|
Trap antenna
HI,
I picked up two coils that could be a trap for the CWA-840 COMET antenna. (They have two stickers "CL-840"). The manual of the CWA-840 says : 40/80m dipole. I found amazing that there isn't any capacitor in // of these coils... These coils measure 76uH. Could someone tell me how they works ? In the manual of the CWA-840, each leg of the 7MHz section, is 11.1meters in lenght , wich, it seems to me, that it is rather longer that 1/4 wave. (10.1m). Why ? Thanks a lot for your answers CWA-840: -----[ ]-------------ooo--//-- 2.3m coil 11.1m balun |
Trap antenna
"béo-master" wrote in message . fr... HI, I picked up two coils that could be a trap for the CWA-840 COMET antenna. (They have two stickers "CL-840"). The manual of the CWA-840 says : 40/80m dipole. I found amazing that there isn't any capacitor in // of these coils... These coils measure 76uH. Could someone tell me how they works ? In the manual of the CWA-840, each leg of the 7MHz section, is 11.1meters in lenght , wich, it seems to me, that it is rather longer that 1/4 wave. (10.1m). Why ? Thanks a lot for your answers CWA-840: -----[ ]-------------ooo--//-- 2.3m coil 11.1m balun All coils are self-resonant at some frequency. Wind it right and off you go! "Sal" |
Trap antenna
On 10/20/2011 5:28 PM, Sal wrote:
wrote in message . fr... HI, I picked up two coils that could be a trap for the CWA-840 COMET antenna. (They have two stickers "CL-840"). The manual of the CWA-840 says : 40/80m dipole. I found amazing that there isn't any capacitor in // of these coils... These coils measure 76uH. Could someone tell me how they works ? In the manual of the CWA-840, each leg of the 7MHz section, is 11.1meters in lenght , wich, it seems to me, that it is rather longer that 1/4 wave. (10.1m). Why ? Thanks a lot for your answers CWA-840: -----[ ]-------------ooo--//-- 2.3m coil 11.1m balun All coils are self-resonant at some frequency. Wind it right and off you go! "Sal" Good point, Sal. I hope the OP has a GDO to tell him the self-resonant frequency. If not, there are other ways. John, KD5YI |
Trap antenna
|
Trap antenna
|
Trap antenna
béo-master wrote in
. fr: HI, I picked up two coils that could be a trap for the CWA-840 COMET antenna. (They have two stickers "CL-840"). The manual of the CWA-840 says : 40/80m dipole. I found amazing that there isn't any capacitor in // of these coils... These coils measure 76uH. That is a rather simplistic characterisation of the trap. If you were to measure its impedance over a wide range of frequency, the data would give a better idea of the extent of any parallel capacitance (and there has to be some, even if only stray capacitance. Somethimes the capacitance is between some metal tubes that make the end supports for the trap. Note that measuring the impedance of traps is very challenging. Could someone tell me how they works ? The trap introduces some reactance and resistance that is intended with appropriate conductor lengths, to give a modestly low VSWR at the frequencies of interest. The traditional explanation is that they are resonant at one of the frequencies of operation, and act like a switch, cutting off current to the outboard legs. Of course, current would flow in the outboard legs eve if you used a physical switch. That explanation is appealing, but limits your options. There are advantages is making the resonant frequency of a trap fall outside the bands of interest. In the manual of the CWA-840, each leg of the 7MHz section, is 11.1meters in lenght , wich, it seems to me, that it is rather longer that 1/4 wave. (10.1m). Why ? See above. Thanks a lot for your answers CWA-840: -----[ ]-------------ooo--//-- 2.3m coil 11.1m balun The trap is probably self resonant below 40m... but that is just a guess from experience of having designed such things. Owen |
Trap antenna
Thanks a lot for your answers.
I have now most of the explainations. Thanks for the links. (I had already read some) |
Trap antenna
On 10/20/2011 09:19 AM, béo-master wrote:
HI, I picked up two coils that could be a trap for the CWA-840 COMET antenna. (They have two stickers "CL-840"). The manual of the CWA-840 says : 40/80m dipole. I found amazing that there isn't any capacitor in // of these coils... These coils measure 76uH. Could someone tell me how they works ? In the manual of the CWA-840, each leg of the 7MHz section, is 11.1meters in lenght , wich, it seems to me, that it is rather longer that 1/4 wave. (10.1m). Why ? Thanks a lot for your answers CWA-840: -----[ ]-------------ooo--//-- 2.3m coil 11.1m balun This is not a trap antenna: 1)- At 40 meters the coil works like a medium impedance insulator,76uH represents 5300 ohms. 2)- At 80 meters, the antenna works like a vertical mobile antenna, the coil resonates with the 2.3m section. I made several of these antennas years ago, and the 40 meter section is always longer than in a simple 40 meter dipole. -- Alejandro Lieber LU1FCR Rosario Argentina Real-Time F2-Layer Critical Frequency Map foF2: http://1fcr.com.ar |
Trap antenna
On 10/21/2011 10:00 PM, Owen Duffy wrote:
wrote in . fr: HI, I picked up two coils that could be a trap for the CWA-840 COMET antenna. (They have two stickers "CL-840"). The manual of the CWA-840 says : 40/80m dipole. I found amazing that there isn't any capacitor in // of these coils... These coils measure 76uH. That is a rather simplistic characterisation of the trap. If you were to measure its impedance over a wide range of frequency, the data would give a better idea of the extent of any parallel capacitance (and there has to be some, even if only stray capacitance. Somethimes the capacitance is between some metal tubes that make the end supports for the trap. or C from the winding of the coil to the surrounding tubing. Or the "self C" of the coil (viz Medhurst's formulae for self C of an inductor) There's a goodly bit of empiricism in trap design. You can use basic physics to calculate, but there's enough non-idealness in most construction techniques that the calculations get you to a starting point. (e.g. you could model the transition from the antenna element to the coil in the trap with a lot of detail, or you could just build one and try it, then adjust) Note that measuring the impedance of traps is very challenging. Could someone tell me how they works ? The trap introduces some reactance and resistance that is intended with appropriate conductor lengths, to give a modestly low VSWR at the frequencies of interest. The traditional explanation is that they are resonant at one of the frequencies of operation, and act like a switch, cutting off current to the outboard legs. Of course, current would flow in the outboard legs eve if you used a physical switch. That explanation is appealing, but limits your options. There are advantages is making the resonant frequency of a trap fall outside the bands of interes Here's a (not very realistic) example of how it might work Say you want an antenna that covers both 10m and 15m. You start with a 10 meter resonant antenna. Now hook a trap which has very high impedance at 10m on the end of it. Since it's high Z, not much current flows, so it doesn't change the 10m behavior very much. But, you also want it to work at 15m. So you figure out how long an additional element you need to put "outboard" of the trap to get the system to resonate. Typically, the trap is a parallel LC, so below resonance, it looks somewhat inductive. Since a short element looks capacitive, the added length for 15m will be shorter than it would be without the trap. There's a whole raft of design approaches about where you put the resonance relative to the frequencies of use, and how you want the current distribution to work, and then there's all the "what's practical to make and manufacture" and "tolerance to misadjustment/weather/aging". You can get a pretty good start with a modeling code like NEC, but eventually, you've got to go out and start fiddling in real life, because almost all traps are not precisely modeled by NEC for a variety of reasons. In the manual of the CWA-840, each leg of the 7MHz section, is 11.1meters in lenght , wich, it seems to me, that it is rather longer that 1/4 wave. (10.1m). Why ? See above. Thanks a lot for your answers CWA-840: -----[ ]-------------ooo--//-- 2.3m coil 11.1m balun The trap is probably self resonant below 40m... but that is just a guess from experience of having designed such things. Owen |
Trap antenna
___Original Message_________________________________________
From: Jim Lux Date: Mon, 24 Oct 2011 Time: 10:21:41 Say you want an antenna that covers both 10m and 15m. You start with a 10 meter resonant antenna. Now hook a trap which has very high impedance at 10m on the end of it. Since it's high Z, not much current flows, so it doesn't change the 10m behavior very much. But, you also want it to work at 15m. So you figure out how long an additional element you need to put "outboard" of the trap to get the system to resonate. Typically, the trap is a parallel LC, so below resonance, it looks somewhat inductive. Since a short element looks capacitive, the added length for 15m will be shorter than it would be without the trap. There's a whole raft of design approaches Hi béo-master Here is a simple trap antenna design tool that I have successfully used a few times: http://www.k7mem.150m.com/Electronic_Notebook/antennas/shortant.html -- 73 Ian, G3NRW The AIM4170 Antenna Analyzer: http://homepage.ntlworld.com/wadei/aim4170.htm |
| All times are GMT +1. The time now is 05:59 AM. |
Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
RadioBanter.com