I want to use galvanized water pipe as an antenna support, and wonder where
I can get the heavy duty mast supports (standoffs from the side of a house)
to accommodate say a 1.5" mast.
You can reach me at .
Thanks for any help.
73,
Richard
K1TAV

"genev" wrote in message
news:%Ue6e.1012$5J3.358@lakeread01...
I want to use galvanized water pipe as an antenna support, and wonder
where
I can get the heavy duty mast supports (standoffs from the side of a
house)
to accommodate say a 1.5" mast.
You can reach me at .
Thanks for any help.
73,
Richard
K1TAV


Radio Shack carries two different sizes of stand-off from the eave of a
house to a 1.5 to 2" mast.

Jack

On Sun, 10 Apr 2005 18:15:39 -0400, "Jack Painter"
wrote:


"genev" wrote in message
news:%Ue6e.1012$5J3.358@lakeread01...
I want to use galvanized water pipe as an antenna support, and wonder
where
I can get the heavy duty mast supports (standoffs from the side of a
house)
to accommodate say a 1.5" mast.
You can reach me at .
Thanks for any help.
73,
Richard
K1TAV


Radio Shack carries two different sizes of stand-off from the eave of a
house to a 1.5 to 2" mast.

Jack


In the past I've used the Radio Shack wall stand-offs with a section
of galvanized 1.5" water pipe, and that worked fine to support an R-5
vertical, but the pipe is heavy and needs to be ground-supported, as
Tam inferred.

bob
k5qwg

"genev" wrote in message
news:%Ue6e.1012$5J3.358@lakeread01...
I want to use galvanized water pipe as an antenna support, and wonder where
I can get the heavy duty mast supports (standoffs from the side of a
house)
to accommodate say a 1.5" mast.
You can reach me at .
Thanks for any help.
73,
Richard
K1TAV


Richard,
You are going to run the pipe all the way to the ground, aren't you?

Tam/WB2TT

Hi all, and thanks for the info.
Yes, the mast will go from the ground up! I thought about some sort of a
hinge at the base, but sounds too complicated, so will just pull it up from
an upper story window.
Of course, and advice is greatly appreciated.
Richard
K1TAV

Not only will having the base grounded make it more
stable, it also provides a much better return to earth if
you take a spark. Providing you ground the base well,
anyway... It acts as a lightning rod.
So you want to ground it like one.
You could make a hinge. Some use a tower section,
and adapt the holes, thrust bearings, etc to fit a mast.
You could also weld a heavy plate, etc, with a short
pipe stub to fit masts into. That could be hinged to a base
plate. I have a tower that is set up this way. It's tilt over at
the base, and also crank up...The base and hinge part
was made down at the shipyard using ship steel.
*Very* heavy duty...The pieces were cut out on a CRC
plasma table that they cut pieces of ship steel on...
The thing will stand up by itself in the middle of a field,
even with the tower raised, and the beam on it, with no guys...
But I guy it to be safe...I've been taking it to field days the
last few years..I've got "drive on" mast holders that were
made from the same heavy stuff. You could rig one of those
to hinge on a baseplate no problem. MK

sounds interesting! If I can find a decent welder around here I would
consider doing that. Looks like this will be a summer project anyway, as
not much time until then.
Richard
K1TAV