LinkBack Thread Tools Search this Thread Display Modes
Prev Previous Post   Next Post Next
  #2   Report Post  
Old September 15th 06, 10:59 PM posted to rec.radio.amateur.antenna
external usenet poster
 
First recorded activity by RadioBanter: Jul 2006
Posts: 2,951
Default 12v regulator?

On Fri, 15 Sep 2006 21:34:55 GMT, ml wrote:

hi

kinda recently i stumbled onto a web site or article (ad) from someone
that was making a 12v regulator that took 12v from batteries to supply
your rig w/a more stable voltage

I lost that link and can't seem to find it or google it


Hi Myles,

That may be a blessing in disguise. A linear regulator will always
exhibit a lower voltage out than the voltage in. If you have 12V in,
you cannot have 12V out. It would have to be less. An expensive one
might offer a drop of tenths of a volt (11.6V to 11.9V out from 12.0V
in), but this depends on the current draw. Most Ham equipment is not
rated at 12V, but rather at 13.6V which is the potential of fully
charged batteries (2.25V per cell). The "12V regulator" you were
considering could easily drop the difference (1.6V) in an effort to
maintain a constant 12V. This is not a boon to maximizing output
power if that is your goal.

A switcher style regulator can be more efficient, but it will cost
much more too. Switchers can take a considerable range of input
voltages and supply a fairly consistent voltage at many loads. There
are switchers that can supply MORE voltage than what is applied to
their inputs, but at a cost of demanding MORE current from that
source. Think of switchers as a see-saw that exhibit a constant of
proportionality in power (less some loss). For instance, if you
needed 12V @ 20A, your switcher could convert it from 6V @ 40A, or it
could convert it from 24V @ 5A. [Actually, no one switcher design
could accommodate such a wide range with equal efficiency, but there
are designs tailored to either situation.]

However, if you demand too much current from your source, then no
regulator is going to supply it and regulation is going to fail.

Often, the best use of regulation is to keep circuits from going
haywire if the voltage droops excessively during transmission.
Unfortunately, during transmission, this is a condition of maximum
current demand. Basically, if your voltage droops too much, the
battery is either shot (bad cell) or under capacity. Get a new
battery, or get a battery with more A/H capacity. This alone could
make up the need for "regulation."

73's
Richard Clark, KB7QHC
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
R-390A: feeding oscillator tube heaters in DC, w/o regulator tube? SpamHog Boatanchors 4 April 22nd 06 01:06 PM
'Radio Spares' High Power Voltage Regulator spec ? Highland Ham Homebrew 1 February 13th 06 07:17 PM
WTD--Source for LM325H or SG2501 dual voltage regulator IC Bob Weiss Homebrew 3 June 8th 05 02:56 AM
Voltage Regulator Question Lou Boatanchors 0 April 3rd 04 06:49 PM
FS: GE MASTR II 10-Volt Regulator Card LJ Swap 0 March 7th 04 09:34 PM


All times are GMT +1. The time now is 07:04 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017