On 7/5/2015 4:45 PM, Jerry Stuckle wrote:
On 7/5/2015 3:58 PM, Roger Hayter wrote:
Jerry Stuckle wrote:

On 7/5/2015 9:23 AM, Ian Jackson wrote:
In message ,
writes
Wayne wrote:


"Jeff Liebermann" wrote in message
...

On Sat, 04 Jul 2015 19:04:01 -0400, Jerry Stuckle
wrote:
Think of it this way, without the math. On the transmitter side of
the
network, the match is 1:1, with nothing reflected back to the
transmitter.

So you have a signal coming back from the antenna. You have a perfect
matching network, which means nothing is lost in the network. The
feedline is perfect, so there is no loss in it. The only place for
the
signal to go is back to the antenna.

Wikipedia says that if the source is matched to the line, any
reflections that come back are absorbed, not reflected back to the
antenna:

https://en.wikipedia.org/wiki/Impedance_matching
"If the source impedance matches the line, reflections
from the load end will be absorbed at the source end.
If the transmission line is not matched at both ends
reflections from the load will be re-reflected at the
source and re-re-reflected at the load end ad infinitum,
losing energy on each transit of the transmission line."

Well, I looked at that section of the writeup.
And, I have no idea what the hell they are talking about.
Looks like a good section for a knowledgeable person to edit.

If the termination matches the line impedance, there is no reflection.

Both the antenna and the source are terminations.

This is a bit difficult to visualze with an RF transmitter, but is
more easily seen with pulses.

Being essentially a simple soul, that's how I sometimes try to work out
what happening.

You'll be better off if you killfile the troll. You'll get a lot less
bad information and your life will become much easier.


The wikipedia entry is correct as written.

In the real world, the output of an amateur transmitter will seldom
be exactly 50 Ohms unless there is an adjustable network of some
sort.

I've always understood that the resistive part of a TX output impedance
was usually less than 50 ohms.

If a transmitter output impedance WAS 50 ohms, I would have thought that
the efficiency of the output stage could never exceed 50% (and aren't
class-C PAs supposed to be around 66.%?). Also, as much power would be
dissipated in the PA stage as in the load.

Fixed output amateur transmitters are a nominal 50 ohms. It can vary,
but that is due to normal variances in components, and the difference
can be ignored in real life.

But output impedance has little to do with efficiency. A Class C
amplifier can run 90%+ efficiency. It's output may be anything, i.e.
high with tubes but low with solid state. But the output impedance can
be converted to 50 ohms or any other reasonable impedance through a
matching network.

A perfect matching network will have no loss, so everything the
transmitter puts out will go through the matching network. Of course,
nothing is perfect, so there will be some loss. But the amount of loss
in a 1:1 match will not be significant.

Also, the amplifier generates the power; in a perfect world, 100% of
that power is transferred to the load. The transmitter doesn't
dissipate 1/2 of the power and the load the other 1/2. It's not like
having two resistors in a circuit where each will dissipate 1/2 of the
power.

BTW - the resistive part of the impedance is not the same as resistance.
For a simple case - take a series circuit of a capacitor, an inductor
and a 50 ohm resistor. At the resonant frequency, the impedance will
be 50 +j0 (50 ohms from the resistor, capacitive and inductive
reactances cancel). But the DC resistance is infinity. Again, a simple
example, but it shows a point.

The resistive part of the impedance is exactly the same as a resistance
as far as the frequency you are using is concerned. And if the
amplifier output impedance *and* the feeder input resistance were *both*
matched to 50 ohms resistive then 50% of the power generated (after
circuit losses due of inefficiency of generation) would be dissipated in
the transmitter. It would, at the working frequency, be *exactly* like
having two equal resistors in the circuit each taking half the generated
power. So the amplifier has a much lower output impedance than 50ohms
and no attempt is made to match it to 50 ohms.


OK, so then please explain how I can have a Class C amplifier with 1KW
DC input and a 50 ohm output, 50 ohm coax and a matching network at the
antenna can show 900 watt (actually about 870 watts due to feedline
loss)? According to your statement, that is impossible. I should not
be able get more than 450W or so at the antenna.

It is true that if the transmitter is thought of as a fixed voltage
generator in series with, say, a 5 ohm resistor then the maximum power
transfer in theory would occur with a 5 ohm load. But to achieve this
the output power would have to be 100 times higher (ten times the
voltage) and half of it would be dissipated in the PA. Not the best way
to run things, it is better to have a voltage generator chosen to give
the right power with the load being much bigger than its generator
resistance.


So why do all fixed-tuning amateur transmitters have a nominal 50 ohm
output instead of 1 or two ohms? And why do commercial radio stations
spend tens of thousands of dollars ensuring impedance is matched
throughout the system?

The maximum power transfer at equal impedance theorem only applies if
you started with a *fixed* output voltage generator. We don't; we
start with a load impedance (50 ohm resistive), then we decide what
power output we want, and we choose the voltage to be generated
accordingly. (Thank you for giving me the opportunity to think about
this!)


Actually, it doesn't matter if it's a fixed or a variable output voltage
- maximum power transfer always occurs when there is an impedance match.

How about we quit with the speculation and come up with some numbers?

Here is a simulation of a 50 ohm load with a 50 ohm matched series
output impedance and a voltage source of 200 VAC peak. Power into the
load is 100 W.

http://arius.com/sims/Matched%20Load%20Power.png

Same exact circuit with the series impedance of just 1 ohm, power into
the load is 385 W.

http://arius.com/sims/UnMatched%20Load%20Power.png

I'd say that is pretty clear evidence that matched loads are not the way
to maximize power transfer when the load impedance is fixed and the
output impedance is controllable.

--

Rick

On 7/6/2015 12:39 AM, rickman wrote:
On 7/5/2015 4:45 PM, Jerry Stuckle wrote:

Actually, it doesn't matter if it's a fixed or a variable output voltage
- maximum power transfer always occurs when there is an impedance match.

How about we quit with the speculation and come up with some numbers?

Here is a simulation of a 50 ohm load with a 50 ohm matched series
output impedance and a voltage source of 200 VAC peak. Power into the
load is 100 W.

http://arius.com/sims/Matched%20Load%20Power.png

Same exact circuit with the series impedance of just 1 ohm, power into
the load is 385 W.

http://arius.com/sims/UnMatched%20Load%20Power.png

I'd say that is pretty clear evidence that matched loads are not the way
to maximize power transfer when the load impedance is fixed and the
output impedance is controllable.

In case anyone wants to duplicate the simulation...

Version 4
SHEET 1 880 680
WIRE 48 48 0 48
WIRE 144 48 48 48
WIRE 304 48 224 48
WIRE 336 48 304 48
WIRE 0 80 0 48
WIRE 336 80 336 48
WIRE 0 192 0 160
WIRE 336 192 336 160
WIRE 48 304 0 304
WIRE 144 304 48 304
WIRE 304 304 224 304
WIRE 336 304 304 304
WIRE 0 336 0 304
WIRE 336 336 336 304
WIRE 0 448 0 416
WIRE 336 448 336 416
FLAG 0 192 0
FLAG 336 192 0
FLAG 48 48 V1
FLAG 304 48 Vload1
FLAG 0 448 0
FLAG 336 448 0
FLAG 48 304 V2
FLAG 304 304 Vload2
SYMBOL voltage 0 64 R0
WINDOW 123 0 0 Left 2
WINDOW 39 0 0 Left 2
SYMATTR InstName V1
SYMATTR Value SINE(0 200 100K)
SYMBOL res 320 64 R0
SYMATTR InstName RL1
SYMATTR Value 50
SYMBOL res 128 64 R270
WINDOW 0 32 56 VTop 2
WINDOW 3 0 56 VBottom 2
SYMATTR InstName RS1
SYMATTR Value 50
SYMBOL voltage 0 320 R0
WINDOW 123 0 0 Left 2
WINDOW 39 0 0 Left 2
SYMATTR InstName V2
SYMATTR Value SINE(0 200 100K)
SYMBOL res 320 320 R0
SYMATTR InstName RL2
SYMATTR Value 50
SYMBOL res 128 320 R270
WINDOW 0 32 56 VTop 2
WINDOW 3 0 56 VBottom 2
SYMATTR InstName RS2
SYMATTR Value 1
TEXT -34 472 Left 2 !.tran 10us


--

Rick

In message , rickman
writes



How about we quit with the speculation and come up with some numbers?

Here is a simulation of a 50 ohm load with a 50 ohm matched series
output impedance and a voltage source of 200 VAC peak. Power into the
load is 100 W.

http://arius.com/sims/Matched%20Load%20Power.png

Same exact circuit with the series impedance of just 1 ohm, power into
the load is 385 W.

http://arius.com/sims/UnMatched%20Load%20Power.png

I'd say that is pretty clear evidence that matched loads are not the
way to maximize power transfer when the load impedance is fixed and the
output impedance is controllable.

Quite simply, if your prime objective is to get maximum power out of a
power (energy?) source, the source having an internal resistance is a
BAD THING. You don't design the source to have an internal resistance
equal to its intended load resistance. No one designs lead-acid
batteries that way (do they?), so why RF transmitters?

While theoretically you can extract the maximum power available from the
source when the load resistance equals the source resistance, you can
only do so provided that the heat you generate in the source does not
cause the source to malfunction (in the worst case, blow up).
--
Ian

On 7/6/2015 4:20 AM, Ian Jackson wrote:
In message , rickman writes



How about we quit with the speculation and come up with some numbers?

Here is a simulation of a 50 ohm load with a 50 ohm matched series
output impedance and a voltage source of 200 VAC peak. Power into the
load is 100 W.

http://arius.com/sims/Matched%20Load%20Power.png

Same exact circuit with the series impedance of just 1 ohm, power into
the load is 385 W.

http://arius.com/sims/UnMatched%20Load%20Power.png

I'd say that is pretty clear evidence that matched loads are not the
way to maximize power transfer when the load impedance is fixed and
the output impedance is controllable.

Quite simply, if your prime objective is to get maximum power out of a
power (energy?) source, the source having an internal resistance is a
BAD THING. You don't design the source to have an internal resistance
equal to its intended load resistance. No one designs lead-acid
batteries that way (do they?), so why RF transmitters?

While theoretically you can extract the maximum power available from the
source when the load resistance equals the source resistance, you can
only do so provided that the heat you generate in the source does not
cause the source to malfunction (in the worst case, blow up).

Because DC power transfer is not the same as AC power transfer.

If what you say is correct, then it wouldn't matter what antenna
impedance I had, as long as it matches the transmission line. VSWR
would be immaterial.

That is demonstrably false.

--
==================
Remove the "x" from my email address
Jerry, AI0K

==================

On 7/6/2015 11:01 AM, Jerry Stuckle wrote:
On 7/6/2015 4:20 AM, Ian Jackson wrote:
In message , rickman writes



How about we quit with the speculation and come up with some numbers?

Here is a simulation of a 50 ohm load with a 50 ohm matched series
output impedance and a voltage source of 200 VAC peak. Power into the
load is 100 W.

http://arius.com/sims/Matched%20Load%20Power.png

Same exact circuit with the series impedance of just 1 ohm, power into
the load is 385 W.

http://arius.com/sims/UnMatched%20Load%20Power.png

I'd say that is pretty clear evidence that matched loads are not the
way to maximize power transfer when the load impedance is fixed and
the output impedance is controllable.

Quite simply, if your prime objective is to get maximum power out of a
power (energy?) source, the source having an internal resistance is a
BAD THING. You don't design the source to have an internal resistance
equal to its intended load resistance. No one designs lead-acid
batteries that way (do they?), so why RF transmitters?

While theoretically you can extract the maximum power available from the
source when the load resistance equals the source resistance, you can
only do so provided that the heat you generate in the source does not
cause the source to malfunction (in the worst case, blow up).

Because DC power transfer is not the same as AC power transfer.


Why not? Does something happen to the laws of physics with AC?


If what you say is correct, then it wouldn't matter what antenna
impedance I had, as long as it matches the transmission line. VSWR
would be immaterial.


There is no VSWR nor ISWR if the load matches the line.


That is demonstrably false.

Please demonstrate this for us as we wish to learn.

John S wrote:
On 7/6/2015 11:01 AM, Jerry Stuckle wrote:
On 7/6/2015 4:20 AM, Ian Jackson wrote:
In message , rickman writes



How about we quit with the speculation and come up with some numbers?

Here is a simulation of a 50 ohm load with a 50 ohm matched series
output impedance and a voltage source of 200 VAC peak. Power into the
load is 100 W.

http://arius.com/sims/Matched%20Load%20Power.png

Same exact circuit with the series impedance of just 1 ohm, power into
the load is 385 W.

http://arius.com/sims/UnMatched%20Load%20Power.png

I'd say that is pretty clear evidence that matched loads are not the
way to maximize power transfer when the load impedance is fixed and
the output impedance is controllable.

Quite simply, if your prime objective is to get maximum power out of a
power (energy?) source, the source having an internal resistance is a
BAD THING. You don't design the source to have an internal resistance
equal to its intended load resistance. No one designs lead-acid
batteries that way (do they?), so why RF transmitters?

While theoretically you can extract the maximum power available from the
source when the load resistance equals the source resistance, you can
only do so provided that the heat you generate in the source does not
cause the source to malfunction (in the worst case, blow up).

Because DC power transfer is not the same as AC power transfer.


Why not? Does something happen to the laws of physics with AC?

Yes, quite a lot, you get a whole new set of laws.

Capacitors are an open circuit at DC and have a frequency dependant
impedance at AC.

Inductors are a short circuit at DC and have a frequency dependant
impedance at AC.

There is no such thing as a transmission line at DC.

Current at DC is constant and does not cause propagation while current
at AC causes a varying electromagnetic field that can propagate.

There is no such thing as a phase angle at DC.

A wire carrying DC current will not induce a voltage into another nearby
wire but a wire carrying AC current will.

More?


--
Jim Pennino

On 7/6/2015 1:03 PM, wrote:
John S wrote:
On 7/6/2015 11:01 AM, Jerry Stuckle wrote:
On 7/6/2015 4:20 AM, Ian Jackson wrote:
In message , rickman writes



How about we quit with the speculation and come up with some numbers?

Here is a simulation of a 50 ohm load with a 50 ohm matched series
output impedance and a voltage source of 200 VAC peak. Power into the
load is 100 W.

http://arius.com/sims/Matched%20Load%20Power.png

Same exact circuit with the series impedance of just 1 ohm, power into
the load is 385 W.

http://arius.com/sims/UnMatched%20Load%20Power.png

I'd say that is pretty clear evidence that matched loads are not the
way to maximize power transfer when the load impedance is fixed and
the output impedance is controllable.

Quite simply, if your prime objective is to get maximum power out of a
power (energy?) source, the source having an internal resistance is a
BAD THING. You don't design the source to have an internal resistance
equal to its intended load resistance. No one designs lead-acid
batteries that way (do they?), so why RF transmitters?

While theoretically you can extract the maximum power available from the
source when the load resistance equals the source resistance, you can
only do so provided that the heat you generate in the source does not
cause the source to malfunction (in the worst case, blow up).

Because DC power transfer is not the same as AC power transfer.


Why not? Does something happen to the laws of physics with AC?

Yes, quite a lot, you get a whole new set of laws.

If you apply 1vDC to a 1 ohm resistor, you get 1A of current. If you
apply 1vAC RMS (at any frequency) to a 1 ohm resistor, you get 1A of
current. How does the AC change the law?

On 7/7/2015 3:05 AM, John S wrote:
On 7/6/2015 1:03 PM, wrote:
John S wrote:
On 7/6/2015 11:01 AM, Jerry Stuckle wrote:
On 7/6/2015 4:20 AM, Ian Jackson wrote:
In message , rickman
writes



How about we quit with the speculation and come up with some numbers?

Here is a simulation of a 50 ohm load with a 50 ohm matched series
output impedance and a voltage source of 200 VAC peak. Power into
the
load is 100 W.

http://arius.com/sims/Matched%20Load%20Power.png

Same exact circuit with the series impedance of just 1 ohm, power
into
the load is 385 W.

http://arius.com/sims/UnMatched%20Load%20Power.png

I'd say that is pretty clear evidence that matched loads are not the
way to maximize power transfer when the load impedance is fixed and
the output impedance is controllable.

Quite simply, if your prime objective is to get maximum power out of a
power (energy?) source, the source having an internal resistance is a
BAD THING. You don't design the source to have an internal resistance
equal to its intended load resistance. No one designs lead-acid
batteries that way (do they?), so why RF transmitters?

While theoretically you can extract the maximum power available
from the
source when the load resistance equals the source resistance, you can
only do so provided that the heat you generate in the source does not
cause the source to malfunction (in the worst case, blow up).

Because DC power transfer is not the same as AC power transfer.


Why not? Does something happen to the laws of physics with AC?

Yes, quite a lot, you get a whole new set of laws.

If you apply 1vDC to a 1 ohm resistor, you get 1A of current. If you
apply 1vAC RMS (at any frequency) to a 1 ohm resistor, you get 1A of
current. How does the AC change the law?


You apply 1vdc to a 0.159 microfarad capacitor and you get 0 amps
flowing (open circuit).
You apply 1vac at 1MHz to that same capacitor and you get 1 amp flowing,
with the current leading the voltage by 90 degrees.

You apply 1vdc to a 0.159 microhenry inductor and you get infinite amps
flowing (short circuit).
You apply 1vdc at 1MHz to that same inductor, and you get 1 amp flowing
with the voltage leading the current by 90 degrees.

You place the capacitor and inductor in series.
Fed with DC, you get 0 amps flowing (open circuit).
Fed with 1MHz AC, you get infinite current flowing (short circuit).

You place the capacitor and inductor in parallel.
Fed with DC, you get infinite current flowing (short circuit).
Fed with 1MHz AC you get 0 amps flowing (open circuit).

There is a huge difference between ac and dc!

--
==================
Remove the "x" from my email address
Jerry, AI0K

==================

John S wrote:
On 7/6/2015 1:03 PM, wrote:
John S wrote:
On 7/6/2015 11:01 AM, Jerry Stuckle wrote:
On 7/6/2015 4:20 AM, Ian Jackson wrote:
In message , rickman writes



How about we quit with the speculation and come up with some numbers?

Here is a simulation of a 50 ohm load with a 50 ohm matched series
output impedance and a voltage source of 200 VAC peak. Power into the
load is 100 W.

http://arius.com/sims/Matched%20Load%20Power.png

Same exact circuit with the series impedance of just 1 ohm, power into
the load is 385 W.

http://arius.com/sims/UnMatched%20Load%20Power.png

I'd say that is pretty clear evidence that matched loads are not the
way to maximize power transfer when the load impedance is fixed and
the output impedance is controllable.

Quite simply, if your prime objective is to get maximum power out of a
power (energy?) source, the source having an internal resistance is a
BAD THING. You don't design the source to have an internal resistance
equal to its intended load resistance. No one designs lead-acid
batteries that way (do they?), so why RF transmitters?

While theoretically you can extract the maximum power available from the
source when the load resistance equals the source resistance, you can
only do so provided that the heat you generate in the source does not
cause the source to malfunction (in the worst case, blow up).

Because DC power transfer is not the same as AC power transfer.


Why not? Does something happen to the laws of physics with AC?

Yes, quite a lot, you get a whole new set of laws.

If you apply 1vDC to a 1 ohm resistor, you get 1A of current. If you
apply 1vAC RMS (at any frequency) to a 1 ohm resistor, you get 1A of
current. How does the AC change the law?

What part of "you get a whole new set of laws" was it you failed
to understand?

Here's a clue for you; at DC the reactive components of a length
of wire are irrelevant but at AC they are not.


--
Jim Pennino

On 7/6/2015 12:41 PM, John S wrote:
On 7/6/2015 11:01 AM, Jerry Stuckle wrote:
On 7/6/2015 4:20 AM, Ian Jackson wrote:
In message , rickman
writes



How about we quit with the speculation and come up with some numbers?

Here is a simulation of a 50 ohm load with a 50 ohm matched series
output impedance and a voltage source of 200 VAC peak. Power into the
load is 100 W.

http://arius.com/sims/Matched%20Load%20Power.png

Same exact circuit with the series impedance of just 1 ohm, power into
the load is 385 W.

http://arius.com/sims/UnMatched%20Load%20Power.png

I'd say that is pretty clear evidence that matched loads are not the
way to maximize power transfer when the load impedance is fixed and
the output impedance is controllable.

Quite simply, if your prime objective is to get maximum power out of a
power (energy?) source, the source having an internal resistance is a
BAD THING. You don't design the source to have an internal resistance
equal to its intended load resistance. No one designs lead-acid
batteries that way (do they?), so why RF transmitters?

While theoretically you can extract the maximum power available from the
source when the load resistance equals the source resistance, you can
only do so provided that the heat you generate in the source does not
cause the source to malfunction (in the worst case, blow up).

Because DC power transfer is not the same as AC power transfer.


Why not? Does something happen to the laws of physics with AC?


Yup, AC has reactance. DC does not. Big difference.


If what you say is correct, then it wouldn't matter what antenna
impedance I had, as long as it matches the transmission line. VSWR
would be immaterial.


There is no VSWR nor ISWR if the load matches the line.


Sure, there is ALWAYS VSWR. It may be 1:1, but it's always there.


That is demonstrably false.

Please demonstrate this for us as we wish to learn.



OK, take your amateur transmitter. Connect it through a 1:1 balun to
300 ohm feedline. Connect that to a 300 ohm antenna.

According to you, you should get full power output at the antenna. In
reality, you will get a 6:1 SWR and about 49% of the power at the
antenna, minus transmission line loss (assuming, of course, your
transmitter hasn't cut it's power back).

--
==================
Remove the "x" from my email address
Jerry, AI0K

==================