On Fri, 10 Jan 2014 19:36:59 -0500, Jerry Stuckle
wrote:
The main loss in a connector is due to the impedance bump at the
connector. This can be easily seen on a TDR (Time Domain Reflectometry)
display.
Rubbish. Let's pretend that I mix in a 75 ohm coax connector into a
50 ohm system. Depending on the location of this "impedance bump",
the VSWR is no more than 1.5:1 which is generally considered marginal.
That's 0.18dB of mismatch loss.
http://www.microwaves101.com/encyclopedia/calvswr.cfm
If you're doing satellite or microwave DX work, then 0.18dB might be
important. However, for most other applications, it's a trivial
amount.
You might be amused to know that most of my rooftop antennas are fed
with 75 ohm coax and that my favored antenna designs are also 75 ohm.
There are various reasons, but the main one is that coax cable losses
are less at 75 ohms, than at 50 ohms. 50 ohms can handle more power,
but 75 ohms has less loss.
http://www.belden.com/blog/broadcastav/50-Ohms-The-Forgotten-Impedance.cfm
The only problems I have with 75 ohms is finding the proper connectors
and dealing with the pads needed to make my 50 ohm test equipment look
like 75 ohms. (Actually the real reason is that the 75 ohm stuff is
mostly CATV surplus, which tends to be really cheap).
Mo
http://www.qsl.net/n9zia/wireless/75_ohm_hardline.html
Some connectors are better than others; for instance, the older F
connectors which are crimped down with a ring are the worst. Next is
the connector where the crimp is a hex crimp - it doesn't give a
consistent impedance around the connector.
I rip those out wherever I find them, even if they're on the ends of
commercially crimped cables (usually RG-59/u which is another
nightmare). However, the loss mechanism with the old CATV coax and
associated crappy crimp connectors was radiation, not mismatch loss.
The ground connections would fall apart, turning the coax shield into
an impressive antenna.
The best (and the ones we use) compress the entire base of the connector
evenly, creating a smooth crimp. The end of the coax is evenly covered
by the connector.
I've had problems with some of those push-on connectors. I also don't
want to stock a zillion different connector variations from different
vendors. So, I've standardized on the "red" univeral T&B SNS1P6U
RG-6/u connectors:
www.ebay.com/sch/i.html?_nkw=SNS1P6U
The other problem is the technician installing the connectors. I've
seen great ones, and not-so-great ones. There are a lot of chances for
going wrong - for instance, it's easy to screw up the braid when trying
to insert a crimp-on connector under the outer jacket and shield. And
soldering connectors (i.e. PL-259 and N) is almost sure to give you a
huge bump (and loss) because it's almost impossible to solder the shield
without melting the inner insulator to some point. It may not short
out, but that doesn't mean you don't have loss there.
Actually, it's not the crimp job that kills the connection. It's the
stripping of the coax that causes the most problems. I use various
rotary contrivances that have razor blades to make the cuts at the
correct spacing. Those work well initially, but after about 50
connectors, the blades become dull and useless. Of course, nobody has
spare blades or knows how to adjust them. They either continue to use
a dull razor or steal my new stripper.
Oops... dinner... gone.
--
Jeff Liebermann
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060
http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558