LinkBack Thread Tools Search this Thread Display Modes
Prev Previous Post   Next Post Next
  #14   Report Post  
Old April 17th 08, 05:22 AM posted to rec.radio.shortwave
RHF RHF is offline
external usenet poster
 
First recorded activity by RadioBanter: Jun 2006
Posts: 8,652
Default Minimum gauge for groud...

On Apr 16, 6:12*pm, Telamon
wrote:
In article ,





*"Michael" wrote:
"dxAce" wrote in message
...


Michael wrote:


"Drakefan" wrote in message
news:nbZMj.6329$eg2.2049@trndny06...
Michael wrote:
Hiya...


Been a while since I posted here. *For the sake of noise
suppression as affective lightning protection is almost
hopeless without gas tubes, what would be the minimum gauge
wire that you could use for a ground from the radio to a ground
spike and from a matching transformer to a ground spike ??? *
Yes, I know there is loads of info on the net, but I would like
some active opinions as some recent discussions I have had on
this has been conflicting.


Also... I've gotten conflicting opinions on this one too. *If
you have a long wire or beverage set up on a matching
transformer like the ICE 180, there is a ground receptacle on
the matching transformer. *Would you:


A. *Use a separate ground wire from the matching transformer to
the ground spike and another separate ground wire from the
receiver to the ground spike ???


or


B. *Use one single ground wire from the receiver's ground port
going up to the matching transformer and then to the ground
spike ???


I know this stuff is antenna-101, but I'm interested to see
what the opinions here are


Thanx in advance !!!


Mike D. Northern NJ
First, the balun shouldn't be up in the air. It should be close
to the ground at the lower end of the vertical downlead wire of
the inverted-L antenna. Then you can use a short, less than
three feet, length of grounding wire from the balun to the rod.
The ground wire should be at least 10-gauge, preferably larger,
like 6 or 4-gauge. The coax should run on or in the ground to
the house and then to the radio. This will prevent it from
picking up noise on the coax shield, which can happen when the
coax is up in the air. It's not absolutely necessary to ground
the coax shield again near the radio if you follow the above
advice.


Thank you for all the replies. *My evil plan is this. *Since I
cant get the matching transformer away from the house, I will
secure it to the house's brick chimney. *The chimney goes all the
way to the concrete foundation and should make an excellent
ground.


Please explain why you think a 'brick chimney' will make an
excellent ground.


How about, the best thing approximating ground that is available on
my roof ???


- Get a dead chicken from the market, put it in a paper bag,
- stand up on your roof swinging the dead chicken in the bag
- around in a circle above your head and chant RHF, RHF over
and over until your reception improves.
-
- If that does not work try shouting Billy boy while doing the same.
-
- --
- Telamon
- Ventura, California
-

Teli - Hey - You do have an 'imagination' after all. ) ~ RHF
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Minimum gauge for groud... Dave[_15_] Shortwave 2 April 16th 08 03:33 PM
Minimum gauge for groud... Telamon Shortwave 2 April 16th 08 09:25 AM
Minimum gauge for groud... msg Shortwave 0 April 15th 08 03:16 PM
Minimum gauge for groud... Burr Shortwave 0 April 15th 08 05:37 AM
28 Gauge MnMikew Shortwave 0 February 17th 06 03:44 PM


All times are GMT +1. The time now is 08:28 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017