Mike wiring for Icom IC-725
Would someone please give me the wiring for the Icom IC-725. Also ACC1
wiring if possible. I have misplaced my manual. Tnx de WN5GDV |
Bill, the following should help.
Front panel view of 8 pin chassis mic connector. Indent located at 12o'clock position, working anti-clockwise. Pin 1=Mic input Pin 2=+8v @10mA dc output Pin 3=Freq up/down (Ground direct for up, or via 470 ohm) Pin 4=Squelch switch (open=low,closed=high) Pin 5=PTT Pin 6=Gnd (PTT) Pin 7=Gnd (Mic ground) Pin 8=AF output (Middle pin) Icom warning, do not short Pin2 to gnd. Damage to 8v regulator will occur. Taken from Icom manual good luck, Roger G7JAQ PS, for MIKE read MIC -- ---------------------------------------------------- This mailbox protected from junk email by Matador from MailFrontier, Inc. http://info.mailfrontier.com |
Bill, the following should help.
Front panel view of 8 pin chassis mic connector. Indent located at 12o'clock position, working anti-clockwise. Pin 1=Mic input Pin 2=+8v @10mA dc output Pin 3=Freq up/down (Ground direct for up, or via 470 ohm) Pin 4=Squelch switch (open=low,closed=high) Pin 5=PTT Pin 6=Gnd (PTT) Pin 7=Gnd (Mic ground) Pin 8=AF output (Middle pin) Icom warning, do not short Pin2 to gnd. Damage to 8v regulator will occur. Taken from Icom manual good luck, Roger G7JAQ PS, for MIKE read MIC -- ---------------------------------------------------- This mailbox protected from junk email by Matador from MailFrontier, Inc. http://info.mailfrontier.com |
Bill,
info on ACC(1) 8pin din, rear mounted socket as follows Indent (ground) located at 12 o'clock. Rear panel view. Working clockwise from indent. Pin 6=D=Squelch input. Pin 1=No connection. Pin 4=A= Screened AFSK Input. Pin 2=B=AFSK Screen gnd. Pin 5=C=AF Input. Pin 3=E=PTT. Pin 7=No connection. regards, Roger, G7JAQ -- ---------------------------------------------------- This mailbox protected from junk email by MailFrontier Desktop from MailFrontier, Inc. http://info.mailfrontier.com |
Bill,
info on ACC(1) 8pin din, rear mounted socket as follows Indent (ground) located at 12 o'clock. Rear panel view. Working clockwise from indent. Pin 6=D=Squelch input. Pin 1=No connection. Pin 4=A= Screened AFSK Input. Pin 2=B=AFSK Screen gnd. Pin 5=C=AF Input. Pin 3=E=PTT. Pin 7=No connection. regards, Roger, G7JAQ -- ---------------------------------------------------- This mailbox protected from junk email by MailFrontier Desktop from MailFrontier, Inc. http://info.mailfrontier.com |
Bill Murcheski wrote:
Would someone please give me the wiring for the Icom IC-725. Also ACC1 wiring if possible. I have misplaced my manual. Tnx de WN5GDV Hello, Bill. You can download the manual as a PDF by following the link at http://www.icom.co.jp/world/products/amateur/index.htm HTH -- To design the perfect anti-Unix, write an operating system that thinks it knows what you're doing better than you do. And then adds injury to insult by getting it wrong. - esr |
Bill Murcheski wrote:
Would someone please give me the wiring for the Icom IC-725. Also ACC1 wiring if possible. I have misplaced my manual. Tnx de WN5GDV Hello, Bill. You can download the manual as a PDF by following the link at http://www.icom.co.jp/world/products/amateur/index.htm HTH -- To design the perfect anti-Unix, write an operating system that thinks it knows what you're doing better than you do. And then adds injury to insult by getting it wrong. - esr |
All times are GMT +1. The time now is 01:43 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
RadioBanter.com