Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Old October 14th 03, 07:28 PM
Mike W
 
Posts: n/a
Default simple diode switching query

ok folks..
I'm getting a headache thinking about this so I'm passing it to you
lot for 'peer review' while I go to the pub ... I forsee pints of
luverly bitter.

http://www.qsl.net/g8nxd/diodesw.gif ( 8k )

describes a train of thought.. Am I having an abberation here or will
it work as I intend?.

ie. switch between the IF strip on RX and MOD source on TX and route
relevant signals IN/OUT of the filter and mixer in the correct way.

Obviously blocking C's are not shown

cheers Mike W
  #2   Report Post  
Old October 15th 03, 04:31 AM
 
Posts: n/a
Default



Mike W wrote:

ok folks..
I'm getting a headache thinking about this so I'm passing it to you
lot for 'peer review' while I go to the pub ... I forsee pints of
luverly bitter.

http://www.qsl.net/g8nxd/diodesw.gif ( 8k )

describes a train of thought.. Am I having an abberation here or will
it work as I intend?.

ie. switch between the IF strip on RX and MOD source on TX and route
relevant signals IN/OUT of the filter and mixer in the correct way.

Obviously blocking C's are not shown

cheers Mike W


I can't see a receive path from the antenna through the
circuit to the if amp. - looks like the back to back diodes
on the right side of the mixer block the path. On TX,
I can't find a path from the DSB sig to get to the input
of the mixer - the back to back red diodes block that.
  #3   Report Post  
Old October 15th 03, 04:31 AM
 
Posts: n/a
Default



Mike W wrote:

ok folks..
I'm getting a headache thinking about this so I'm passing it to you
lot for 'peer review' while I go to the pub ... I forsee pints of
luverly bitter.

http://www.qsl.net/g8nxd/diodesw.gif ( 8k )

describes a train of thought.. Am I having an abberation here or will
it work as I intend?.

ie. switch between the IF strip on RX and MOD source on TX and route
relevant signals IN/OUT of the filter and mixer in the correct way.

Obviously blocking C's are not shown

cheers Mike W


I can't see a receive path from the antenna through the
circuit to the if amp. - looks like the back to back diodes
on the right side of the mixer block the path. On TX,
I can't find a path from the DSB sig to get to the input
of the mixer - the back to back red diodes block that.
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Simple practical designing with antenna modeling programs Richard Antenna 4 June 11th 04 02:19 AM
Remote antenna switching J M Noeding Antenna 2 May 22nd 04 05:17 PM
T2FD modded to add LF, no switching, AM BC rejection SpamLover Antenna 0 November 7th 03 02:59 PM
Need Source for Diode in TS-1285/URM-120 Wattmeter 2-30 MHz Plug-in Sensor, pls David J. Windisch Equipment 6 July 8th 03 05:15 PM
Need Source for Diode in TS-1285/URM-120 Wattmeter 2-30 MHz Plug-in Sensor, pls David J. Windisch Equipment 0 July 8th 03 12:20 AM


All times are GMT +1. The time now is 04:50 AM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017