Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #11   Report Post  
Old March 28th 05, 03:59 PM
Cecil Moore
 
Posts: n/a
Default

Dave Platt wrote:
... or a link-coupled tuner, which works just fine without a balun


How efficient is link-coupling? I have an old
Sunair PN-099400 auto-tuner that uses motor-
driven variable-link coupling. Too bad it runs
on 28 vdc.
--
73, Cecil http://www.qsl.net/w5dxp

----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----
  #12   Report Post  
Old March 28th 05, 04:52 PM
Cecil Moore
 
Posts: n/a
Default

Dave Platt wrote:
The other approach is to put a choke balun at the input of the tuner,
"float" the tuner chassis clear of ground, and connect the balanced
line directly to the "unbalanced" output of the tuner. This
pseudo-balanced arrangment can provide good balance once the tuner is
adjusted, because the balun "sees" 50 ohms on both sides... but it
adds the complication of having to float and insulate the tuner.


There's considerable debate on that configuration. If we assume
the common-mode current doesn't change when we move the choke
from output to input, i.e. it is a systematic problem, then the
choke is exposed to exactly the same common-mode current on output
and input. Common mode current travels on the tuner chassis and the
coax shield input and coax shield output may be one inch from each
other with a dead short between them.

And here's something that no one, to the best of my knowledge,
has mentioned. If one succeeds in balancing the currents at
the input of an unbalanced antenna tuner, the currents at the
output will automatically be unbalanced because the current on
the coax center wire will suffer a greater phase delay than
the current on the coax inner braid thus forcing some current
to the outside of the coax. This effect should be easy to measure.

Link coupling solves the common-mode problem. Unfortunately, the
MFJ balanced tuners do not relieve the stress on the choke. Take
a look at the schematic to see why.
--
73, Cecil http://www.qsl.net/w5dxp

----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----
  #13   Report Post  
Old March 28th 05, 09:26 PM
Dave Platt
 
Posts: n/a
Default

... or a link-coupled tuner, which works just fine without a balun

How efficient is link-coupling? I have an old
Sunair PN-099400 auto-tuner that uses motor-
driven variable-link coupling. Too bad it runs
on 28 vdc.


I'm not sure that there's any single answer to that question.

Comments on eHam.net from owners of the old Johnson (or Nye) Matchbox
link-coupled tuner seem to suggest that it's capable of operating with
low losses - significantly lower than are achieved by some of the
unbalanced T-configuration tuners mentioned.

I suspect that the efficiency depends very much on the design and
implementation of the tuner (e.g. air-core coils vs. a toroidal
design, size of core, degree of coupling between the tank and the
link, wire gauge) and on the specific impedance being matched.

Based on what I've read about Z-match tuner design, it seems that
close coupling across the inductive link helps boost the efficiency.
However, the close inductive coupling tends to come with an increased
amount of capacitive coupling, and this can apparently affect the
output balance for the worse in some cases.

I suspect (but don't know for sure) that link-coupled designs which
use a fixed-position, tightly-coupled link (e.g. an air-wound or
toroid-core Z-match) may be more efficient than those which use a
"swinging" link with variable coupling.

--
Dave Platt AE6EO
Hosting the Jade Warrior home page: http://www.radagast.org/jade-warrior
I do _not_ wish to receive unsolicited commercial email, and I will
boycott any company which has the gall to send me such ads!
  #14   Report Post  
Old April 3rd 05, 07:30 PM
Reg Edwards
 
Posts: n/a
Default

You'll still need a balun even with a balanced tuner.

Save yourself the expense of a pair of ganged roller coasters.


  #15   Report Post  
Old April 3rd 05, 09:19 PM
Cecil Moore
 
Posts: n/a
Default

Reg Edwards wrote:
You'll still need a balun even with a balanced tuner.


If it's link-coupled, like the Johnson Matchboxes, the
link performs the cancellation of the common-mode current.
--
73, Cecil http://www.qsl.net/w5dxp


----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 100,000 Newsgroups
---= East/West-Coast Server Farms - Total Privacy via Encryption =---
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Inverted ground plane antenna: compared with normal GP and low dipole. Serge Stroobandt, ON4BAA Antenna 8 February 24th 11 10:22 PM
FS: Emtech ZM-1 QRP antenna tuner Larry Gagnon Swap 0 September 12th 04 11:59 PM
FS: Emtech ZM-1 Z-Match QRP antenna tuner Larry Gagnon Swap 0 September 6th 04 05:08 AM
Mobile Ant L match ? Henry Kolesnik Antenna 14 January 20th 04 04:08 AM
QST Article: An Easy to Build, Dual-Band Collinear Antenna Serge Stroobandt, ON4BAA Antenna 12 October 16th 03 07:44 PM


All times are GMT +1. The time now is 04:13 AM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017