I've never seen anything with a posidrive screw in it.. They aren't used
very much in the USA or at least in Florida... I have yet to need a
posidrive screwdriver and I've taken all kinds of things apart in my life..
I consider a good set of torx and allen wrenches a necessity along with a
set of sockets and wrenches and of course a small set of jewlers
screwdrivers and mini torx bits, hammers, saws, etc...

The funny thing is I never knew what that weird looking phillips bit I had
was called until today.

- Mike

"Fred McKenzie" wrote in message
...
In article , Roy Lewallen
wrote:

I'd consider looking for some other tool dealers to do business with.
Pozidriv (a registered trademark of Phillips Screw Co.) screws and
drivers are very common, sold by just about every tool company from
Snap-on through Stanley to Sears.


OK Guys! I've done some more checking, and still can't find a store that
sells Posidrive or Pozidrive. I have one lead to a specialty tool store
across the state, but the local Ace, Sears and Lowes don't carry either
the screws or the drivers.

I can see where the Posidrive may be used in some electronic equipment,
but all of the screws in the hinges in my house, as well as the screws
holding the locks on the doors, are definitely Phillips. Are Posidrive
screws used for those applications in other countries?

I can see now that my original list should have stopped without the
additional items. The purpose was to define a really BASIC set of tools
for use around the home!

Fred

"Fred McKenzie" wrote in message
...
In article , Highland Ham
wrote:

What about Posidrive screwdrivers ? These are similar to Philips type of
screwdrivers but have additional 'notches' (if that is the correct word)
for better grip . The relevant screw heads are accordingly.

Frank-

I've heard of Posidrive. I think they are used in an old Hewlett Packard
counter I have. However, the tool dealers I asked had never heard of
them. I ended up using a common Phillips driver for my counter.

Certainly Posidrive would be a better choice where they are more commonly
used.

Fred

In that vein, Canadians would have Robertson screwdrivers in their basic
toolbox for home use. Described, with history, at
http://en.wikipedia.org/wiki/Robertson_screwdriver .

Tom

Tom Holden wrote:

"Fred McKenzie" wrote in message
...
In article , Highland Ham
wrote:

What about Posidrive screwdrivers ? These are similar to Philips type of
screwdrivers but have additional 'notches' (if that is the correct word)
for better grip . The relevant screw heads are accordingly.

Frank-

I've heard of Posidrive. I think they are used in an old Hewlett Packard
counter I have. However, the tool dealers I asked had never heard of
them. I ended up using a common Phillips driver for my counter.

Certainly Posidrive would be a better choice where they are more commonly
used.

Fred

In that vein, Canadians would have Robertson screwdrivers in their basic
toolbox for home use. Described, with history, at
http://en.wikipedia.org/wiki/Robertson_screwdriver .

Tom

I despise Robertson screws, along with the "Clutch head" screws.
Every time I run into either of them, someone has put them in with a
worn bit that strips the head and makes them almost impossible to
remove. I've used surface grinders, drills, and a cutting torch to
remove them to make repairs. I generally replace them with hex head
screws and make sure that I always inspect the bit before I start a job.
--
Service to my country? Been there, Done that, and I've got my DD214 to
prove it.
Member of DAV #85.

Michael A. Terrell
Central Florida

ORIGINAL MESSAGE:

On Tue, 25 Apr 2006 04:39:30 GMT, "Michael A. Terrell"
wrote:

I've used surface grinders, drills, and a cutting torch to
remove them to make repairs.

*********** REPLY SEPARATOR ***********

Often a Dremel tool with a thin grinding wheel will allow you to make
a slot and then use a regular screwdriver to remove it.

Bill, W6WRT

I hate those stupid robitson bits too... Like you said they always seem to
be stripped off...


"Michael A. Terrell" wrote in message
...
Tom Holden wrote:

"Fred McKenzie" wrote in message
...
In article , Highland Ham
wrote:

What about Posidrive screwdrivers ? These are similar to Philips type
of
screwdrivers but have additional 'notches' (if that is the correct
word)
for better grip . The relevant screw heads are accordingly.

Frank-

I've heard of Posidrive. I think they are used in an old Hewlett
Packard
counter I have. However, the tool dealers I asked had never heard of
them. I ended up using a common Phillips driver for my counter.

Certainly Posidrive would be a better choice where they are more
commonly
used.

Fred

In that vein, Canadians would have Robertson screwdrivers in their basic
toolbox for home use. Described, with history, at
http://en.wikipedia.org/wiki/Robertson_screwdriver .

Tom

I despise Robertson screws, along with the "Clutch head" screws.
Every time I run into either of them, someone has put them in with a
worn bit that strips the head and makes them almost impossible to
remove. I've used surface grinders, drills, and a cutting torch to
remove them to make repairs. I generally replace them with hex head
screws and make sure that I always inspect the bit before I start a job.
--
Service to my country? Been there, Done that, and I've got my DD214 to
prove it.
Member of DAV #85.

Michael A. Terrell
Central Florida

"Michael A. Terrell" wrote in message
...
I despise Robertson screws, along with the "Clutch head" screws.
Every time I run into either of them, someone has put them in with a
worn bit that strips the head and makes them almost impossible to
remove. I've used surface grinders, drills, and a cutting torch to
remove them to make repairs. I generally replace them with hex head
screws and make sure that I always inspect the bit before I start a job.
--

Misdirected feelings - should be towards worn bits of all types that can
mess up all types of screws. Don't blame the screw for the fault of the bit
and the recklessness of the user. Among the three common wood screws here
(slot, Phillips and Robertson), I'll take the Robbie anyday. The ability of
the bit to retain the screw is a big advantage.

Tom

Fred McKenzie wrote:
Most everyone has a screwdriver or two laying around the house, but not
everyone has a minimum collection stored in a tool box. If you know a
young person graduating from high school, a single relative, or even
yourself, a tool box with a minimum complement of tools may be the perfect
gift.

Based on my own experience, the BASIC TOOL BOX should include:

A plastic or metal box such as the 13² plastic box from Walmart or the 14²
plastic box from Lowes. The box should have a secure latch that won¹t
come open when picked up.

#1 Philips screwdriver

#2 Philips screwdriver

1/8² Flat blade screwdriver

1/4² Flat blade screwdriver

Standard pair of slip-joint pliers with insulated handle

Diagonal cutters with insulated handle

Long nose pliers with side cutter and insulated handle

Small claw hammer such as Sears 3805 - 7 oz.

Depending on your knowledge of the individual¹s needs and the size of the
box, additional items might include:

Full-size hammer

Crowbar or pry-lever

Flashlight

Tire pressure gauge(s)

Pocket knife & sharpening stone

Soldering iron & solder & soldering braid

Digital multimeter

Set of nut drivers

Set of Allen wrenches

Set of Torx drivers

You get the idea!

73, Fred, K4DII

Dunno why it didn't occur to me...thankfully it 'did' occur to my wife:
Bought almost the exact (above) setup for my prospective son-in-law
for Christmas. He's mechanically dis-inclined. We're gonna fix that.
Can't have a s-in-l who can't fix stuff....

jak

And... You plan to work on SMD circuit boards with this!!!


Jerry G.
======

"Jerry G." wrote:

And... You plan to work on SMD circuit boards with this!!!

Jerry G.
======


I see that you still have reading comprehension problems, Jerry.
Anyway, no one in their right mind would try to cram a good SMD rework
station into any toobox. There is no way I would let anyone shove a
stereo microscope into a toolbox.


--
Service to my country? Been there, Done that, and I've got my DD214 to
prove it.
Member of DAV #85.

Michael A. Terrell
Central Florida

And... You plan to work on SMD circuit boards with this!!!


Jerry G.
======