A Radio forum. RadioBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » RadioBanter forum » rec.radio.amateur » Antenna
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

HF Antenna Pickup Truck



 
 
Thread Tools Display Modes
  #1  
Old November 26th 04, 07:23 PM
Gary Boyer
Guest
 
Posts: n/a
Default HF Antenna Pickup Truck

Has anyone tried mounting a magnet mount hf antenna (Hamstick) on the top of
a metal toolbox, the kind that are used in the back of pickup
trucks......just curious...I realize the best place is on top of the
cab....tnx...Gary, K8BY


  #2  
Old November 26th 04, 07:44 PM
Z.Z.
Guest
 
Posts: n/a
Default

Gary Boyer wrote:

Has anyone tried mounting a magnet mount hf antenna (Hamstick) on the
top of a metal toolbox ...


No, but does your truck have stake pockets? There's an outfit that makes
antenna mounts that fit in the stake pockets of pickups. I got one for my
Ranger to mount a 10M Hamstick. Works pretty well and is a rugged mount. It
would probably handle something a lot bigger than the Hamstick. Can't
remember the name but they advertise in QST. I had tried a magmount in the
middle of the bed but couldn't tune the Hamstick there. I'd guess you'd
have the same problem due to the cab. Using the stake pocket mount (in the
rear-most pocket on the pasenger side) it works great.

OTOH, a friend of mine runs a screwdriver antenna mounted to the rear wall
of his toolbox in his big Dodge PU and it seems to work OK...

73.. Mark AA7TA
  #3  
Old November 26th 04, 08:44 PM
Dave Platt
Guest
 
Posts: n/a
Default

Has anyone tried mounting a magnet mount hf antenna (Hamstick) on the top of
a metal toolbox, the kind that are used in the back of pickup
trucks......just curious...I realize the best place is on top of the
cab....tnx...Gary, K8BY


There are two aspects to this: mechanical and electrical.

Mechanically, I'd imagine you'll be OK. A Hamstick is pretty thin,
and wouldn't have a large amount of wind-drag force on it. Assuming
that the toolbox is solidly constructed, the magmount's grip on its
roof would be sufficient to keep the antenna in place, and the drag
and torque on the toolbox lid's hinges probably wouldn't be enough to
matter. If I were you I'd arrange to snub the feed cable - clamp it
down to the frame somehow, so that if the mag-mount does pop loose you
don't find yourself dragging the antenna on the road behind the vehicle.

Electrically, there are a couple of issues. For one thing, if the
tookbox is immediately behind the cab, this arrangement might put the
Hamstick quite close to metal portions of the cab roof or uprights.
This sort of close antenna-to-body coupling tends to reduce the
antenna efficiency. Keep the antenna as far away from the metal body
as you can safely manage.

From what I've read, HF magmounts often don't have enough coupling
capacitance to give a really satisfactory grounding, even when mounted
right on the roof. It's usually desirable (and often necessary) to
run a short, fat grounding lead from the antenna base/feedpoint to a
solid grounding location on the vehicle frame. You should probably do
something like this if you do decide to mag-mount on the toolbox.

--
Dave Platt AE6EO
Hosting the Jade Warrior home page: http://www.radagast.org/jade-warrior
I do _not_ wish to receive unsolicited commercial email, and I will
boycott any company which has the gall to send me such ads!
  #4  
Old November 26th 04, 11:17 PM
Chuck
Guest
 
Posts: n/a
Default

Aren't these tool boxes generally aluminum or stainless steel?

Gary Boyer wrote:
Has anyone tried mounting a magnet mount hf antenna (Hamstick) on the top of
a metal toolbox, the kind that are used in the back of pickup
trucks......just curious...I realize the best place is on top of the
cab....tnx...Gary, K8BY


  #5  
Old November 27th 04, 12:34 AM
JGBOYLES
Guest
 
Posts: n/a
Default

Has anyone tried mounting a magnet mount hf antenna (Hamstick) on the top of
a metal toolbox?


Hi Gary, If your toolbox is like mine, it is Aluminum, and the mag mount
won't stick. I attached a small steel plate on the top of the box and use it
for a 2M mag mount.
For my homebrew HF mobile antenna I use a mounting system on the backside of
the box. I get good results with my bugcatcher type antenna on 80m-17m mounted
in this location. The loading coil is about 1 foot above the cab top. Since a
Hamstick is continously loaded, and may not be as efficient as a bugcatcher,
you may not have similar results, mounting at the rear of the box.


73 Gary N4AST
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Inverted ground plane antenna: compared with normal GP and low dipole. Serge Stroobandt, ON4BAA Antenna 8 February 24th 11 11:22 PM
The "TRICK" to TV 'type' Coax Cable [Shielded] SWL Loop Antennas {RHF} RHF Antenna 27 November 3rd 04 02:38 PM
Mobile Ant L match ? Henry Kolesnik Antenna 14 January 20th 04 05:08 AM
Poor quality low + High TV channels? How much dB in Preamp? lbbs Antenna 16 December 13th 03 04:01 PM


All times are GMT +1. The time now is 02:36 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright 2004-2014 RadioBanter.
The comments are property of their posters.