LinkBack Thread Tools Search this Thread Display Modes
Prev Previous Post   Next Post Next
  #9   Report Post  
Old May 24th 04, 04:57 AM
Tam/WB2TT
 
Posts: n/a
Default


"Cecil Moore" wrote in message
...
Tam/WB2TT wrote:
It shows the composite voltage waveform, and the net current. Exactly

what a
Bird wattmeter would do.


That's not what a Bird wattmeter does. A Bird wattmeter possesses
a directional coupler.


Sort of. I have built circuits that subtract out the transmitted signal,
leaving the received signal.signal. The Bird is cruder than that.

SPICE apparently does not.


I was driving it with a sine wave, but did a transient analysis. The whole
point is it does not have to know about reflections. It calculates the
waveform by using the same rules that are used to derive standing waves and
reflections.

Is it possible
to add a directional coupler to SPICE?


I have built a SPICE model of a Kenwood power/SWR meter (Have better
schematic than for a Bird). Actually, an idealized version that is not
physically realizable; I did this on purpose. Clearly shows what the
limitations are. Interesting thing is that there is information present that
no SWR meter that I know of displays. For an SWR other than 1:1, you can
deduce whether RL is bigger or smaller than Z0 by comparing two voltages.


If you know the Z0, the net
voltage/current magnitudes/phases, it should be possible to use
phasor addition/subtraction to obtain the forward and reflected
components, just like the Bird wattmeter does.


But there is only one voltage sample, which is the sum of Vf and Vr. There
*are* two current samples, but they are exactly the same, only one is 180
degrees out of phase due to looking at the opposite end of the current
transformer.

Here is what happens. Say you want a meter that shows 100W full scale when
feeding a 50 Ohm load. That is 70.7 V and 1.414 A. In the "Forward"
direction this leads to

100 = 70.7K1 + 1.414K2

In the "Reverse"direction, we know that Pr=0, so

0 = 70.7K1 - 1.414K2 ( The minus sign comes from reversing the current
reading).

You have 2 equations, so you can solve for K1 and K2. You know it can't
*really* measure power, because there is no multiplier. Just like the Bird,
it *adds* (vector wise) voltage and current.
--
73, Cecil http://www.qsl.net/w5dxp



-----= Posted via Newsfeeds.Com, Uncensored Usenet News =-----
http://www.newsfeeds.com - The #1 Newsgroup Service in the World!
-----== Over 100,000 Newsgroups - 19 Different Servers! =-----



 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Rho = (Zload-Zo*)/(Zload+Zo), for complex Zo Dr. Slick Antenna 198 September 24th 03 06:19 PM
Derivation of the Reflection Coefficient? Dr. Slick Antenna 104 September 6th 03 02:27 AM
Length of Coax Affecting Incident Power to Meter? Dr. Slick Antenna 140 August 18th 03 08:17 PM


All times are GMT +1. The time now is 01:49 AM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017