LinkBack Thread Tools Search this Thread Display Modes
Prev Previous Post   Next Post Next
  #22   Report Post  
Old August 30th 07, 11:11 AM posted to rec.radio.amateur.antenna
external usenet poster
 
First recorded activity by RadioBanter: Dec 2006
Posts: 1,169
Default Sun noise

Jim Lux wrote in news:46D463CF.1080309
@jpl.nasa.gov:

Dave Oldridge wrote:
Owen Duffy wrote in news:Xns999955EE72868nonenowhere@
61.9.191.5:


Dave Oldridge wrote in
.159:


Near as I could measure it, the NF of the receiver after my mod was
1.2db. I had to resort to boiling and freezing water and a tiny

dummy
load to measure it at all.

snip


This

still demands high resolution measurement of noise power.



Yes, anything less than 4 digits is just about useless.


That would be necessary but not sufficient.

....

Just following through on the '4 digit' issue...

I have done two series of 250 measurements of audio noise voltage from a
SSB receiver using two different digital multimeters, the 9932 is a
modern digital multimeter that is NOT true RMS responding, and the 506 is
a modern digital multimeter that is true RMS responding with bandwidth
adequate to cover the receiver output response.

From observation with a stopwatch, I estimate that the 9932 updates 3
times per second, and the 506 updates 2 times per second. The integration
times are probably .33 and .5 seconds respectively.

I have measured the receiver equivalent noise bandwidth and it is 1600Hz.

95% of 250 readings were within 0.41dB for the 9932 and 0.31dB for the
506. These observations reconcile well with my Chi-squared based estimate
of the uncertainty that I referred to in an earlier post.

As for the number of digits, they are both 4 digit multimeters which
doesn't mean a lot. They were used to measure 200mV with 1mV resolution,
so the representational error is 0.04dB. The error due to the number of
digits in this downscale three digit application is insignificant
compared to the sampling error of 0.4dB and 0.3dB.

Graphically, the distributions are shown at
http://www.vk1od.net/nfm/temp.gif .

Different meters with different integration times, and different
receivers with different noise bandwidth will result in different
outcomes, but I argue that the uncertainty is predictable.

Owen
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
"Noise" antenna for MFJ-1026 "Noise Canceling Signal Enhancer" Eric Antenna 1 February 24th 07 06:01 PM
Shortwave Listening (SWL) Noise in Urban {Downtown) Location - Anti-Jammimg {Anti-Man-Made-Noise} Shortwave Antenna System RHF Shortwave 0 March 29th 06 05:25 AM
WTB: HP/Agilent 346A (or B) Noise Source for HP 8970A Noise Figure Meter Carl R. Stevenson Homebrew 0 January 21st 04 04:20 AM
Automatic RF noise cancellation and audio noise measurement JGBOYLES Antenna 25 August 11th 03 01:07 AM
Automatic RF noise cancellation and audio noise measurement Dave Shrader Homebrew 35 August 11th 03 01:07 AM


All times are GMT +1. The time now is 05:16 AM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017