Any Hy-gain Tailtwister guru's lurking about?
 

My meter doesn't display direction any more and I'm trying to figure out
where I should be looking--control box or inside rotator. Everything else
works fine; rotator turns; break works; lights light; etc. The fuse inside
the control box was blown. I replaced it--still no meter indication. Anyone
have any ideas?

tnx

Any Hy-gain Tailtwister guru's lurking about?
 

"KB3DNZ" wrote in message
...
My meter doesn't display direction any more and I'm trying to figure out
where I should be looking--control box or inside rotator. Everything else
works fine; rotator turns; break works; lights light; etc. The fuse inside
the control box was blown. I replaced it--still no meter indication.
Anyone have any ideas?

tnx
Well, is the meter open?

W4ZCB

Any Hy-gain Tailtwister guru's lurking about?
 

If you mean does it indicate at all: When I turn the contol box on the
needle moves to the extreme right position and then falls back slightly. If
I turn the calibration adjustment the needle moves. It just won't track with
the rotator.



"Harold E. Johnson" wrote in message
news:cqiaj.242221$Xa3.173865@attbi_s22...

"KB3DNZ" wrote in message
...
My meter doesn't display direction any more and I'm trying to figure out
where I should be looking--control box or inside rotator. Everything else
works fine; rotator turns; break works; lights light; etc. The fuse
inside the control box was blown. I replaced it--still no meter
indication. Anyone have any ideas?

tnx
Well, is the meter open?

W4ZCB

Any Hy-gain Tailtwister guru's lurking about?
 

"KB3DNZ" wrote in message
...
If you mean does it indicate at all: When I turn the contol box on the
needle moves to the extreme right position and then falls back slightly.
If I turn the calibration adjustment the needle moves. It just won't track
with the rotator.

Open pot in the rotator or open lead in the cable.

W4ZCB

Any Hy-gain Tailtwister guru's lurking about?
 

In article ,
"KB3DNZ" wrote:

If you mean does it indicate at all: When I turn the contol box on the
needle moves to the extreme right position and then falls back slightly. If
I turn the calibration adjustment the needle moves. It just won't track with
the rotator.



"Harold E. Johnson" wrote in message
news:cqiaj.242221$Xa3.173865@attbi_s22...

"KB3DNZ" wrote in message
...
My meter doesn't display direction any more and I'm trying to figure out
where I should be looking--control box or inside rotator. Everything else
works fine; rotator turns; break works; lights light; etc. The fuse
inside the control box was blown. I replaced it--still no meter
indication. Anyone have any ideas?

tnx
Well, is the meter open?

W4ZCB


Open wire, or blown Dashpot up in the rotator.......

Any Hy-gain Tailtwister guru's lurking about?
 

Can I test for either one of these conditions from shack-end of the control
cable?



"You" wrote in message
...
In article ,
"KB3DNZ" wrote:

If you mean does it indicate at all: When I turn the contol box on the
needle moves to the extreme right position and then falls back slightly.
If
I turn the calibration adjustment the needle moves. It just won't track
with
the rotator.



"Harold E. Johnson" wrote in message
news:cqiaj.242221$Xa3.173865@attbi_s22...

"KB3DNZ" wrote in message
...
My meter doesn't display direction any more and I'm trying to figure
out
where I should be looking--control box or inside rotator. Everything
else
works fine; rotator turns; break works; lights light; etc. The fuse
inside the control box was blown. I replaced it--still no meter
indication. Anyone have any ideas?

tnx
Well, is the meter open?

W4ZCB


Open wire, or blown Dashpot up in the rotator.......