On May 28, 8:24 am, Buck wrote:


In view of your logic, let me tell you about my situation recently
when I tested a piece of coax on which I installed on connector.

There were already two connectors on the coax and I removed one that
was crimped and had slipped. I put on my connector and tested it with
my radio, no signal. Hmm, I needed to check the wire.

1) I tested the center conductor and the shield on the connector I
just installed... Short. OOPS!

I cut off the connector and replaced it.

2) Tested the center conductor and shield on the connector I just
installed... Short. OOPS again.

3) after cutting off my connector again, I tested the other connector.
between the coax and shield. Open. Great!

I soldered on the connector for the third time.
4) tested the center lead and shield of my connector... SHORT! Hmmmm

5) I cut off my connector and tested again. Open ?????

I tested the other connector again. Open.

ahhhh. I tested the center conductor from end to end.... OPEN!!!

I tested the center conductor to the shield on the end where I was
installing my connector.... SHORT!!!!

Time for a new piece of coax....

Sounds like too much heat.. You may be melting the clear jacket
and shorting the pin to shield. Be careful using too much heat when
soldering the shield. Sounds like you have a manly soldering gun..
MK

wrote:
Sounds like you have a manly soldering
gun..
MK


Or an underpowered one which produces
too great an area under the temp vs.
time curve.

An old-fashioned iron with a high
thermal mass tip is less likely to
damage the coax.

Chuck

----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----

On Mon, 28 May 2007 15:56:10 -0400, Chuck
wrote:

wrote:
Sounds like you have a manly soldering
gun..
MK


Or an underpowered one which produces
too great an area under the temp vs.
time curve.

An old-fashioned iron with a high
thermal mass tip is less likely to
damage the coax.

Chuck

----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----


Inside the coax near the other connector, the wire had broken and one
of the broken ends shorted the coax, the other broken end touched
nothing. I had to look long and hard. It was apparently just a
defect. It also happened to be the only accessible piece of coax
handy at the time. As stated above, I was just thinking I was
shorting out the coax connector, but when I cut it loose and it wasn't
shorted, i knew it had to be at the other end. However, the other end
appeared to be non-shorted. It wasn't till I took time to test the
length of center conductor that I discovered the open.


--
73 for now
Buck, N4PGW

www.lumpuckeroo.com

"Small - broadband - efficient: pick any two."

On 28-May-2007, wrote:

On May 28, 8:24 am, Buck wrote:


In view of your logic, let me tell you about my situation recently
when I tested a piece of coax on which I installed on connector.

There were already two connectors on the coax and I removed one that
was crimped and had slipped. I put on my connector and tested it with
my radio, no signal. Hmm, I needed to check the wire.

1) I tested the center conductor and the shield on the connector I
just installed... Short. OOPS!

I cut off the connector and replaced it.

2) Tested the center conductor and shield on the connector I just
installed... Short. OOPS again.

3) after cutting off my connector again, I tested the other connector.
between the coax and shield. Open. Great!

I soldered on the connector for the third time.
4) tested the center lead and shield of my connector... SHORT! Hmmmm

5) I cut off my connector and tested again. Open ?????

I tested the other connector again. Open.

ahhhh. I tested the center conductor from end to end.... OPEN!!!

I tested the center conductor to the shield on the end where I was
installing my connector.... SHORT!!!!

Time for a new piece of coax....

Sounds like too much heat.. You may be melting the clear jacket
and shorting the pin to shield. Be careful using too much heat when
soldering the shield. Sounds like you have a manly soldering gun..
MK

Sounds to me like the connector he didn't replace had an open center pin and a shorted braid.
Remember to make both short and open checks at both ends.

Ken

"Ken Fowler" wrote in message
. ..

On 28-May-2007, wrote:

On May 28, 8:24 am, Buck wrote:


In view of your logic, let me tell you about my situation recently
when I tested a piece of coax on which I installed on connector.

There were already two connectors on the coax and I removed one that
was crimped and had slipped. I put on my connector and tested it with
my radio, no signal. Hmm, I needed to check the wire.

1) I tested the center conductor and the shield on the connector I
just installed... Short. OOPS!

I cut off the connector and replaced it.

2) Tested the center conductor and shield on the connector I just
installed... Short. OOPS again.

3) after cutting off my connector again, I tested the other connector.
between the coax and shield. Open. Great!

I soldered on the connector for the third time.
4) tested the center lead and shield of my connector... SHORT! Hmmmm

5) I cut off my connector and tested again. Open ?????

I tested the other connector again. Open.

ahhhh. I tested the center conductor from end to end.... OPEN!!!

I tested the center conductor to the shield on the end where I was
installing my connector.... SHORT!!!!

Time for a new piece of coax....

Sounds like too much heat.. You may be melting the clear jacket
and shorting the pin to shield. Be careful using too much heat when
soldering the shield. Sounds like you have a manly soldering gun..
MK

Sounds to me like the connector he didn't replace had an open center pin
and a shorted braid.
Remember to make both short and open checks at both ends.

Ken

A meter that will read capacitance can be real handy. The end that has the
lowest capacitance is the OPEN end.