Searching for a component source...
 

I'm searching for a source/supplier for a component. I'm not looking
to buy from someone here, but simply a source for a part for a
project. It is a "through-hole" mount pushbutton switch. It needs to
be a maintained contact, push-on push-off, SPST, 5a or better rating.
The hole diameter needs to be 3/8" (of slightly less), and I'd like it
to have a rubber boot on the button to help keep water out.

Any ideas? I've been searching high and low, in digi-key, mcmaster,
radio shack, etc...but no luck. Tried every parts book I have... have
seen them in the past, but don't remember the company who made them.

Thanks,
Dave WB4IUY

Searching for a component source...
 

"Dave WB4IUY" wrote in message
oups.com...
I'm searching for a source/supplier for a component. I'm not looking
to buy from someone here, but simply a source for a part for a
project. It is a "through-hole" mount pushbutton switch. It needs to
be a maintained contact, push-on push-off, SPST, 5a or better rating.
The hole diameter needs to be 3/8" (of slightly less), and I'd like it
to have a rubber boot on the button to help keep water out.

Any ideas? I've been searching high and low, in digi-key, mcmaster,
radio shack, etc...but no luck. Tried every parts book I have... have
seen them in the past, but don't remember the company who made them.

Thanks,
Dave WB4IUY



You could also try Jameco, MCM Electronics or Mouser Electronics.

Searching for a component source...
 

It occurs to me that if you dont want to buy from "someone here" you negated
a source !
Having said that, the marine industry has many sources.....also industrial
distributers such as "Allied"....get an industrial trade publication and
request the bingo cards promoted in the rear sections.

Henry

"Dave WB4IUY" wrote in message
oups.com...
I'm searching for a source/supplier for a component. I'm not looking
to buy from someone here, but simply a source for a part for a
project. It is a "through-hole" mount pushbutton switch. It needs to
be a maintained contact, push-on push-off, SPST, 5a or better rating.
The hole diameter needs to be 3/8" (of slightly less), and I'd like it
to have a rubber boot on the button to help keep water out.

Any ideas? I've been searching high and low, in digi-key, mcmaster,
radio shack, etc...but no luck. Tried every parts book I have... have
seen them in the past, but don't remember the company who made them.

Thanks,
Dave WB4IUY

Searching for a component source...
 

In article .com,
Dave WB4IUY wrote:
I'm searching for a source/supplier for a component. I'm not looking
to buy from someone here, but simply a source for a part for a
project. It is a "through-hole" mount pushbutton switch. It needs to
be a maintained contact, push-on push-off, SPST, 5a or better rating.
The hole diameter needs to be 3/8" (of slightly less), and I'd like it
to have a rubber boot on the button to help keep water out.

The first place I would look is a marine supply place. If you are not
in a boating area, check:

http://www.westmarine.com
or
http://www.boatersworld.com

and many others.

Also check an electrical supply house or graybar: http://www.graybar.com

--
Rich Greenberg N Ft Myers, FL, USA richgr atsign panix.com + 1 239 543 1353
Eastern time. N6LRT I speak for myself & my dogs only. VM'er since CP-67
Canines:Val, Red, Shasta & Casey (RIP), Red & Zero, Siberians Owner:Chinook-L
Retired at the beach Asst Owner:Sibernet-L

Searching for a component source...
 

On Apr 20, 8:45 am, "Henry" wrote:
It occurs to me that if you dont want to buy from "someone here" you negated
a source !
Henry

Thanks for the info, Henry. There's an issue with the rules of this
forum with buying/selling stuff, so I just wanted to make it clear
that I was looking for the source for a part, not trying to start a
swapshop of some sort on this forum.

Thanks,
Dave Wb4IUY