Home |
Search |
Today's Posts |
|
#1
|
|||
|
|||
Omni
On 3/8/2012 11:09 AM, dave wrote:
On Thu, 08 Mar 2012 08:51:20 -0600, NM5K wrote: Also, ground mounted verticals will still need radials if the antenna is to live up to it's expectations. And there is nothing to stop one from using one elevated, if one uses resonant radials for each band to be used. My GAP Titan DX requires no radials; it is a center fed, asymmetric vertical dipole. Well, ground mounted monopoles in his case.. Being a "complete" antenna, it's true that the center fed vertical does not require radials for proper operation, but you would still likely show lower ground losses if it were over radials. For instance, broadcast stations that use 1/2 wave radiators still use a set of radials under the antenna. Usually 1/2 wave radials, when used with a 1/2 wave radiator. You will still see some ground loss with the ground mounted 1/2 waves over poor ground, but being as the max current point is 1/4 up from the ground, it's not near as severe as the ground mounted 1/4 wave where maximum current is at the base. |
#2
|
|||
|
|||
Omni
Thanks for the ideas
When I find it I will post it. 73s "NM5K" wrote in message ... On 3/8/2012 11:09 AM, dave wrote: On Thu, 08 Mar 2012 08:51:20 -0600, NM5K wrote: Also, ground mounted verticals will still need radials if the antenna is to live up to it's expectations. And there is nothing to stop one from using one elevated, if one uses resonant radials for each band to be used. My GAP Titan DX requires no radials; it is a center fed, asymmetric vertical dipole. Well, ground mounted monopoles in his case.. Being a "complete" antenna, it's true that the center fed vertical does not require radials for proper operation, but you would still likely show lower ground losses if it were over radials. For instance, broadcast stations that use 1/2 wave radiators still use a set of radials under the antenna. Usually 1/2 wave radials, when used with a 1/2 wave radiator. You will still see some ground loss with the ground mounted 1/2 waves over poor ground, but being as the max current point is 1/4 up from the ground, it's not near as severe as the ground mounted 1/4 wave where maximum current is at the base. |
#3
|
|||
|
|||
Omni
On Thu, 08 Mar 2012 12:35:58 -0600, NM5K wrote:
On 3/8/2012 11:09 AM, dave wrote: On Thu, 08 Mar 2012 08:51:20 -0600, NM5K wrote: Also, ground mounted verticals will still need radials if the antenna is to live up to it's expectations. And there is nothing to stop one from using one elevated, if one uses resonant radials for each band to be used. My GAP Titan DX requires no radials; it is a center fed, asymmetric vertical dipole. Well, ground mounted monopoles in his case.. Being a "complete" antenna, it's true that the center fed vertical does not require radials for proper operation, but you would still likely show lower ground losses if it were over radials. For instance, broadcast stations that use 1/2 wave radiators still use a set of radials under the antenna. Usually 1/2 wave radials, when used with a 1/2 wave radiator. You will still see some ground loss with the ground mounted 1/2 waves over poor ground, but being as the max current point is 1/4 up from the ground, it's not near as severe as the ground mounted 1/4 wave where maximum current is at the base. I don't think a ground screen is needed if you are 1/2 wave. If you elevate a short vertical you only need a few "ground" radials (think CB groundplane antenna), btw. My whole transmit antenna system floats on my roof. The only "ground" is the panel where the RF goes through the wall. I receive on a balanced 30m horizontal loop, also floating except for the point of entry. I have an automatic tuner at the feedpoint under the eave by my kitchen window. (FWIW) I have lived here 14 years and have never seen lightning at the shack. |
#4
|
|||
|
|||
Omni
On Fri, 09 Mar 2012 09:58:45 -0600, dave wrote:
On Thu, 08 Mar 2012 12:35:58 -0600, NM5K wrote: On 3/8/2012 11:09 AM, dave wrote: On Thu, 08 Mar 2012 08:51:20 -0600, NM5K wrote: Also, ground mounted verticals will still need radials if the antenna is to live up to it's expectations. And there is nothing to stop one from using one elevated, if one uses resonant radials for each band to be used. My GAP Titan DX requires no radials; it is a center fed, asymmetric vertical dipole. Well, ground mounted monopoles in his case.. Being a "complete" antenna, it's true that the center fed vertical does not require radials for proper operation, but you would still likely show lower ground losses if it were over radials. For instance, broadcast stations that use 1/2 wave radiators still use a set of radials under the antenna. Usually 1/2 wave radials, when used with a 1/2 wave radiator. You will still see some ground loss with the ground mounted 1/2 waves over poor ground, but being as the max current point is 1/4 up from the ground, it's not near as severe as the ground mounted 1/4 wave where maximum current is at the base. I don't think a ground screen is needed if you are 1/2 wave. If you elevate a short vertical you only need a few "ground" radials (think CB groundplane antenna), btw. My whole transmit antenna system floats on my roof. The only "ground" is the panel where the RF goes through the wall. I receive on a balanced 30m horizontal loop, also floating except for the point of entry. I have an automatic tuner at the feedpoint under the eave by my kitchen window. (FWIW) I have lived here 14 years and have never seen lightning at the shack. WABC on the rocks http://www.musicradio77.com/transm.html |
#5
|
|||
|
|||
Omni
On Fri, 09 Mar 2012 10:00:10 -0600, dave wrote:
On Fri, 09 Mar 2012 09:58:45 -0600, dave wrote: On Thu, 08 Mar 2012 12:35:58 -0600, NM5K wrote: On 3/8/2012 11:09 AM, dave wrote: On Thu, 08 Mar 2012 08:51:20 -0600, NM5K wrote: Also, ground mounted verticals will still need radials if the antenna is to live up to it's expectations. And there is nothing to stop one from using one elevated, if one uses resonant radials for each band to be used. My GAP Titan DX requires no radials; it is a center fed, asymmetric vertical dipole. Well, ground mounted monopoles in his case.. Being a "complete" antenna, it's true that the center fed vertical does not require radials for proper operation, but you would still likely show lower ground losses if it were over radials. For instance, broadcast stations that use 1/2 wave radiators still use a set of radials under the antenna. Usually 1/2 wave radials, when used with a 1/2 wave radiator. You will still see some ground loss with the ground mounted 1/2 waves over poor ground, but being as the max current point is 1/4 up from the ground, it's not near as severe as the ground mounted 1/4 wave where maximum current is at the base. I don't think a ground screen is needed if you are 1/2 wave. If you elevate a short vertical you only need a few "ground" radials (think CB groundplane antenna), btw. My whole transmit antenna system floats on my roof. The only "ground" is the panel where the RF goes through the wall. I receive on a balanced 30m horizontal loop, also floating except for the point of entry. I have an automatic tuner at the feedpoint under the eave by my kitchen window. (FWIW) I have lived here 14 years and have never seen lightning at the shack. WABC on the rocks http://www.musicradio77.com/transm.html Bird's Eye View: http://www.bing.com/maps/default.aspx? v=2&cp=40.880654933621~-74.069307757843&style=a&lvl=15&sp=Point.40.8806549 33621_ |
#6
|
|||
|
|||
Omni
On 3/9/2012 10:13 AM, dave wrote:
WABC on the rocks http://www.musicradio77.com/transm.html I bet their halfwave is sitting on a bed of 1/2 WL radials. Most 1/2 wave BC antennas tend to use 1/2 wave radials I'm fairly sure. Part of this is due to FCC requirements for stability in performance, etc.. A 1/2 WL radiator on the ground is not immune to ground losses. It just suffers less than the 1/4 WL. And a 1/2 wave elevated, really should be decoupled from the feed line for best performance. Of course, it's not required, but they will perform better if you use decoupling. Less skewing of the pattern off the horizon, from feed line currents. |
#7
|
|||
|
|||
Omni
On 3/9/2012 9:58 AM, dave wrote:
I don't think a ground screen is needed if you are 1/2 wave. It's not required to provide the lower half of the antenna, but they will still reduce ground losses if the antenna is ground mounted. If you elevate a short vertical you only need a few "ground" radials (think CB groundplane antenna), btw. My whole transmit antenna system floats on my roof. The only "ground" is the panel where the RF goes through the wall. I receive on a balanced 30m horizontal loop, also floating except for the point of entry. I have an automatic tuner at the feedpoint under the eave by my kitchen window. (FWIW) I have lived here 14 years and have never seen lightning at the shack. The number of elevated radials needed to equal certain number on the ground will depend on the wavelength above ground. IE: to equal 120 1/4 WL radials on the ground, at 1/8 WL, you will need appx 60 of them. At 1/4 WL, appx 8-10.. At 1/2 WL, 3-4.. And if the radiator is short, the radial system is a bit more critical than with a full size 1/4 wave radiator. |
#8
|
|||
|
|||
Omni
Found it
Actually, I found some very old schematics , the paper is yellowish tea like. Japanese I think . Hidaka. http://www.hidaka.com/e-a_multi-v.html#VS-41W I am pretty sure the one I have now is the VS-80KR. I am going to clean it up and try it out. Don't know what will happen when I put it on a 50 ft tower in these windy days. Will have to calculate the length of gnd planes. I suspect they will be too long. Any recommendations? Thanks 73 "NM5K" wrote in message ... On 3/9/2012 9:58 AM, dave wrote: I don't think a ground screen is needed if you are 1/2 wave. It's not required to provide the lower half of the antenna, but they will still reduce ground losses if the antenna is ground mounted. If you elevate a short vertical you only need a few "ground" radials (think CB groundplane antenna), btw. My whole transmit antenna system floats on my roof. The only "ground" is the panel where the RF goes through the wall. I receive on a balanced 30m horizontal loop, also floating except for the point of entry. I have an automatic tuner at the feedpoint under the eave by my kitchen window. (FWIW) I have lived here 14 years and have never seen lightning at the shack. The number of elevated radials needed to equal certain number on the ground will depend on the wavelength above ground. IE: to equal 120 1/4 WL radials on the ground, at 1/8 WL, you will need appx 60 of them. At 1/4 WL, appx 8-10.. At 1/2 WL, 3-4.. And if the radiator is short, the radial system is a bit more critical than with a full size 1/4 wave radiator. |
#9
|
|||
|
|||
Omni
On 3/9/2012 3:09 PM, Tuuk wrote:
Found it Actually, I found some very old schematics , the paper is yellowish tea like. Japanese I think . Hidaka. http://www.hidaka.com/e-a_multi-v.html#VS-41W I am pretty sure the one I have now is the VS-80KR. I am going to clean it up and try it out. Don't know what will happen when I put it on a 50 ft tower in these windy days. Will have to calculate the length of gnd planes. I suspect they will be too long. Any recommendations? Not really, as the antenna in the picture seems to use loaded/trapped radials. So you will need their assembly specs if you have those and plan to use them. Or maybe assemble them and try to tune them. If elevated, any full size wire radials will need to be resonant. If ground mounted, there is no need to tune radials laying on or in the ground. |
#10
|
|||
|
|||
Omni
I don't have the ground planes for this antenna, just the vertical main
mast. Used on the ground would be difficult because I am sandwiched between houses all around me. I wonder would the mismatch be so significant that the efficientcy of the antenna be almost completely lost? If used with a good tuner would the radiation resistence of the antenna become totally innefficient if I were to completely ground it out through the tower? Nice idea having a omni all hf band antenna. I run barefoot anyway. I think I will try it out anyway, I have one of those MFJ old manual tuners and am sure it would match the feedline coax with the antenna to the load. Just curious how efficient the antenna would radiate. Being 50 foot above the ground, approx 500 ft above sea level anyway. I think the deciding factor is that there is nothing on top of the tower now anyway. Thanks 73 "NM5K" wrote in message ... On 3/9/2012 3:09 PM, Tuuk wrote: Found it Actually, I found some very old schematics , the paper is yellowish tea like. Japanese I think . Hidaka. http://www.hidaka.com/e-a_multi-v.html#VS-41W I am pretty sure the one I have now is the VS-80KR. I am going to clean it up and try it out. Don't know what will happen when I put it on a 50 ft tower in these windy days. Will have to calculate the length of gnd planes. I suspect they will be too long. Any recommendations? Not really, as the antenna in the picture seems to use loaded/trapped radials. So you will need their assembly specs if you have those and plan to use them. Or maybe assemble them and try to tune them. If elevated, any full size wire radials will need to be resonant. If ground mounted, there is no need to tune radials laying on or in the ground. |
Reply |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Ten Tec Omni D and ext VFO | Boatanchors | |||
FA: Ten-Tec Omni VI Plus "LAST DAY" | Swap | |||
FA: Ten-Tec Omni VI Plus | Swap | |||
WTB: Ten-Tec OMNI VI+ | Swap | |||
WTB TEN-TEC Omni V or VI | Swap |