:30 PM
Feedpoint impedence / wire diameter Tom Bruhns Antenna 0 July 10th 03 08:23 PM


All times are GMT +1. The time now is 03:43 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017