Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Old November 9th 04, 09:50 PM
DesignGuy
 
Posts: n/a
Default Home Intercom systems - possible source of RFI

For several years there have been annoying carriers on the SW bands at my
location - one of which was parked on top of WWV 10MHz. I recently decided
to track down some various RFI noise and discovered that my home intercom
system was the culprit. The one I have includes an AM/FM receiver and I
think it's the FM section putting out a carrier on or about 10MHz.

Hope this helps someone with similar troubles.



  #2   Report Post  
Old November 10th 04, 12:28 AM
Michael Black
 
Posts: n/a
Default


"DesignGuy" ) writes:
For several years there have been annoying carriers on the SW bands at my
location - one of which was parked on top of WWV 10MHz. I recently decided
to track down some various RFI noise and discovered that my home intercom
system was the culprit. The one I have includes an AM/FM receiver and I
think it's the FM section putting out a carrier on or about 10MHz.

Hope this helps someone with similar troubles.



How are the intercom stations connected? There's the obvious wire, but
at lest some use signals in the hundreds of KHz range. The signal is
impressed on the house wiring, and while much of the signal will be limited
to the AC line, obviously some of the weak signal can radiate.

Michael


  #3   Report Post  
Old November 10th 04, 12:31 AM
DesignGuy
 
Posts: n/a
Default


"Michael Black" wrote in message
...

"DesignGuy" ) writes:
For several years there have been annoying carriers on the SW bands at

my
location - one of which was parked on top of WWV 10MHz. I recently

decided
to track down some various RFI noise and discovered that my home

intercom
system was the culprit. The one I have includes an AM/FM receiver and I
think it's the FM section putting out a carrier on or about 10MHz.

Hope this helps someone with similar troubles.



How are the intercom stations connected? There's the obvious wire, but
at lest some use signals in the hundreds of KHz range. The signal is
impressed on the house wiring, and while much of the signal will be

limited
to the AC line, obviously some of the weak signal can radiate.



Sorry, forgot to mention this is a *wired* intercom, built in the walls of
the house. Not like the kind that plug in a run over the AC lines.




  #4   Report Post  
Old November 11th 04, 02:15 AM
0ff_Ramp
 
Posts: n/a
Default

I would scrap the wired intercom and get one of those new 5.8GHz cordless
phone systems with multiple handsets. With some of those new sets you can
page individual handsets from any other handset or a system wide intercom
page. I use the AT&T 5840 base with 4 additional 5800 handsets and it works
like a charm.


Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
FCC: Broadband Power Line Systems Paul Policy 0 January 10th 05 05:41 PM
Tx Source Impedance & Load Reflections Richard Fry Antenna 8 May 28th 04 06:29 PM
BPL - Comments on the original Inquiry document AK General 0 February 8th 04 02:18 AM
stuff for all hams [email protected] General 0 December 19th 03 07:31 PM
RF amps: tuned load in Class A? Don Pearce Homebrew 141 September 15th 03 05:02 AM


All times are GMT +1. The time now is 08:30 AM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017