| Home |
| Search |
| Today's Posts |
|
#1
February 4th 05, 11:20 PM
|
|||
|
|||
Discriminator tap for BC895XLT Needed
Can someone tell me the proper tap off procedure for the BC895? I have
found-I think-the correct tap off point but the audio is severely affected on speaker output if I feed it to a sound card. Steve |
|
#2
February 5th 05, 07:22 AM
|
|||
|
|||
|
On Fri, 04 Feb 2005 23:20:24 GMT, (Steven Fritts)
wrote: Can someone tell me the proper tap off procedure for the BC895? I have found-I think-the correct tap off point but the audio is severely affected on speaker output if I feed it to a sound card. According to http://www.discriminator.nl/ic/ it should be pin 9 of the MC13371. Did you tap the right point? -- Cabin crew: yellow door selectors automatic |
|
#3
February 5th 05, 08:30 PM
|
|||
|
|||
|
not sure, but THANK YOU for the info!!! Do I need to use any dropping resistor or make up a network to isolate it from the sound card input impedance?? On Sat, 05 Feb 2005 08:22:13 +0100, Brengsek! wrote: On Fri, 04 Feb 2005 23:20:24 GMT, (Steven Fritts) wrote: Can someone tell me the proper tap off procedure for the BC895? I have found-I think-the correct tap off point but the audio is severely affected on speaker output if I feed it to a sound card. According to http://www.discriminator.nl/ic/ it should be pin 9 of the MC13371. Did you tap the right point? -- Cabin crew: yellow door selectors automatic |
|
#5
February 6th 05, 02:40 AM
|
|||
|
|||
|
THANK YOU!
Steve On Sat, 05 Feb 2005 23:57:27 +0100, Brengsek! wrote: On Sat, 05 Feb 2005 20:30:22 GMT, (Steven Fritts) wrote: Can someone tell me the proper tap off procedure for the BC895? I have found-I think-the correct tap off point but the audio is severely affected on speaker output if I feed it to a sound card. According to http://www.discriminator.nl/ic/ it should be pin 9 of the MC13371. Did you tap the right point? not sure, but THANK YOU for the info!!! Do I need to use any dropping resistor or make up a network to isolate it from the sound card input impedance?? I always use a resistor between 5k6 and 15k, but that's merely to protect the discriminator output from short circuiting during (un)plugging. Rene -- Cabin crew: yellow door selectors automatic |
|
#6
February 6th 05, 08:14 AM
|
|||
|
|||
|
On Sat, 05 Feb 2005 23:57:27 +0100, Brengsek! wrote:
Do I need to use any dropping resistor or make up a network to isolate it from the sound card input impedance?? I always use a resistor between 5k6 and 15k, but that's merely to protect the discriminator output from short circuiting during (un)plugging. To be precise, I should write that I use a resistor to protect the receiver's discriminator when the output is short circuited during (un)plugging. -- Cabin crew: yellow door selectors automatic |
| Reply |
| Thread Tools | Search this Thread |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| VOA Delano: 1. Uses Rhombics (still!) 2. Staff needed instructions on not getting fried! | Shortwave | |||
| 60 meter mod info needed... | Equipment | |||
| Needed "data processing magazine" also any of same topic are from 50's 60's 70's such as "Datamation", ACM conference proceedings, Early AFIPS, and others. | Equipment | |||
| WTB: Needed: charger(s) for Motorola Spirit 2-way radio(s) | Scanner | |||
| Manual Needed for NCG 10/160M AKA National (Panasonic) RJX-810D | Equipment | |||
Linear Mode
