Vinnie S. schrieb:

On Tue, 29 Nov 2005 18:14:31 -0000, "The Magnum"
wrote:



"Vinnie S." wrote in message
. ..


On 28 Nov 2005 20:36:15 -0800, "Programbo" wrote:



What does everyone think is the going rate for replacing a blown final
(Output transistor) in a typical CB radio at a repair shop?


If it is the 1969, the part is relatively cheap. The labor is the killer.


I


would think it would be in the area of $50.

Vinnie S.


%*&$ing hell. "how much". 1969's are getting harder to source now since they
have ceased production of them. The 2SC2078 10w transistor is a commonly
used one in the straight 40 type rigs. Even so, id not charge any more than
$25 unless there was a lot more involved than a simple tranny change...but
then again, im not a shop.

Regards,
Graham




Correct, but I think he was getting ripped off, hence $50. I think there is a
better replacement than the 1969,


So there maybe the FCC-type-acceptance will be lost ...for the rare
ones who care about... :-)

Vinnie S." wrote in message
...
On Tue, 29 Nov 2005 18:14:31 -0000, "The Magnum"
wrote:


"Vinnie S." wrote in message
.. .
On 28 Nov 2005 20:36:15 -0800, "Programbo" wrote:

What does everyone think is the going rate for replacing a blown final
(Output transistor) in a typical CB radio at a repair shop?


If it is the 1969, the part is relatively cheap. The labor is the
killer.
I
would think it would be in the area of $50.

Vinnie S.

%*&$ing hell. "how much". 1969's are getting harder to source now since
they
have ceased production of them. The 2SC2078 10w transistor is a commonly
used one in the straight 40 type rigs. Even so, id not charge any more
than
$25 unless there was a lot more involved than a simple tranny
change...but
then again, im not a shop.

Regards,
Graham


Correct, but I think he was getting ripped off, hence $50. I think there
is a
better replacement than the 1969, but don't recall what it was. In any
case, I
would do it myself.

Vinnie S.

Me too. Its a pretty simple job as long as you can use a soldering iron and
you have just an inkling of common sense. The New replacement for the 1969
is an ERF-2030 which is rated at 25w. It might need companion parts
depending on the set up. There's more info on this on the front page of my
website.

Regards,
Graham
--
_._. _... ._. ._ _.. .. _ _ _

Radio is only a Hobby. Don't let it rule your life...

73's - Graham (www.open-channel.co.uk)

"The Magnum" wrote in message
...
Vinnie S." wrote in message
...
On Tue, 29 Nov 2005 18:14:31 -0000, "The Magnum"
wrote:


"Vinnie S." wrote in message
.. .
On 28 Nov 2005 20:36:15 -0800, "Programbo" wrote:

What does everyone think is the going rate for replacing a blown
final
(Output transistor) in a typical CB radio at a repair shop?


If it is the 1969, the part is relatively cheap. The labor is the
killer.
I
would think it would be in the area of $50.

Vinnie S.

%*&$ing hell. "how much". 1969's are getting harder to source now since
they
have ceased production of them. The 2SC2078 10w transistor is a commonly
used one in the straight 40 type rigs. Even so, id not charge any more
than
$25 unless there was a lot more involved than a simple tranny
change...but
then again, im not a shop.

Regards,
Graham


Correct, but I think he was getting ripped off, hence $50. I think there
is a
better replacement than the 1969, but don't recall what it was. In any
case, I
would do it myself.

Vinnie S.

Me too. Its a pretty simple job as long as you can use a soldering iron
and
you have just an inkling of common sense. The New replacement for the 1969
is an ERF-2030 which is rated at 25w. It might need companion parts
depending on the set up. There's more info on this on the front page of my
website.

Regards,
Graham
--


It will need support components unless it is going into a FET based radio
with biasing tactics in place. Also note that the ERF2030 is a IRF520
available for quite cheap, the schematic for the support components is out
there. I am going to start expierimenting next week! I'll let you know how
it turns out!

Chad

On a sunny day (Wed, 30 Nov 2005 18:12:38 -0000) it happened "The Magnum"
wrote in
:

Vinnie S." wrote in message
.. .
On Tue, 29 Nov 2005 18:14:31 -0000, "The Magnum"
wrote:


"Vinnie S." wrote in message
.. .
On 28 Nov 2005 20:36:15 -0800, "Programbo" wrote:

What does everyone think is the going rate for replacing a blown final
(Output transistor) in a typical CB radio at a repair shop?


If it is the 1969, the part is relatively cheap. The labor is the
killer.
I
would think it would be in the area of $50.

Vinnie S.

%*&$ing hell. "how much". 1969's are getting harder to source now since
they
have ceased production of them. The 2SC2078 10w transistor is a commonly
used one in the straight 40 type rigs. Even so, id not charge any more
than
$25 unless there was a lot more involved than a simple tranny
change...but
then again, im not a shop.

Regards,
Graham


Correct, but I think he was getting ripped off, hence $50. I think there
is a
better replacement than the 1969, but don't recall what it was. In any
case, I
would do it myself.

Vinnie S.

Me too. Its a pretty simple job as long as you can use a soldering iron and
you have just an inkling of common sense. The New replacement for the 1969
is an ERF-2030 which is rated at 25w. It might need companion parts
depending on the set up. There's more info on this on the front page of my
website.

Regards,
Graham
Yes it is simple to do, but as to tha tsoldering iron, I repaired a soundcard
for sombody (some lose part).
he then also bought a 'soldering iron', told me, nextr time I will fix this
myself ;-)
Showed me the soldering iron.. it was one of those soldering pistols....
you know the type that heats a thick wire basically to solder.
So 'soldering iron' I have a nice temerature controlled one with a lot
of tips of different shapes.... will keep your PC board and RF parts alive.
Now about that guy how used S39 as soldering flux...
;-)

On Wed, 30 Nov 2005 18:12:38 -0000, "The Magnum"
wrote:

Vinnie S." wrote in message
.. .
On Tue, 29 Nov 2005 18:14:31 -0000, "The Magnum"
wrote:


"Vinnie S." wrote in message
.. .
On 28 Nov 2005 20:36:15 -0800, "Programbo" wrote:

What does everyone think is the going rate for replacing a blown final
(Output transistor) in a typical CB radio at a repair shop?


If it is the 1969, the part is relatively cheap. The labor is the
killer.
I
would think it would be in the area of $50.

Vinnie S.

%*&$ing hell. "how much". 1969's are getting harder to source now since
they
have ceased production of them. The 2SC2078 10w transistor is a commonly
used one in the straight 40 type rigs. Even so, id not charge any more
than
$25 unless there was a lot more involved than a simple tranny
change...but
then again, im not a shop.

Regards,
Graham


Correct, but I think he was getting ripped off, hence $50. I think there
is a
better replacement than the 1969, but don't recall what it was. In any
case, I
would do it myself.

Vinnie S.

Me too. Its a pretty simple job as long as you can use a soldering iron and
you have just an inkling of common sense. The New replacement for the 1969
is an ERF-2030 which is rated at 25w. It might need companion parts
depending on the set up. There's more info on this on the front page of my
website.

Regards,
Graham

Why would we trust your WEB page?

You have this statement on your WEB page:

Remember, connect a busy system as follows,
CB - Pre-amp - SWR meter - Linear - Antenna

Why would you put any SWR meter before the Amp?

If your SWR can't handle the power output of your amp, Do you think
putting it there would give you an accurate reading of the SWR on your
antenna?

In fact I just had to stop typing as I was laughing some more
just thinking about it.. lolol

Regards
Lancer

Volker Tonn sucked off Vinnie S:

snipped

All you have to do to get it fixed for free is to find a ham with at
least an advanced class license. Let the queer ******* suck your dick.
The sick ass ham will fix your cb and service your
cock..............ALL FOR FREE!!!!!!!!!!!!!!!

"Volker Tonn" wrote in message
...
Vinnie S. schrieb:

On Tue, 29 Nov 2005 18:14:31 -0000, "The Magnum"
wrote:



"Vinnie S." wrote in message
. ..


On 28 Nov 2005 20:36:15 -0800, "Programbo" wrote:



What does everyone think is the going rate for replacing a blown final
(Output transistor) in a typical CB radio at a repair shop?


If it is the 1969, the part is relatively cheap. The labor is the
killer.


I


would think it would be in the area of $50.

Vinnie S.


%*&$ing hell. "how much". 1969's are getting harder to source now since
they
have ceased production of them. The 2SC2078 10w transistor is a commonly
used one in the straight 40 type rigs. Even so, id not charge any more
than
$25 unless there was a lot more involved than a simple tranny
change...but
then again, im not a shop.

Regards,
Graham




Correct, but I think he was getting ripped off, hence $50. I think there
is a
better replacement than the 1969,


So there maybe the FCC-type-acceptance will be lost ...for the rare
ones who care about... :-)

A valid point but if its simply changing a transistor im sure there wont be
a problem. Thenagain if its "supertuned" by Mr fiddle merchant at the same
time then that's a different story ;o)

Regards,
Graham
--
_._. _... ._. ._ _.. .. _ _ _

Radio is only a Hobby. Don't let it rule your life...

73's - Graham (www.open-channel.co.uk)

"moparholic" wrote in message
oups.com...

Volker Tonn sucked off Vinnie S:

snipped

All you have to do to get it fixed for free is to find a ham with at
least an advanced class license. Let the queer ******* suck your dick.
The sick ass ham will fix your cb and service your
cock..............ALL FOR FREE!!!!!!!!!!!!!!!


I think id rather pay for the repair ;o)

Regards,
Graham
--
_._. _... ._. ._ _.. .. _ _ _

Radio is only a Hobby. Don't let it rule your life...

73's - Graham (www.open-channel.co.uk)

"Chad Wahls" wrote in message
...

"The Magnum" wrote in message
...
Vinnie S." wrote in message
...
On Tue, 29 Nov 2005 18:14:31 -0000, "The Magnum"
wrote:


"Vinnie S." wrote in message
.. .
On 28 Nov 2005 20:36:15 -0800, "Programbo"
wrote:

What does everyone think is the going rate for replacing a blown
final
(Output transistor) in a typical CB radio at a repair shop?


If it is the 1969, the part is relatively cheap. The labor is the
killer.
I
would think it would be in the area of $50.

Vinnie S.

%*&$ing hell. "how much". 1969's are getting harder to source now
since
they
have ceased production of them. The 2SC2078 10w transistor is a
commonly
used one in the straight 40 type rigs. Even so, id not charge any more
than
$25 unless there was a lot more involved than a simple tranny
change...but
then again, im not a shop.

Regards,
Graham


Correct, but I think he was getting ripped off, hence $50. I think
there
is a
better replacement than the 1969, but don't recall what it was. In any
case, I
would do it myself.

Vinnie S.

Me too. Its a pretty simple job as long as you can use a soldering iron
and
you have just an inkling of common sense. The New replacement for the
1969
is an ERF-2030 which is rated at 25w. It might need companion parts
depending on the set up. There's more info on this on the front page of
my
website.

Regards,
Graham
--


It will need support components unless it is going into a FET based radio
with biasing tactics in place. Also note that the ERF2030 is a IRF520
available for quite cheap, the schematic for the support components is out
there. I am going to start expierimenting next week! I'll let you know
how
it turns out!

Chad

Hi Chad. I for one will be interested in your findings. Let us know.

Regards,
Graham

--
_._. _... ._. ._ _.. .. _ _ _

Radio is only a Hobby. Don't let it rule your life...

73's - Graham (www.open-channel.co.uk)

"Lancer" wrote in message
ews.com...
On Wed, 30 Nov 2005 18:12:38 -0000, "The Magnum"
wrote:

Vinnie S." wrote in message
.. .
On Tue, 29 Nov 2005 18:14:31 -0000, "The Magnum"
wrote:


"Vinnie S." wrote in message
.. .
On 28 Nov 2005 20:36:15 -0800, "Programbo"
wrote:

What does everyone think is the going rate for replacing a blown
final
(Output transistor) in a typical CB radio at a repair shop?


If it is the 1969, the part is relatively cheap. The labor is the
killer.
I
would think it would be in the area of $50.

Vinnie S.

%*&$ing hell. "how much". 1969's are getting harder to source now
since
they
have ceased production of them. The 2SC2078 10w transistor is a
commonly
used one in the straight 40 type rigs. Even so, id not charge any more
than
$25 unless there was a lot more involved than a simple tranny
change...but
then again, im not a shop.

Regards,
Graham


Correct, but I think he was getting ripped off, hence $50. I think
there
is a
better replacement than the 1969, but don't recall what it was. In any
case, I
would do it myself.

Vinnie S.

Me too. Its a pretty simple job as long as you can use a soldering iron
and
you have just an inkling of common sense. The New replacement for the
1969
is an ERF-2030 which is rated at 25w. It might need companion parts
depending on the set up. There's more info on this on the front page of
my
website.

Regards,
Graham

Why would we trust your WEB page?

You dont have to trust it. Its a pointer. If your interested do a websearch
and clarify anything you feel unsure of.

You have this statement on your WEB page:

Remember, connect a busy system as follows,
CB - Pre-amp - SWR meter - Linear - Antenna

Why would you put any SWR meter before the Amp?

Im suprised you question that. What would you think will happen if you shove
150w upwards through a cheap basic SWR meter?

If your SWR can't handle the power output of your amp, Do you think
putting it there would give you an accurate reading of the SWR on your
antenna?

No but its going to be more realistic then it pinging off the scale with
extra power going through it. If its left in line it will also cause much
greater interference than being before the linear. Think about it.

In fact I just had to stop typing as I was laughing some more
just thinking about it.. lolol
Regards
Lancer

Im glad you took the time to look at my site. How's the 23 channel radio
going ;o)

Regards,
Graham
--
_._. _... ._. ._ _.. .. _ _ _

Radio is only a Hobby. Don't let it rule your life...

73's - Graham (www.open-channel.co.uk)