16 el coaxial colinear (2.4ghz) question - How 'bout this?
 

"Bob Bob" wrote in message
...
Hi Ken

Note when I modeled the 16 element I did so as a series of dipoles fed
in phase rather than use the coax/crossover design.

I felt like checking your statement about being unable to receive in the
front yard. At around 45 degrees down from the antenna the NEC2 output
says that you'll get a lobe between 20 and 30dB down from an isotropic
(or 35-45dB down from the max gain) I'll admit my near close in signal
theory doesnt really exist but a path of 800m has about 106dB of loss.
If you knock that back to 12 metres (6dB every time you halve) you have
about 70dB path loss. If you then take a WAP kind of power level of
around 10dBm the RX signal at 12m with a halve wave is going to be
around (10-70-25) -85dBm. This kind of corelates with the lowest usable
signal for WiFi! There ya go!

I like the URL you sent as being more predictable/easier to construct
that using bits of coax. Keep in mind that progressively longer and
longer colinears are more and more critical to build and the
construction method that is being used is not really optimal in the area
of spacing between elements. You could probably pick a much better
design. I think however that you need to sit back and consider what you
are trying to achieve. Are you setting up a personal WiFi LAN for others
to use or just for specific contacts? If you are wanting to work in one
direction (or use a rotator) it might be more effective to use a corner
reflector and maybe 4 elements in phase. This will be much less critical
in construction. Remoting the WAP will make a lot of sense too as
you'll lose the line loss! Comments?

Cheers Bob


That's great info, Bob - btw my router puts out +20dbm and the
background noise level in the receiver @ 2.422ghz is -97dbm +/-
2-3db....

As far as my purpose, I'm trying to get access when I go to a park
to go /p on 40m. I want to be able to access the DX cluster &
HF Pack users as well as check e-mail.

I did a little research and the antennas I bought on eBay are 7dbi
gain with, of course no feedline losses. No matter how much I
crunch the numbers, I just can't find a more cost effective system.

Ken KG0WX

16 el coaxial colinear (2.4ghz) question - How 'bout this?
 

Hi Ken

Well if you are going to a specific location (the park) you may as well
use a directive antenna like a corner reflector/gridpack etc. In fact
you could be real smart and use a 2m handheld and a low data rate link
to swing the antenna in whatever direction you choose (eg packet talking
to a home PC, PC connected to rotator. You could even make it as simple
as a two state tone decoder for CW or CCW the antenna whilst watching
the WiFi signal) There are some quite broad reflector based designs out
there that give good gain on 2.4GHz. For example a 900x700mm gridpack
will give you about 25dBi.

I guess you are using one of the amateur radio 2.4GHz channels? You can
use a higher EIRP than the normal WiFi is limited to. (from memory 30dBm
EIRP is the legal max for unlicensed use) You do need to identify
though. (A simple text based ping might be enough)

I am surprised at the -97dBm sensitivity. The links I worked on in the
past we used -87 for 11MB 802.11b predictions. I guess your figure would
be at the lowest data rate and thus effective bandwidth. You can't beat
Boltzmann! The Ethernet microwave data radios I work with nowadays need
about 20-25dB s/n for a 50MB/sec channel that covers about 10MHz b/w.
Thermal noise in 10MHz is about -103dBm so we need better than -83 for a
good path. Our radios dont change speeds/bandwidth on the fly though.
Interference will be your greatest enemy though...

One of you other posters suggested remoting the router box to remove the
cable loss problem. It is the place where most of your problems lie.
Even moving it part the distance will help. You might also look at a
better coax. We use to use LMR400 extensively. It was much cheaper than
RG213 and lower loss as well.

Oh and be careful with the WAP etc setup as regards "maximum distance".
We had a problem early on where we left it at the default for a 10km
path and the ACKs (or something) kept crashing and kept the speed down.
The distance number introduces some kind of ACK delay..

Good luck!

Cheers Bob VK2YQA

Ken Bessler wrote:


That's great info, Bob - btw my router puts out +20dbm and the
background noise level in the receiver @ 2.422ghz is -97dbm +/-
2-3db....

16 el coaxial colinear (2.4ghz) question - How 'bout this?
 

"Bob Bob" wrote in message
...
Hi Ken

snip

I am surprised at the -97dBm sensitivity.

snip

Yea, it's a genuine Atheros card, not just an Atheros chipset. I bought it
based on reports online touting it's high reciever performance and the
fact that it is a mini PCI card, not a pcmcia card.


One of you other posters suggested remoting the router box to remove the
cable loss problem. It is the place where most of your problems lie.
Even moving it part the distance will help. You might also look at a
better coax. We use to use LMR400 extensively. It was much cheaper than
RG213 and lower loss as well.

That is what I was using - 40' of it.


Oh and be careful with the WAP etc setup as regards "maximum distance".
We had a problem early on where we left it at the default for a 10km
path and the ACKs (or something) kept crashing and kept the speed down.
The distance number introduces some kind of ACK delay..

Good luck!

Cheers Bob VK2YQA

Thanks for all the help, Bob - 73!

Ken KG0WX

16 el coaxial colinear (2.4ghz) question - How 'bout this?
 

I tried to make the same antenna with 1/2" hardline & had several RF
analyzers to help me, it never worked out. This article helps
explain why coax wont work, I used wire and would my on coils for
phasing, i also took apart a Madrax antenna to get the measurements,
they used brass tubes inbetween the coils, not because its brass but so
the 1/2 wave length can be easily adjusted.
http://www.centurion.com/home/pdf/wp_omni_wireless.pdf

16 el coaxial colinear (2.4ghz) question - How 'bout this?
 

wrote in message
ups.com...
I tried to make the same antenna with 1/2" hardline & had several RF
analyzers to help me, it never worked out. This article helps
explain why coax wont work, I used wire and would my on coils for
phasing, i also took apart a Madrax antenna to get the measurements,
they used brass tubes inbetween the coils, not because its brass but so
the 1/2 wave length can be easily adjusted.
http://www.centurion.com/home/pdf/wp_omni_wireless.pdf

Hi Tucker

Thanks for reference to that great site. I really like that flat antenna.

Jerry