On 7/12/2015 3:03 PM, Jeff Liebermann wrote:
On Sun, 12 Jul 2015 13:17:53 -0400, rickman wrote:

On 7/12/2015 6:25 AM, Jeff Liebermann wrote:
On Sun, 12 Jul 2015 09:58:00 +0100, "Cottaging by the sea ..."
wrote:

going by adverts the k40 must be the best antenna on the market....can I cut
it for 15m ????

The K40 is a CB antenna made for 27 MHz. 15 meters is 21 MHz and is
therefore lower in frequency than what the K40 is tuned. You would
need to lengthen, not "cut" the antenna in order to lower the
frequency.

I don't get it. I've cut this antenna three times and the frequency is
*still* too high.

The more you cut, the higher the antenna operating frequency.

I guess I should have put a smiley at the end of that. When I worked
construction the guys would kid saying, "I've cut this board off three
times and it's still too short!"

--

Rick

"rickman" wrote in message
...
..

I don't get it. I've cut this antenna three times and the frequency is
*still* too high.

The more you cut, the higher the antenna operating frequency.

I guess I should have put a smiley at the end of that. When I worked
construction the guys would kid saying, "I've cut this board off three
times and it's still too short!"


Reminds me of the time I had carpet put in and needed to cut down a door so
it would close. I cut it twice and it was still too long and rubbed the
carpet. Looked at the top and there was almost an inch gap. Good thing it
was just a closet door.

On 7/12/2015 4:41 PM, Ralph Mowery wrote:
"rickman" wrote in message
...
.

I don't get it. I've cut this antenna three times and the frequency is
*still* too high.

The more you cut, the higher the antenna operating frequency.

I guess I should have put a smiley at the end of that. When I worked
construction the guys would kid saying, "I've cut this board off three
times and it's still too short!"


Reminds me of the time I had carpet put in and needed to cut down a door so
it would close. I cut it twice and it was still too long and rubbed the
carpet. Looked at the top and there was almost an inch gap. Good thing it
was just a closet door.

lol, good one

--

Rick

On Sun, 12 Jul 2015 16:15:13 -0400, rickman wrote:

On 7/12/2015 3:03 PM, Jeff Liebermann wrote:

I don't get it. I've cut this antenna three times and the frequency is
*still* too high.

The more you cut, the higher the antenna operating frequency.

I guess I should have put a smiley at the end of that. When I worked
construction the guys would kid saying, "I've cut this board off three
times and it's still too short!"

"Insanity: Doing the same thing over and over again and expecting
different results." (Big Al Einstein).

Ok, you got me. I thought you were serious. I would have thought
that after cutting three times, you would have gotten the clue that
you were going in the wrong direction.


--
Jeff Liebermann
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558

Jeff Liebermann wrote:

On Sun, 12 Jul 2015 16:15:13 -0400, rickman wrote:

On 7/12/2015 3:03 PM, Jeff Liebermann wrote:

I don't get it. I've cut this antenna three times and the frequency is
*still* too high.

The more you cut, the higher the antenna operating frequency.

I guess I should have put a smiley at the end of that. When I worked
construction the guys would kid saying, "I've cut this board off three
times and it's still too short!"

"Insanity: Doing the same thing over and over again and expecting
different results." (Big Al Einstein).

Ok, you got me. I thought you were serious. I would have thought
that after cutting three times, you would have gotten the clue that
you were going in the wrong direction.

Indeed, I think that fact is what makes the joke funny, at least to some
of us.

--
Roger Hayter