LinkBack Thread Tools Search this Thread Display Modes
Prev Previous Post   Next Post Next
  #6   Report Post  
Old June 26th 08, 08:47 PM posted to rec.antiques.radio+phono,rec.radio.amateur.boatanchors
external usenet poster
 
First recorded activity by RadioBanter: Feb 2007
Posts: 45
Default A gallery of gassy tubes

On Jun 26, 1:58*pm, "Richard Knoppow" wrote:
"BH" wrote in message

...
On Jun 25, 7:12 pm, wrote:

The following web page shows several photos of vacuum
tubes that glow
because they’re either gassy or induce florescence in the
their glass
bulbs. Although the English is a little choppy, the
narrative and
pictures are informative:


http://www.jacmusic.com/html/article...w/blueglow.htm


The author claims he’s revived gassy tubes by re-heating
the getters.
Has anyone tried this?


-Dave Drumheller, K3WQ


Sounds like hog wash. No blue or blue in tubes is probably
normal.
Magenta is probably gas.

* * *Its very common to see a blue glow on the envelope when
there is fairly high voltage on the tube. I've forgotten the
mechanism but its not gas. Gas can cause a glow between
elements.
* * *AFAIK, there is no way to re-flash the getter.

--
---
Richard Knoppow
Los Angeles, CA, USA


Two comments.
1) I do recall certain 807s in the intermediate stages of a WWII
transmitter that exhibited blue fluorescence of the glass envelope due
in IMO to electrons missing the plate/anode and striking the glass.
Say this because one could see a definite pattern of the electrode
structure in the fluorescence of the glass, rather like sunlight
shining through a patterned window onto a wall or floor. It was not
just a 'fuzzy' indistinct glow! These 807s were fine and worked
perfectly as drivers and modulators to the final/PA.
A 'soft' or 'gassy' tube on the other hand would have a glow inside
its electrode structure; rather similar to a gas voltage regulator
tube; such as an OD3 VR150 etc.
2) It MIGHT be possible to get rid of gas in a tube by reheating the
getter; there might be active 'getting' material left? No expert on
tube manufacture but understand those getters were heated by RF. So
could be done again?
Whether the gas has leaked in over the years or is residual gas from
original rushed manufacture during say war time conditions might also
be a factor? If air leaks into the tube albeit slowly over many years
it may continue to do so? Although using the tube (i.e. hot) may
discourage (slow down) or encourage (hasten) that?
002 from here.
Newfoundland; where in Dec. 1901 Marconi received the first
Transatlantic wireless telegraph message!
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Atique Photo Gallery [email protected] Shortwave 0 November 16th 07 10:44 AM
Indian Rape Gallery MarQueerMyDear Policy 2 November 15th 06 11:10 PM
Tube failure mode: gassy? [email protected] Homebrew 21 June 25th 06 03:23 PM
Rogues' Gallery - new additions Bill Antenna 1 September 23rd 03 05:46 AM


All times are GMT +1. The time now is 02:11 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017