Now, that's interesting, because it is a variation of the technique
for setting up for cross drilling (except that then the ruler is in
see-saw mode)

"Wooding" wrote in message
...
Airy R.Bean wrote:
Is there a "kink" for setting up a slitting saw to saw through
round bar stock along the axis, so that the slot is exactly
across a diameter? (I presume this to be a similar problem to
setting up accurately for cross-drilling)

This trick assumes you have the slitting saw in a vertical mill, the bar
is horizontal, and the slitting saw teeth are straight (i.e.. not
staggered like a wood saw blade).
Adjust the position of the bar and saw so that, by eye, the blade is
just about touching the fattest part of the bar. Interpose a vertical
6" steel rule between the bar and the saw and move the table to very
gently pinch the rule. Unless you were lucky and set the saw exactly on
the fattest part, the rule will no longer be vertical. Adjust the hight
of the saw until the rule is truly vertical - you will be amazed at how
accurately the blade is then at centre hight.

I have to make up about 14 such plugs.

(Although a nagging voice inside suggests that I should
also consider the "Binding Post" approach together with
spade terminals)

"jtaylor" wrote in message
...
"Airy R.Bean" wrote in message
...
Thanks for your ideas - it's always the way that there's more
though and effort needed to be put in to make the jig than
to make the device in which you're interested!
"jtaylor" wrote in message
...
I had to thread the hole through my block, but you don't need that.
If
you
wanted to get fancy you could make a shouldered sleeve with your
setscrew
holding the stock, drill a hole in the shoulder, and two holes in the
block
for a pin to set your 90 degree cuts.

If you're making more than half a dozen it'd be worth it.

Damn! I knew I should have purchased that digital
height gauge at the club sale, especially as it was only
£10!

The only difficulty otherwise with what you suggest is
the tendency of slitting saws to bend under the slightest
lateral force, but thanks anyway.

"Andrew Mawson" wrote in message
...
"Airy R.Bean" wrote in message
...
Is there a "kink" for setting up a slitting saw to saw through
round bar stock along the axis, so that the slot is exactly
across a diameter? (I presume this to be a similar problem to
setting up accurately for cross-drilling)
This is actually a Ham Radio application; I wish to make
up some very large banana-type plugs from the 1/4" round
bar stock that I have in small quantities. For this, I will need
to saw two diameters in a cross shape, and then splay
out the leaves slightly to make a springy and rubbing contact.
Assuming you are using a vertical mill so that the slitting saw is
horizontal, and the work is fixtured horizontal (vee block perhaps):
a/ Measure height of top of stock with vernier height guage, subtract
half the stock thickness, and add half the slitting saw thickness -
set the height guage to the resultant figure.
b/ Adjust quill of mill so top of slitting saw just touches the height
guage and lock the quill.
You now have the slitting saw bang on centre of the work.

"Airy R.Bean" wrote in message
...
Is there a "kink" for setting up a slitting saw to saw through
round bar stock along the axis, so that the slot is exactly
across a diameter? (I presume this to be a similar problem to
setting up accurately for cross-drilling)

The simplest way I know to locate a line on top of round stock is this:
(BTW, you don't have to switch from vertical to horizontal modes to make it
work.)

Mount the stock parallel to the mill table, and dead-level, with the
"working end" solidly in your mill vise, and enough overhang for the
slitting saw to clear the vise when you're working on the _side_ of the rod.

True up the work with your longitudinal travel, so it's _pretty_ good. A
thou. is OK, you don't need it to tenths.

With any-ol' side-cutting bit, slowly close in on the side of the work until
the bit just kisses the metal. Then make a longitudinal cut for however far
you want the slit to go.

You've now marked a line and flat that is parallel to the axis of the rod,
and perfectly centered on the horizontal diameter of the rod.

Without removing the work from the vise, you can switch to your slitting
saw, and true up the saw to the line you've just marked -- then cut.

LLoyd

"Airy R.Bean" wrote in message
...
Is there a "kink" for setting up a slitting saw to saw through
round bar stock along the axis, so that the slot is exactly
across a diameter? (I presume this to be a similar problem to
setting up accurately for cross-drilling)

This is actually a Ham Radio application; I wish to make
up some very large banana-type plugs from the 1/4" round
bar stock that I have in small quantities. For this, I will need
to saw two diameters in a cross shape, and then splay
out the leaves slightly to make a springy and rubbing contact.


Doesn't need to be "exactly" because it's the diameter that is more critical
than the position of the slot - I suspect even as much as just less than the
thickness of the slitting saw off centre would not be a problem.

I made a connector (female as opposed to your male) for an old radio by
slitting brass tube. Hacksaw and vice produced good enough accuracy for an
excellent operational performance.

Steve

I made a connector (female as opposed to your male) for an old radio by
slitting brass tube. Hacksaw and vice produced good enough accuracy for an
excellent operational performance.

How about making a square fixture to hold the round part with two slits
to guide the saw blade?

I have found that a good fret/jewelers saw very handy for cutting small
items. I find it very difficult to cut 1/8 drill rod with a hacksaw
but easy with a fret saw. They cut faster than you expect.

Lay the round bar stock in a Vee and put it under the saw so the saw just
touches the highest part of the rod. As long as the stock is round you'll
have a tangent to the diameter and all you need to do is start slotting,
half in two.
There used to be lots of banana plugs for sale on eBay and hamfest, quicker,
easier, and cheaper than DIY.

--

73
Hank WD5JFR
"Airy R.Bean" wrote in message
...
Is there a "kink" for setting up a slitting saw to saw through
round bar stock along the axis, so that the slot is exactly
across a diameter? (I presume this to be a similar problem to
setting up accurately for cross-drilling)

This is actually a Ham Radio application; I wish to make
up some very large banana-type plugs from the 1/4" round
bar stock that I have in small quantities. For this, I will need
to saw two diameters in a cross shape, and then splay
out the leaves slightly to make a springy and rubbing contact.

Set it on center, set your depth of cut, set your speed and feed, cut. What
more do you want?

"Airy R.Bean" wrote in message
...
Is there a "kink" for setting up a slitting saw to saw through
round bar stock along the axis, so that the slot is exactly
across a diameter? (I presume this to be a similar problem to
setting up accurately for cross-drilling)

This is actually a Ham Radio application; I wish to make
up some very large banana-type plugs from the 1/4" round
bar stock that I have in small quantities. For this, I will need
to saw two diameters in a cross shape, and then splay
out the leaves slightly to make a springy and rubbing contact.

That's the question, how do you set it on center?

--

73
Hank WD5JFR
"CW" wrote in message
...
Set it on center, set your depth of cut, set your speed and feed, cut.
What
more do you want?

"Airy R.Bean" wrote in message
...
Is there a "kink" for setting up a slitting saw to saw through
round bar stock along the axis, so that the slot is exactly
across a diameter? (I presume this to be a similar problem to
setting up accurately for cross-drilling)

This is actually a Ham Radio application; I wish to make
up some very large banana-type plugs from the 1/4" round
bar stock that I have in small quantities. For this, I will need
to saw two diameters in a cross shape, and then splay
out the leaves slightly to make a springy and rubbing contact.

On Fri, 14 Jan 2005 01:46:43 GMT, "Henry Kolesnik"
wrote:

That's the question, how do you set it on center?

Hi Hank,

It seems it's not how, but how well. The how is trivial. The how
well is more a matter of a stock of ¼ inch which is sacrificed to
lumbering gross tools. Modern machines just make errors faster when
it is obviously within the scope of simpler hand tools and jigs. More
time has been expended in the sterile scribblings of what could be, in
place of actually getting it done.

73's
Richard Clark, KB7QHC