About Us

[email protected] · July 22nd 15, 08:14 PM posted to rec.radio.amateur.antenna

John S wrote:
On 7/22/2015 12:07 PM, wrote:
John S wrote:
If Maxwell can have a Demon, then so can I.

There is a 100W RF transmitter attached to an antenna, through an
ammeter, whose terminal impedance is 50+j0 at an arbitrary frequency,
Fo. The transmitter has a drive control, that is, the amount of power
can be adjusted by my Demon.

I have an RF voltmeter also attached to the antenna/transmitter junction.

The goal is to measure the power into the antenna as frequency is varied.

At Fo, my Demon adjusts the drive level to 50V at the antenna terminal.
The power into the antenna is 50W. So far, so good.

As we sweep the frequency, my Demon adjusts the drive control to supply
50V at the terminal. So, let's plot just 3 points:

R X Z Amps Pwr
37.34 -48.86 61.49 0.813 24.68
50.56 0.06 50.56 0.989 49.44
68.44 48.44 83.84 0.596 24.34

My Demon is only watching the antenna's terminal voltage, adjusting the
drive to maintain 50V and has no idea about R and X. I have included R,
X and the resulting calculations (Z, Amps, Pwr) from a simulated antenna
for those who wish to verify that the the resulting calculations are
correct.

While the load current has changed from .8 amps through .99 amps to .6
amps, the voltage has remained constant.

If you the only thing you know is that the terminal voltage set my Demon
has maintained the voltage at 50V and you can read the current, what
conclusion could you draw about the source impedance? Well, since the
voltage has remained unchanged while the current varied, it would appear
that, for all practical purposes, the source impedance is zero because
the dynamic source impedance is dV/dI (0/dI = 0) at the antenna terminals.

I invite comments about this thought experiment.

Thanks folks, and I promise no bickering and name-calling from me.

Yes, the source impendance of a regulated voltage source can be
concidered to be zero over it's linear range, i.e. it does not go
into limiting.

That the voltage is AC and the load is complex is irrelevant.

Can we describe such a demon that works on current as well? My guess is
that you will agree that it can.

It is called a constant current source.

Like constant voltage sources, there are the theoretical ones and the
practical ones you buy as a chip.

If so, can we have a demon that supplies a constant power? My bet is
that you will agree again.

Theoretical circuit analysis does not use constant power sources.

Constant power sources are sometimes used for things like S-parameter
analysis. They will always have a source impedance.

To build one you design a circuit that monitors the output current
and voltage then adjusts the output voltage to equal the desired power
divided by the output current. This of course will have practical limits
and while not trivial to design, not impossible.

Also it is of no use that I can think of.

This all depends on that hypothetical demon, of course. What do you
think? Can the thought experiment be set up differently or better?

What exactly IS the experiment?

--
Jim Pennino

Thread Tools	Search this Thread
Show Printable Version	Search this Thread: Advanced Search
Display Modes
Switch to Linear Mode Switch to Hybrid Mode Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How much can the impedance of coax vary from its characteristic impedance?	[email protected]	Antenna	23	August 21st 07 10:12 PM
impedance	kretko	Antenna	5	June 11th 06 09:08 AM
Tx Source Impedance & Load Reflections	Richard Fry	Antenna	8	May 28th 04 07:29 PM
A: What is impedance (Z)	Steve Nosko	Antenna	121	March 2nd 04 06:25 AM
SWR will change with Source Z if you measure AT the Source	Tarmo Tammaru	Antenna	18	August 30th 03 04:18 AM

Menu

About Us