RG-58 compared to RG-174
 

Hello, I am going to be making some adaptor harnesses for my HT, they are
going to have a PL-259 on one end and a SMA male end on the other, my
question is are the center conductor's inside the RG-58 and RG-174 the same
diameter because I see all the jumper harness's that are available
commercially made of RG-174, but when I see DIY pages they are made of
RG-58, and I just want to make sure. I read that RG-58 has alot less loss
and is cheaper. Thanks

Dustin wrote:

Hello, I am going to be making some adaptor harnesses for my HT, they are
going to have a PL-259 on one end and a SMA male end on the other, my
question is are the center conductor's inside the RG-58 and RG-174 the
same
diameter because I see all the jumper harness's that are available
commercially made of RG-174, but when I see DIY pages they are made of
RG-58, and I just want to make sure. I read that RG-58 has alot less loss
and is cheaper. Thanks


rg-58 is cheaper.. bigger and has less loss


--
Registered Linux User #346565

"Dustin" wrote in message
...
Hello, I am going to be making some adaptor harnesses for my HT, they are
going to have a PL-259 on one end and a SMA male end on the other, my
question is are the center conductor's inside the RG-58 and RG-174 the
same
diameter because I see all the jumper harness's that are available
commercially made of RG-174, but when I see DIY pages they are made of
RG-58, and I just want to make sure. I read that RG-58 has alot less loss
and is cheaper. Thanks

As the impedance is determined by the ratio of the outer conductor to the
center conductor (for the same insulation between them) the 174 has to have
a smaller center conductor than the 58. RG-58 does have more loss but for
less than 5 feet on two meters I doubt that you will notice it. Probably
not even on 440 mhz . If using the RG-58 try to find some with a stranded
center conductor as much of it seems to be solid wire.

Hello, I am going to be making some adaptor harnesses for my HT, they are
going to have a PL-259 on one end and a SMA male end on the other, my
question is are the center conductor's inside the RG-58 and RG-174 the same
diameter because I see all the jumper harness's that are available
commercially made of RG-174, but when I see DIY pages they are made of
RG-58, and I just want to make sure. I read that RG-58 has alot less loss
and is cheaper. Thanks

RG-58 has lower loss than RG-174, because RG-58's center conductor is
larger in diameter than RG-174s. You'll need to buy SMA connectors
which are specifically designed for RG-58 - this cable won't fit into
an SMA connector made for RG-174.

Because of its larger diameter, it's also likely to be stiffer than
RG-174. This means that it could put more stress on the HT's SMA
socket, if the harness is pulled or pushed sideways.

The lower loss in RG-58 isn't likely to make a significant amount of
difference for a short harness, at least not at 2-meter frequencies.

--
Dave Platt AE6EO
Hosting the Jade Warrior home page: http://www.radagast.org/jade-warrior
I do _not_ wish to receive unsolicited commercial email, and I will
boycott any company which has the gall to send me such ads!

Use RG-174. Finding an inexpensive SMA connector for RG-58 is difficult.

Jim


"Dustin"
shared these priceless pearls of wisdom:

-Hello, I am going to be making some adaptor harnesses for my HT, they are
-going to have a PL-259 on one end and a SMA male end on the other, my
-question is are the center conductor's inside the RG-58 and RG-174 the same
-diameter because I see all the jumper harness's that are available
-commercially made of RG-174, but when I see DIY pages they are made of
-RG-58, and I just want to make sure. I read that RG-58 has alot less loss
-and is cheaper. Thanks
-
-

Jim Weir, VP Eng. RST Eng. WX6RST
A&P, CFI, and other good alphabet soup

Why would you do that? Solid has less loss. If you are worried about it
flexing too much and work-hardening (or breaking) the center conductor, use a
strain relief of shrink sleeving at both ends.

Jim



"Ralph Mowery"
shared these priceless pearls of wisdom:

- If using the RG-58 try to find some with a stranded
-center conductor as much of it seems to be solid wire.
-
-

Jim Weir, VP Eng. RST Eng. WX6RST
A&P, CFI, and other good alphabet soup

Why would you do that? Solid has less loss. If you are worried about it
flexing too much and work-hardening (or breaking) the center conductor, use a
strain relief of shrink sleeving at both ends.

To my mind, the stiffer the cable, the more stress it's going to put
on the HT's SMA jack. Stiffening the cable via heatshrink tubing is
only going to make this worse, by increasing the moment arm.

SMA jacks on some HTs (e.g. the VX-5) are rather notorious for working
loose, even under the modest stress and strain of a rubber-duck
antenna. IMHO, SMA is a fine connector for intra-cabinet connections
and fixed-station applications, but it's less than ideal for antenna
connections on handhelds.

--
Dave Platt AE6EO
Hosting the Jade Warrior home page: http://www.radagast.org/jade-warrior
I do _not_ wish to receive unsolicited commercial email, and I will
boycott any company which has the gall to send me such ads!

On Sun, 28 Mar 2004 14:39:58 -0500, "Ralph Mowery"
wrote:
then the wire will work harden and break

Copper?

In article ,
Richard Clark wrote:

then the wire will work harden and break

Copper?

That's my experience, and a few minutes of Google-searching the Web
comes up with numerous references stating that copper does suffer from
work hardening after cold-deformation. The extent depends on the
purity of the copper and on what other metals it has been alloyed
with. [Lead is apparently one of the few metals not subject to work
hardening.]

This process can be reversed by annealing, but that's a bit tricky to
do if the copper is already part of a coaxial cable :-)

--
Dave Platt AE6EO
Hosting the Jade Warrior home page: http://www.radagast.org/jade-warrior
I do _not_ wish to receive unsolicited commercial email, and I will
boycott any company which has the gall to send me such ads!

On Sun, 28 Mar 2004 18:55:40 -0000, (Dave Platt)
wrote:

copper does suffer from
work hardening after cold-deformation.

For an HT application?

The extent depends on the
purity of the copper

Generally 99.95% or better for simple wire. Copper pipe is another
matter, but for an HT application?

and on what other metals it has been alloyed
with. [Lead is apparently one of the few metals not subject to work
hardening.]

And the lead amalgam (with tin) is the MOST likely to be found - for
an HT application.

Work hardening would require a severe kink, about the same radius of
the wire. The insulation is going to limit that bend to easily ten
times that, and typical practice to 100's of times that. And as for
repetitive (the work part of the hardening) stress, maybe for an
automatic door opener, but for an HT application? The topic
application is for jumper connections where the SMA connector is far
more likely to fail.

C'mon, now guys, let's worry about what is likely to break, not about
everything that might fail. May as well take out an
asteroid-collision policy.

73's
Richard Clark, KB7QHC