About Us

Gary P. Fiber · October 3rd 06, 03:54 AM posted to rec.radio.amateur.equipment

On 1 Oct 2006 14:26:54 -0700, wrote:

I would like to repair an Icom 735 that is not able to receive from 4
to 11 MHz. Two diodes (D11 & D13) in the receive bandpass filter
section are blown (due to operation near another high power
transmitter/antenna).

These diodes are on the main board which can be accessed by removing
the bottom cover. However they can only be replaced by
unsoldering/soldering on the bottom of the main board. I have several
questions for anyone who has made repairs to this rig:

1. It is easy to remove the screws holding down the board but there is
extensive wiring connected to this board. Does the board have to be
totally removed in order to get at this area? How difficult is this
job? Any tips or tricks you might recommend?

2. The diodes are 1ss53 which is a Japanese switching diode. They are
hard to find. Has anyone found a direct replacement for this part that
gives equal or better performance? (I do not want to change any of the
bias resistors).

Thanks - Roger

The board is not that hard. YES there will be cables you will need to
disconnect. Have your digital camera handy or just a paper and pencil
and make a quick sketch of the board I used to do that before the
camera says and sometimes its still easier than photos. When
disconnecting multi pin connectors, pick on end and mark the wire
color so you will get the connector reinstalled correctly.

I think one coax gets disconnected that goes through the from of the
735. There is an other or so too that you will see get tight as you
try to life the board so disconnect it too. Just don't get then
confused, maybe take a moment and mark them with masking tape.

Basically you will unscrew to board. Now with the front of the radio
towards you gently lift the front of the circuit board. " walk " the
board towards the front lifting it above the front of the radio.

You are working towards getting the rear connectors out of the back
panel and clear of the rear lip. PAY attention to any cables that need
removing and do so as you go.

Once the rear connectors are clear of the rear chassis lip you can
then flip the back edge of the circuit board up and over to get to the
diode solder joints.

Its really easier than this write up sounds. I have talked several
through it over the telephone as you need to do the same thing to
install the CW filter.

Over the years many have tried substituting those diode, even to
installing pin diodes. While I was at Icom tried them at Icom and
found no performance enhancement. We had one person remove and replace
his band pass filter diodes with pin type and we could not fix that
rig. We even installed original diodes back into it. It was an IC-751.

Call Icom's parts department for the diodes. Another source of
Japanese parts used to be MCM audio

Gary K8IZ

Thread Tools	Search this Thread
Show Printable Version	Search this Thread: Advanced Search
Display Modes
Switch to Linear Mode Switch to Hybrid Mode Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Useful Icom IC-R75 [R-75] Links for Facts and Information about the Icom IC-R75 [R-75]	RHF	Shortwave	1	January 3rd 05 08:56 AM
Last Day For Secret Icom Sale R-75 $425	Lucky	Shortwave	6	October 17th 04 09:41 AM
SECRET ICOM SALE: R-75 $425 w/ DSP and Free shipping	Lucky	Swap	13	October 16th 04 10:57 PM
Last Day For Secret Icom Sale R-75 $425	Lucky	Swap	0	October 16th 04 10:45 AM
SECRET ICOM SALE: R-75 $425 W/ DSP AND FREE SHIPPING	Lucky	General	0	October 15th 04 03:02 AM

Menu

About Us