DAVE,

So you have a Sangean ATS -505 and your 'problems' are Antenna
Overload and Noise Levels.
* Consider a 'smaller' shorter Antenna will reduce the overload problems.
* Consider a Low Noise Antenna Design will reduce the noise problems.
{LOW NOISE SWL ANTENNA - popularized by John Doty}
http://groups.yahoo.com/group/Shortw...enna/message/2
http://www.anarc.org/naswa/badx/ante...e_antenna.html

For a simple 'external' Shortwave Antenna to use with the Sangean
ATS-505 'portable' Shortwave Radio, using the 1/8" Mono-Jack
External Shortwave Antenna Input. Consider a Random Wire
Antenna using a Matching Transformer and Ground for Low Noise
and Wide Range Frequency Coverage.

PARTS: Here is a simple SWL Antenna Idea using a few common
RadioShack TV Antenna type parts:
Catalog #: 15-1174 = 25~50 Foot 300 Ohm (Flat) TV Twin-Lead
Catalog #: 15-1230 = 75 to 300 Ohm Matching Transformer (2 Ea.)
Catalog #: 274-286 = 1/8" Mono (Phone) Plug
Catalog #: Catalog #: 15-1579 = 25~50 Foot Coax Cable with F Connectors

NOTE: This is an 'improved' Random Wire SWL Antenna using "TV"
Parts for 'reducing' Man Made Noise (RFI EMF) that is generated in
or near most modern homes/buildings.

EXTERNAL "OUTSIDE" SWL ANTENNA:

The Antenna [Loop] Element is Stretched outside Horizontally or
in the shape of an Inverted "L". The Antenna [Loop] Element is
formed by connecting the two ends of the Far-End of the 300 Ohm
TV Twin Lead. This forms a continuous single skinny horizontal
flat loop going out and back. This also represents a Balance
300 Ohm Load to match-up with the 300 Ohm Matching Transformer.
The 300 Ohm Leads of the Matching Transformer connects to the
Near-Ends of the Loop Antenna Element. The 75 Ohm F Connector
of the Matching Transformer is connected to the 75 Ohm Coax Cable.
The 75 Ohm Coax Cable acts as the Lead-In from the Outside to
inside the house to the radio shack. The other end of the 75
Ohm Coax Cable is connected to the 75 Ohm F Connector of the
Matching Transformer. The Radio-End of the Coax Cable F Connector
would connect to a 75 to 300 Ohm Matching Transformer; and then
into a 1/8" Mono-Plug to plug into the Radio.
NOTE: Using the 300 Ohm TV Twin Lead in a Skinny Flat Loop
Antenna should balance-cancel-reduce most man made noise and be
Omni-Directional.

GROUND: Find a Grounding Point within/about your dwelling.
Secure a good Grounding Point for your Radio and Antenna.
Run a Heavy & Short Ground Wire to your Radio. Locate the
Ground Terminal on your Radio. Attach/Secure the Ground Wire
to the Coax Cable and/or the Radio's Ground Terminal.

FWIW: This Antenna using common TV Antenna type parts should
be effective as SWL Antennas above 5MHz and beyond 30MHz.


iane ~ RHF
..
Some Say: On A Clear Day You Can See Forever.
http://groups.yahoo.com/group/Shortw...na/message/502
I BELIEVE: On A Clear Night...
You Can Hear Forever and Beyond - The Beyond !
..
..
= = = "Dave" wrote in message
= = = ...
I recently hooked up a thirty-six foot (plus or minus a couple of feet)
piece of four-stranded wire with alligator clip to the internal "whip"
antenna of my portable shortwave receiver, for the extra performance such a
device offered. It works so well that I now cannot usually use my "DX"
setting because of all the background noise (sounds like hundreds of other
broadcasts vying for attention.) I don't know the frequency source of all
this background noise, but would like to filter out as much of it as I can.
One manufacturer of a similar "wind-up" antenna adds a capacitor to the wire
in order to lower the resonance frequency of the wire. If I were going to
try something similar (adding a capacitor, in series) in an attempt to bring
the resonance of the wire down into the 30 MHz range, what size (roughly)
capacitor should I use? Should I just try a few with different ranges, or
does anyone here have any suggestions?

TIA

Cross-posted between sci.electronics.basics and rec.radio.shortwave


Dave


..