"Andy in NJ" SHORECOGS at COMCAST DOT NET wrote in message
...


--
73! de Andy KC2SSB
http://shorecogs.tripod.com
AIM: shorecogs
"L." wrote in message
erio.net...
There are Smeters to be had - new - out there, but you have to make sure
they'll fit physically and so on. Not all are created equal. You may or
may not be

Actually, I need the light bulb for the meter, not the actual meter
itself. I am sure there are non-CB stores that have this part, as it is
probably a common part used in many radios. I just don't know where to
look.

I can't recall at the moment what type of "Channel" display they used,
I'm thinking a small PC board with a dual display - perhaps a couple
other components and a flex circuit strip coming from it. IF it is "just"
the dual display, you should be able to get that. I don't know how you're
fixed for local sources. Some on here may have them. As for me, I'd have
to check the stock to see if I have any to fit the need (of those in
stock) - once I confirmed what was actually used. .

I found a place on the net that sells the display. With shipping it comes
to less than $10, no biggie. The display flickers in and out. Might even
be a solder joint - never took the time to check, which I probably should
have.

The other parts like the pilot lights and such shouldn't be too hard for
you to acquire. Even Rad Shack may have them in their bins in a store -
or something useable. They may have said those "part numbers" are no
longer in stock - but that isn't to say they may not be able to be
substituted. Many "sales" people that handle this sort of stuff don't
know a diode from a transistor either especially for subbing, so don't
press your luck trying to get help there.

Basically, the Drone at Rat Shack told me that if it's not in the
computer, there's no way to tell what other parts may be compatable. He
did ask if I needed a cell phone, though (nah, just kidding, he didn't
ask that, but I thought I'd throw it in ).


That last part kills me... Of course the computer couldn't tell them what is
compatible or not, it isn't taught electronics knowledge - nor programmed
with subs in "MOST" cases. They "may" have subs for some things, but not for
components like that. What an assinine answer. Basically, all it says is
stock number such and such, price, in stock or out. They CAN pull up some
manuals to show parts used, but they do NOT list subs. That system can't
tell you jack **** when it comes to subbing parts.

As to your display, may be a bad solder joint - as you suspect. Check it
before spending cash for the display - unless of course you just want to go
ahead and buy one as a spare. As to the Smeter, is the bulb on the order of
a wheat lamp or does it look like a fuse? I haven't looked the radio up to
know, but I'm betting its a wheat style lamp with leads. Those are available
at the shack in their parts bins. About 99 cents for a pack of 2 if I
recall.

As I said, don't count on them to help. Most don't know their ass from a
hole in the ground. They wouldn't know a resistor from a Diode to start
with, so they sure in hell couldn't help with a Sub. There are some stores
which have some who know - but not many. Of the 5 stores I've been to and
all their workers, I've only found 3 people who knew anything about
electronics. Sure makes ya wonder why the Board of Directors allowed them to
take on the slogan "You've got questions, we've got answers". You can't
possibly have answers when the majority of your employees aren't
electronically inclined. What is funny, is I'll make up a list with stock
numbers to give to my g/f to take to the shack and they'll question her as
to whether she's buying the right parts! How the hell would they know - they
have no clue what I'm using them for. IF they were electronically inclined,
they probably wouldn't be working there - anyway! The store couldn't afford
to keep them.

I don't think it matters much anymore anyway, I've seen where their
components are selling for 50% off. Must be trying to rid the stores of them
once and for all.

I don't get asked too often about the cell phone. Of course, I usually have
mine on my belt in open view. I do it on purpose - just so I WON'T hear it.

Good luck in acquiring your parts!

L.

On Thu, 11 Nov 2004 20:17:49 -0500, "Andy in NJ" SHORECOGS at COMCAST
DOT NET wrote:

Try www.mouser.com or call 'em at 800-346-6873. They list all kinds of
illumination devices -- check their product index under
"illumination".

bob
k5qwg

On Thu, 11 Nov 2004 20:17:49 -0500, "Andy in NJ" SHORECOGS at COMCAST
DOT NET wrote:

Try www.mouser.com or call 'em at 800-346-6873. They list all kinds of
illumination devices -- check their product index under
"illumination".

bob
k5qwg

--
73! de Andy KC2SSB
http://shorecogs.tripod.com
AIM: shorecogs
"L." wrote in message
erio.net...
There are Smeters to be had - new - out there, but you have to make sure
they'll fit physically and so on. Not all are created equal. You may or may
not be

Actually, I need the light bulb for the meter, not the actual meter itself.
I am sure there are non-CB stores that have this part, as it is probably a
common part used in many radios. I just don't know where to look.

I can't recall at the moment what type of "Channel" display they used, I'm
thinking a small PC board with a dual display - perhaps a couple other
components and a flex circuit strip coming from it. IF it is "just" the
dual display, you should be able to get that. I don't know how you're
fixed for local sources. Some on here may have them. As for me, I'd have
to check the stock to see if I have any to fit the need (of those in
stock) - once I confirmed what was actually used. .

I found a place on the net that sells the display. With shipping it comes to
less than $10, no biggie. The display flickers in and out. Might even be a
solder joint - never took the time to check, which I probably should have.

The other parts like the pilot lights and such shouldn't be too hard for
you to acquire. Even Rad Shack may have them in their bins in a store - or
something useable. They may have said those "part numbers" are no longer
in stock - but that isn't to say they may not be able to be substituted.
Many "sales" people that handle this sort of stuff don't know a diode from
a transistor either especially for subbing, so don't press your luck
trying to get help there.

Basically, the Drone at Rat Shack told me that if it's not in the computer,
there's no way to tell what other parts may be compatable. He did ask if I
needed a cell phone, though (nah, just kidding, he didn't ask that, but I
thought I'd throw it in ).

--
73! de Andy KC2SSB
http://shorecogs.tripod.com
AIM: shorecogs
"L." wrote in message
erio.net...
There are Smeters to be had - new - out there, but you have to make sure
they'll fit physically and so on. Not all are created equal. You may or may
not be

Actually, I need the light bulb for the meter, not the actual meter itself.
I am sure there are non-CB stores that have this part, as it is probably a
common part used in many radios. I just don't know where to look.

I can't recall at the moment what type of "Channel" display they used, I'm
thinking a small PC board with a dual display - perhaps a couple other
components and a flex circuit strip coming from it. IF it is "just" the
dual display, you should be able to get that. I don't know how you're
fixed for local sources. Some on here may have them. As for me, I'd have
to check the stock to see if I have any to fit the need (of those in
stock) - once I confirmed what was actually used. .

I found a place on the net that sells the display. With shipping it comes to
less than $10, no biggie. The display flickers in and out. Might even be a
solder joint - never took the time to check, which I probably should have.

The other parts like the pilot lights and such shouldn't be too hard for
you to acquire. Even Rad Shack may have them in their bins in a store - or
something useable. They may have said those "part numbers" are no longer
in stock - but that isn't to say they may not be able to be substituted.
Many "sales" people that handle this sort of stuff don't know a diode from
a transistor either especially for subbing, so don't press your luck
trying to get help there.

Basically, the Drone at Rat Shack told me that if it's not in the computer,
there's no way to tell what other parts may be compatable. He did ask if I
needed a cell phone, though (nah, just kidding, he didn't ask that, but I
thought I'd throw it in ).

"=K=5=D=H=" wrote in message
...
Andy,

Try a CB repair shop. Any shop that does repair work will typically have
a
"boneyard" of dead radios in their back room or storage shed. A good bet
would
be a shop located at a truck stop on the interstate. When a trucker's CB
quits, they usually just buy a new one and abandon the old one at the
shop.
Sometimes the dealers repair and re-sell them, but often they just toss
'em on
the pile.

73,
Dean K5DH

In article , SHORECOGSatCOMCASTDOTNET
says...

Hello. I need a couple of components for a Realistic TRC-458. I checked
with
Radio Shack and the parts are no longer available. Can anyone suggest a
source for these parts:

Item D401 (LED), Part #L-0776, Channel Display (TLR321)
Item PL401 (Lamp), Part #L-0786, S/RF Meter (11.73v @ 43mA)

--
73! de Andy KC2SSB
http://shorecogs.tripod.com
AIM: shorecogs




Check the rec.radio.cb group..... that is a better bet! I have to look, I
"may" have a similar radio for parts, not sure. As the other poster said -
most shops have a bone yard of CBs. I do as well for CBs, VCRs and other
items, but can't remember all the radios tossed in. As far as buying some of
those parts new - though it may not be impossible - it can be tedious. There
are Smeters to be had - new - out there, but you have to make sure they'll
fit physically and so on. Not all are created equal. You may or may not be
able to get all parts in one place. In the case you can't, man those
shipping charges could rack up! And some places want minimum orders.
Hopefully, you can find a radio chassis to fit your needs. I'll look around
here to see what is here.

I can't recall at the moment what type of "Channel" display they used, I'm
thinking a small PC board with a dual display - perhaps a couple other
components and a flex circuit strip coming from it. IF it is "just" the dual
display, you should be able to get that. I don't know how you're fixed for
local sources. Some on here may have them. As for me, I'd have to check the
stock to see if I have any to fit the need (of those in stock) - once I
confirmed what was actually used. .

The other parts like the pilot lights and such shouldn't be too hard for
you to acquire. Even Rad Shack may have them in their bins in a store - or
something useable. They may have said those "part numbers" are no longer in
stock - but that isn't to say they may not be able to be substituted. Many
"sales" people that handle this sort of stuff don't know a diode from a
transistor either especially for subbing, so don't press your luck trying to
get help there.

--
C.L. FURLONG ENTERPRISES
P.O. Box 289
514 Railroad Street
Stockdale, PA 15483

Phone: 724-938-7808
E-Mail:

Electronics Div. - 2 way/CB/Ham Repairs - Sales, Parts, FCC License
Assistance and Exams.
Gift Div. - Gifts for all occasions, Gift Certificates, Fund Raiser Programs
available.

Daily specials available also - on stock over-runs, trade-ins, etc. New and
Used - Sold AS IS.

Cash/Money Orders/Pay -Pal/Checks (with valid ID - otherwise 2 weeks for
clearance)

Catalogs/Flyers available. Watch for our products in Newsgroups, E-Bay, Swap
Meets!
Of course, we also have the shop - be glad to meet you - here or there!
************************************************** ********************

"=K=5=D=H=" wrote in message
...
Andy,

Try a CB repair shop. Any shop that does repair work will typically have
a
"boneyard" of dead radios in their back room or storage shed. A good bet
would
be a shop located at a truck stop on the interstate. When a trucker's CB
quits, they usually just buy a new one and abandon the old one at the
shop.
Sometimes the dealers repair and re-sell them, but often they just toss
'em on
the pile.

73,
Dean K5DH

In article , SHORECOGSatCOMCASTDOTNET
says...

Hello. I need a couple of components for a Realistic TRC-458. I checked
with
Radio Shack and the parts are no longer available. Can anyone suggest a
source for these parts:

Item D401 (LED), Part #L-0776, Channel Display (TLR321)
Item PL401 (Lamp), Part #L-0786, S/RF Meter (11.73v @ 43mA)

--
73! de Andy KC2SSB
http://shorecogs.tripod.com
AIM: shorecogs




Check the rec.radio.cb group..... that is a better bet! I have to look, I
"may" have a similar radio for parts, not sure. As the other poster said -
most shops have a bone yard of CBs. I do as well for CBs, VCRs and other
items, but can't remember all the radios tossed in. As far as buying some of
those parts new - though it may not be impossible - it can be tedious. There
are Smeters to be had - new - out there, but you have to make sure they'll
fit physically and so on. Not all are created equal. You may or may not be
able to get all parts in one place. In the case you can't, man those
shipping charges could rack up! And some places want minimum orders.
Hopefully, you can find a radio chassis to fit your needs. I'll look around
here to see what is here.

I can't recall at the moment what type of "Channel" display they used, I'm
thinking a small PC board with a dual display - perhaps a couple other
components and a flex circuit strip coming from it. IF it is "just" the dual
display, you should be able to get that. I don't know how you're fixed for
local sources. Some on here may have them. As for me, I'd have to check the
stock to see if I have any to fit the need (of those in stock) - once I
confirmed what was actually used. .

The other parts like the pilot lights and such shouldn't be too hard for
you to acquire. Even Rad Shack may have them in their bins in a store - or
something useable. They may have said those "part numbers" are no longer in
stock - but that isn't to say they may not be able to be substituted. Many
"sales" people that handle this sort of stuff don't know a diode from a
transistor either especially for subbing, so don't press your luck trying to
get help there.

--
C.L. FURLONG ENTERPRISES
P.O. Box 289
514 Railroad Street
Stockdale, PA 15483

Phone: 724-938-7808
E-Mail:

Electronics Div. - 2 way/CB/Ham Repairs - Sales, Parts, FCC License
Assistance and Exams.
Gift Div. - Gifts for all occasions, Gift Certificates, Fund Raiser Programs
available.

Daily specials available also - on stock over-runs, trade-ins, etc. New and
Used - Sold AS IS.

Cash/Money Orders/Pay -Pal/Checks (with valid ID - otherwise 2 weeks for
clearance)

Catalogs/Flyers available. Watch for our products in Newsgroups, E-Bay, Swap
Meets!
Of course, we also have the shop - be glad to meet you - here or there!
************************************************** ********************

I found the channel display, now I just need the light bulb. Anyone got any
ideas?

--
73! de Andy KC2SSB
http://shorecogs.tripod.com
AIM: shorecogs

"Andy in NJ" SHORECOGS at COMCAST DOT NET wrote in message
...
Hello. I need a couple of components for a Realistic TRC-458. I checked
with Radio Shack and the parts are no longer available. Can anyone suggest
a source for these parts:

Item D401 (LED), Part #L-0776, Channel Display (TLR321)
Item PL401 (Lamp), Part #L-0786, S/RF Meter (11.73v @ 43mA)

--
73! de Andy KC2SSB
http://shorecogs.tripod.com
AIM: shorecogs

In article , "Andy in NJ" SHORECOGS
at COMCAST DOT NET says...

Hello. I need a couple of components for a Realistic TRC-458. I checked with
Radio Shack and the parts are no longer available. Can anyone suggest a
source for these parts:

Item D401 (LED), Part #L-0776, Channel Display (TLR321)
Item PL401 (Lamp), Part #L-0786, S/RF Meter (11.73v @ 43mA)

Suggestion: Look for a generic replacement for the LED display
(I'd wager it's just a seven-segment unit), and replace the pilot light
with a LED (use a super-bright if it's for a backlight, and a standard
one if it's just a front-panel pilot light).

Happy hunting.

--
Dr. Anton T. Squeegee, Director, Dutch Surrealist Plumbing Institute.
(Known to some as Bruce Lane, ARS KC7GR,
kyrrin (a/t) bluefeathertech[d=o=t]calm -- www.bluefeathertech.com
"If Salvador Dali had owned a computer, would it have been equipped
with surreal ports?"

Andy,

Try a CB repair shop. Any shop that does repair work will typically have a
"boneyard" of dead radios in their back room or storage shed. A good bet would
be a shop located at a truck stop on the interstate. When a trucker's CB
quits, they usually just buy a new one and abandon the old one at the shop.
Sometimes the dealers repair and re-sell them, but often they just toss 'em on
the pile.

73,
Dean K5DH

In article , SHORECOGSatCOMCASTDOTNET
says...

Hello. I need a couple of components for a Realistic TRC-458. I checked
with
Radio Shack and the parts are no longer available. Can anyone suggest a
source for these parts:

Item D401 (LED), Part #L-0776, Channel Display (TLR321)
Item PL401 (Lamp), Part #L-0786, S/RF Meter (11.73v @ 43mA)

--
73! de Andy KC2SSB
http://shorecogs.tripod.com
AIM: shorecogs