![]() |
|
2 meter yagi
Who sells them with the most bang for the buck?
|
2 meter yagi
Depends what you want. Are you going to use a small Yagi for FM work or
a long boom Yagi for SSB/CW? If you want something fairly simple, a homemade 6 or 8 element Yagi is fairly simple. Otherwise, for some serious weak signal work, the K1FO designs are quite commonly used. Directive Systems sell them... http://www.directivesystems.com/antenna4.htm Hope that helps! Scott N0EDV Merlin-7 KI4ILB wrote: Who sells them with the most bang for the buck? |
2 meter yagi
What design plans would you use?
Thanks joe "Scott" wrote in message .. . Depends what you want. Are you going to use a small Yagi for FM work or a long boom Yagi for SSB/CW? If you want something fairly simple, a homemade 6 or 8 element Yagi is fairly simple. Otherwise, for some serious weak signal work, the K1FO designs are quite commonly used. Directive Systems sell them... http://www.directivesystems.com/antenna4.htm Hope that helps! Scott N0EDV |
2 meter yagi
"Merlin-7 KI4ILB" wrote in message
... What design plans would you use? Thanks joe Are you an Internet only type of person? The original design was perfected by Steve Powlishen, K1FO, who spent hundreds of hours optimizing yagi designs on a high powered Hewlett Packard computer. He started with some computer optimized designs of Tom Kirby, W1EJ, (SK) who was using computer software developed at Ohio State University. W1EJ had came up with many excellent VHF long yagi designs. The finished K1FO designs were carefully checked out in the real world by K1FO to ensure accuracy of the design effort. His efforts have produced an exceptional design with maximum gain very close to the maximum amount possible, while keeping side lobes, (particularly those of the H-plane) at a very low level. The net result is broad bandwidth, wide beamwidth, and clean lobe structure. Clean H-plane patterns translate to efficient stacking with maximum possible gain and manageable array side lobes. The design has been published in MANY printings of the ARRL Handbook. gb |
2 meter yagi
"Scott" wrote in message .. . Depends what you want. Are you going to use a small Yagi for FM work or a long boom Yagi for SSB/CW? If you want something fairly simple, a homemade 6 or 8 element Yagi is fairly simple. Otherwise, for some serious weak signal work, the K1FO designs are quite commonly used. Directive Systems sell them... http://www.directivesystems.com/antenna4.htm Hope that helps! Scott N0EDV Now you tell me. I just ordered 2 beams from M-Square, one for 432 and one for 144. Wish I had the K1FO antennas as I had one for 432 and it worked very well. I did not know anyone had picked up the K1FO design after he became a SK. |
2 meter yagi
Ralph Mowery wrote:
"Scott" wrote in message . .. Depends what you want. Are you going to use a small Yagi for FM work or a long boom Yagi for SSB/CW? If you want something fairly simple, a homemade 6 or 8 element Yagi is fairly simple. Otherwise, for some serious weak signal work, the K1FO designs are quite commonly used. Directive Systems sell them... http://www.directivesystems.com/antenna4.htm Hope that helps! Scott N0EDV Now you tell me. I just ordered 2 beams from M-Square, one for 432 and one for 144. Wish I had the K1FO antennas as I had one for 432 and it worked very well. I did not know anyone had picked up the K1FO design after he became a SK. Important correction: Steve Powlishen, K1FO, is NOT an SK! (W9GB had it correct: the person who died was the co-developer W1EJ.) W9GB is also correct that they are excellent yagis, and have been published in several editions of the ARRL Handbook. The most extensive write-up is in the ARRL Microwave Experimenter's Handbook Volume 1. Don't worry, you'll be fine with an M2 yagi as well. There is a lot of convergence between modern long yagi designs, so the state-of-the-art is that products from all the major manufacturers are very close to optimum performance in terms of gain and pattern. There can still be some differences in performance between different brands, depending mostly on the exact balance between gain, pattern and bandwidth the designer was trying to achieve. However, these differences between brands are almost always quite small, so for comparable designs (ie yagis with the same or very similar boom length, of 2-3 wavelengths or more) the difference between brands might only be a few tenths of a dB in terms of gain, and maybe a few dB difference in the levels of minor sidelobes. End users will hardly ever notice these differences on the air, so when choosing which long yagi to buy, you can pay more attention to other important factors, such as overall size, style of construction, suitability for your weather conditions, price and dependable product support. [I could write a lot more about "optimized" long yagis, but not this morning. There's more information in the 'Long Yagi Workshop' section of my website.] -- 73 from Ian GM3SEK http://www.ifwtech.co.uk/g3sek |
2 meter yagi
If you don't mind having a little less gain than is ultimately possible
by using an antenna modeling program, the NBS (Nation Bureau of Standards) designs are pretty straight-forward. For a 6 element Yagi, here is element lengths and spacings for building with insulated elements (insulated from the boom, so I would use wood, 1" X 2" X 8.5') Lengths: Reflector = 3' 4" Driven = 3' 2-3/16" Dir 1 = 3' 7/8" Dir 2 = 3' 7/16" Dir 3 = 3' 7/16" Dir 4 = 3' 7/8" Spacing: Ref to Driven = (187.2/Fc) X 12 Spacing between all other elements = (234/Fc) X 12 where Fc is the design center frequency in MHz, ie 146 for the center of the FM portion). The spacing calculations give the answer in inches. Then you need to feed it. I use delta matches. Are you good at qrz.com? If so I can send you a drawing of the feed to get you started (but you would need an SWR meter that works at 2M to get it adjusted). Scott N0EDV Merlin-7 KI4ILB wrote: What design plans would you use? Thanks joe "Scott" wrote in message .. . Depends what you want. Are you going to use a small Yagi for FM work or a long boom Yagi for SSB/CW? If you want something fairly simple, a homemade 6 or 8 element Yagi is fairly simple. Otherwise, for some serious weak signal work, the K1FO designs are quite commonly used. Directive Systems sell them... http://www.directivesystems.com/antenna4.htm Hope that helps! Scott N0EDV |
2 meter yagi
Oops, sorry ;(
I think the M Squared antennas are pretty good anyways. Scott N0EDV Ralph Mowery wrote: "Scott" wrote in message .. . Depends what you want. Are you going to use a small Yagi for FM work or a long boom Yagi for SSB/CW? If you want something fairly simple, a homemade 6 or 8 element Yagi is fairly simple. Otherwise, for some serious weak signal work, the K1FO designs are quite commonly used. Directive Systems sell them... http://www.directivesystems.com/antenna4.htm Hope that helps! Scott N0EDV Now you tell me. I just ordered 2 beams from M-Square, one for 432 and one for 144. Wish I had the K1FO antennas as I had one for 432 and it worked very well. I did not know anyone had picked up the K1FO design after he became a SK. |
2 meter yagi
"Merlin-7 KI4ILB" wrote in message ... Who sells them with the most bang for the buck? Probably CushCraft. There are so many of these around that they are also not hard to find used at hamfests. I once picked up a 7 element for $8. Can't buy the aluminum for that. A friend of mine used 4 of their Boomer models for moon bounce. Only thing I don't like about them is the gamma match. Tam/WB2TT |
2 meter yagi
Very pleased with my M2 2M9SSB 9 element yagi. 12.4 dbi gain with 20+db
f/b. Download the owners manual he 1. http://www.ad5th.com/VHF.html -- 73,Charlie-AD5TH www.ad5th.com " Tam/WB2TT" wrote in message . .. "Merlin-7 KI4ILB" wrote in message ... Who sells them with the most bang for the buck? Probably CushCraft. There are so many of these around that they are also not hard to find used at hamfests. I once picked up a 7 element for $8. Can't buy the aluminum for that. A friend of mine used 4 of their Boomer models for moon bounce. Only thing I don't like about them is the gamma match. Tam/WB2TT |
All times are GMT +1. The time now is 05:22 PM. |
|
Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
RadioBanter.com