I recently bought a Drake TR-4C / RV-4C / AC-4 station
which came from an estate. The gear is nice and clean
and appears to be 100% stock.

After I rebuilt the power supply and replaced a couple
of tubes, the station is operational with the exception
that I have no push-to-talk (PTT). VOX works fine on CW
and SSB. I replaced the 6EV7 tube, and that didn't help.
I tried two different microphones and got the same result
with both of them. Both mics work fine with my B-Line,
so it's not a mic wiring or switching problem. Before I
dive in with a voltmeter, does anyone have any suggestions
on what may be wrong, perhaps based on personal experience?
And yes, I'm aware that the CW key must either be closed
or unplugged for PTT to function.

Thanks and 73,
Dean K5DH

In article ,
K5DH wrote:
I recently bought a Drake TR-4C / RV-4C / AC-4 station
which came from an estate. The gear is nice and clean
and appears to be 100% stock.

After I rebuilt the power supply and replaced a couple
of tubes, the station is operational with the exception
that I have no push-to-talk (PTT). VOX works fine on CW
and SSB. I replaced the 6EV7 tube, and that didn't help.
I tried two different microphones and got the same result
with both of them. Both mics work fine with my B-Line,
so it's not a mic wiring or switching problem. Before I
dive in with a voltmeter, does anyone have any suggestions
on what may be wrong, perhaps based on personal experience?
And yes, I'm aware that the CW key must either be closed
or unplugged for PTT to function.

If you are set for SSB operation and plug a key in, does closing the key
transmit?

I would start looking at the CW key jack and the microphone jack and
the associated wiring.
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."

In article ,
K5DH wrote:
I recently bought a Drake TR-4C / RV-4C / AC-4 station
which came from an estate. The gear is nice and clean
and appears to be 100% stock.

After I rebuilt the power supply and replaced a couple
of tubes, the station is operational with the exception
that I have no push-to-talk (PTT). VOX works fine on CW
and SSB. I replaced the 6EV7 tube, and that didn't help.
I tried two different microphones and got the same result
with both of them. Both mics work fine with my B-Line,
so it's not a mic wiring or switching problem. Before I
dive in with a voltmeter, does anyone have any suggestions
on what may be wrong, perhaps based on personal experience?
And yes, I'm aware that the CW key must either be closed
or unplugged for PTT to function.

If you are set for SSB operation and plug a key in, does closing the key
transmit?

I would start looking at the CW key jack and the microphone jack and
the associated wiring.
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."

In article , says...

In article ,
K5DH wrote:
I recently bought a Drake TR-4C / RV-4C / AC-4 station
which came from an estate. The gear is nice and clean
and appears to be 100% stock.

After I rebuilt the power supply and replaced a couple
of tubes, the station is operational with the exception
that I have no push-to-talk (PTT). VOX works fine on CW
and SSB. I replaced the 6EV7 tube, and that didn't help.
I tried two different microphones and got the same result
with both of them. Both mics work fine with my B-Line,
so it's not a mic wiring or switching problem. Before I
dive in with a voltmeter, does anyone have any suggestions
on what may be wrong, perhaps based on personal experience?
And yes, I'm aware that the CW key must either be closed
or unplugged for PTT to function.


If you are set for SSB operation and plug a key in, does
closing the key transmit?


Nope. Closing the key yields a momentary click of the T/R
relay and that's it.


I would start looking at the CW key jack and the microphone
jack and the associated wiring.
--scott

Already looked at the wiring. Didn't see anything wrong with
it. No evidence it's ever been tampered with, either.

Dean

In article , says...

In article ,
K5DH wrote:
I recently bought a Drake TR-4C / RV-4C / AC-4 station
which came from an estate. The gear is nice and clean
and appears to be 100% stock.

After I rebuilt the power supply and replaced a couple
of tubes, the station is operational with the exception
that I have no push-to-talk (PTT). VOX works fine on CW
and SSB. I replaced the 6EV7 tube, and that didn't help.
I tried two different microphones and got the same result
with both of them. Both mics work fine with my B-Line,
so it's not a mic wiring or switching problem. Before I
dive in with a voltmeter, does anyone have any suggestions
on what may be wrong, perhaps based on personal experience?
And yes, I'm aware that the CW key must either be closed
or unplugged for PTT to function.


If you are set for SSB operation and plug a key in, does
closing the key transmit?


Nope. Closing the key yields a momentary click of the T/R
relay and that's it.


I would start looking at the CW key jack and the microphone
jack and the associated wiring.
--scott

Already looked at the wiring. Didn't see anything wrong with
it. No evidence it's ever been tampered with, either.

Dean

(K5DH) wrote in message ...
In article , says...

In article ,
K5DH wrote:
I recently bought a Drake TR-4C / RV-4C / AC-4 station
which came from an estate. The gear is nice and clean
and appears to be 100% stock.

After I rebuilt the power supply and replaced a couple
of tubes, the station is operational with the exception
that I have no push-to-talk (PTT). VOX works fine on CW
and SSB. I replaced the 6EV7 tube, and that didn't help.
I tried two different microphones and got the same result
with both of them. Both mics work fine with my B-Line,
so it's not a mic wiring or switching problem. Before I
dive in with a voltmeter, does anyone have any suggestions
on what may be wrong, perhaps based on personal experience?
And yes, I'm aware that the CW key must either be closed
or unplugged for PTT to function.


If you are set for SSB operation and plug a key in, does
closing the key transmit?


Nope. Closing the key yields a momentary click of the T/R
relay and that's it.


I would start looking at the CW key jack and the microphone
jack and the associated wiring.
--scott

Already looked at the wiring. Didn't see anything wrong with
it. No evidence it's ever been tampered with, either.

Dean
Hello Dean, I am presently restoring a TR4 and just finished checking
out the mic circuit..On the side of the TR4 you find the first jack
is phones, second one is mic,take a clip lead and short the mic
connector key wire(tip of connector) to ground,it should key up the
relay...tube V19B 6EV7 is Vox tube,it works for Vox and PTT,if vox
works PTT should work also...look at first grid of V19,pin 2,move to
left to junction of R142,R105 and R108 ,key this junction to ground
with test lead,relay should close..Also notice the three resistors
connected to pin 2 are high value 1M, 3.3 M & 6.8 M..Hi value
resistors will always go bad with age,take them loose and check them
with good meter,if they are over 10% hi change them..Be glad to help
if I can , call on phone if you need to... Your old Raytheon friend
Harold W4PQW

(K5DH) wrote in message ...
In article , says...

In article ,
K5DH wrote:
I recently bought a Drake TR-4C / RV-4C / AC-4 station
which came from an estate. The gear is nice and clean
and appears to be 100% stock.

After I rebuilt the power supply and replaced a couple
of tubes, the station is operational with the exception
that I have no push-to-talk (PTT). VOX works fine on CW
and SSB. I replaced the 6EV7 tube, and that didn't help.
I tried two different microphones and got the same result
with both of them. Both mics work fine with my B-Line,
so it's not a mic wiring or switching problem. Before I
dive in with a voltmeter, does anyone have any suggestions
on what may be wrong, perhaps based on personal experience?
And yes, I'm aware that the CW key must either be closed
or unplugged for PTT to function.


If you are set for SSB operation and plug a key in, does
closing the key transmit?


Nope. Closing the key yields a momentary click of the T/R
relay and that's it.


I would start looking at the CW key jack and the microphone
jack and the associated wiring.
--scott

Already looked at the wiring. Didn't see anything wrong with
it. No evidence it's ever been tampered with, either.

Dean
Hello Dean, I am presently restoring a TR4 and just finished checking
out the mic circuit..On the side of the TR4 you find the first jack
is phones, second one is mic,take a clip lead and short the mic
connector key wire(tip of connector) to ground,it should key up the
relay...tube V19B 6EV7 is Vox tube,it works for Vox and PTT,if vox
works PTT should work also...look at first grid of V19,pin 2,move to
left to junction of R142,R105 and R108 ,key this junction to ground
with test lead,relay should close..Also notice the three resistors
connected to pin 2 are high value 1M, 3.3 M & 6.8 M..Hi value
resistors will always go bad with age,take them loose and check them
with good meter,if they are over 10% hi change them..Be glad to help
if I can , call on phone if you need to... Your old Raytheon friend
Harold W4PQW

On Fri, 09 Jul 2004 15:15:39 GMT, (K5DH) wrote:

I recently bought a Drake TR-4C / RV-4C / AC-4 station
which came from an estate. The gear is nice and clean
and appears to be 100% stock.

After I rebuilt the power supply and replaced a couple
of tubes, the station is operational with the exception
that I have no push-to-talk (PTT). VOX works fine on CW
and SSB. I replaced the 6EV7 tube, and that didn't help.
I tried two different microphones and got the same result
with both of them. Both mics work fine with my B-Line,
so it's not a mic wiring or switching problem. Before I
dive in with a voltmeter, does anyone have any suggestions
on what may be wrong, perhaps based on personal experience?
And yes, I'm aware that the CW key must either be closed
or unplugged for PTT to function.

Thanks and 73,
Dean K5DH


Dean,

Have you replaced the 6FQ7? This tube controls the TX/RX.

Walt, KA2NJF

On Fri, 09 Jul 2004 15:15:39 GMT, (K5DH) wrote:

I recently bought a Drake TR-4C / RV-4C / AC-4 station
which came from an estate. The gear is nice and clean
and appears to be 100% stock.

After I rebuilt the power supply and replaced a couple
of tubes, the station is operational with the exception
that I have no push-to-talk (PTT). VOX works fine on CW
and SSB. I replaced the 6EV7 tube, and that didn't help.
I tried two different microphones and got the same result
with both of them. Both mics work fine with my B-Line,
so it's not a mic wiring or switching problem. Before I
dive in with a voltmeter, does anyone have any suggestions
on what may be wrong, perhaps based on personal experience?
And yes, I'm aware that the CW key must either be closed
or unplugged for PTT to function.

Thanks and 73,
Dean K5DH


Dean,

Have you replaced the 6FQ7? This tube controls the TX/RX.

Walt, KA2NJF

In article ,
says...

On Fri, 09 Jul 2004 15:15:39 GMT, (K5DH) wrote:

I recently bought a Drake TR-4C / RV-4C / AC-4 station
which came from an estate. The gear is nice and clean
and appears to be 100% stock.

After I rebuilt the power supply and replaced a couple
of tubes, the station is operational with the exception
that I have no push-to-talk (PTT). VOX works fine on CW
and SSB. I replaced the 6EV7 tube, and that didn't help.
I tried two different microphones and got the same result
with both of them. Both mics work fine with my B-Line,
so it's not a mic wiring or switching problem. Before I
dive in with a voltmeter, does anyone have any suggestions
on what may be wrong, perhaps based on personal experience?
And yes, I'm aware that the CW key must either be closed
or unplugged for PTT to function.

Thanks and 73,
Dean K5DH


Dean,

Have you replaced the 6FQ7? This tube controls the TX/RX.

Walt, KA2NJF


Hi Walt,

The TR-4C uses a 6EV7 instead of the 6FQ7 used in the
earlier models. Thanks for the help attempt!

73,
Dean K5DH