On Sep 13, 6:35*pm, wrote:
On Sep 13, 5:21*am, Chuck Forsberg WA7KGX N2469R
wrote:

The B version has a piece of mast below the main part of the
antenna. *Is there much difference in performance between
the arx2b and the original arx2?

--
Chuck Forsberg * *www.omen.com*503-614-0430
Developer of Industrial ZMODEM(Tm) for Embedded Applications
* Omen Technology Inc * * *"The High Reliability Software"
10255 NW Old Cornelius Pass Portland OR 97231 * FAX 629-0665

There is no extra mast. You are using the support mast
below the feed point. The extra parts are a 50 inch length
of coax, and a union to support a set of 20 inch long radials.
The radials are connected to the shield of the coax.
Years ago I converted an original Ringo Ranger to a
Ringo Ranger two using home brew parts.
I then did comparison tests with and without the radial
set. Made a huge difference in performance in my case.
Cushcraft seemed to consider it a third 5/8 WL element,
but I tend to consider it a decoupling section much
like the lower cone you see on an Isopole, or using
a 2nd set of radials or cones below a ground plane.
Yes, it is worth converting. The ARX2B is a pretty good
antenna. Not quite as good as the Isopole, but close.

I have seen people swear by and swear at Ringo Rangers. Is this
because of by chance some people get the right/wrong length mast and/
or coax length?

Jimmie

On Sep 13, 9:05*pm, JIMMIE wrote:
On Sep 13, 6:35*pm, wrote:



On Sep 13, 5:21*am, Chuck Forsberg WA7KGX N2469R
wrote:

The B version has a piece of mast below the main part of the
antenna. *Is there much difference in performance between
the arx2b and the original arx2?

--
Chuck Forsberg * *www.omen.com*503-614-0430
Developer of Industrial ZMODEM(Tm) for Embedded Applications
* Omen Technology Inc * * *"The High Reliability Software"
10255 NW Old Cornelius Pass Portland OR 97231 * FAX 629-0665

There is no extra mast. You are using the support mast
below the feed point. The extra parts are a 50 inch length
of coax, and a union to support a set of 20 inch long radials.
The radials are connected to the shield of the coax.
Years ago I converted an original Ringo Ranger to a
Ringo Ranger two using home brew parts.
I then did comparison tests with and without the radial
set. Made a huge difference in performance in my case.
Cushcraft seemed to consider it a third 5/8 WL element,
but I tend to consider it a decoupling section much
like the lower cone you see on an Isopole, or using
a 2nd set of radials or cones below a ground plane.
Yes, it is worth converting. The ARX2B is a pretty good
antenna. Not quite as good as the Isopole, but close.

I have seen people swear by and swear at Ringo Rangers. Is this
because of by chance some people get the right/wrong length mast and/
or coax length?

Jimmie

That could be the case with the non decoupled version. :/
But the RR2 is a pretty good antenna. I used one for a long
time and never had any problems.
The mast and coax length could be fairly critical on the
non decoupled version.
Like I said, I converted an old ARX2 to a ARX2B and then
compared the two when receiving local signals.
The difference in my particular case was quite large.
I'm talking 2-3+ S units on the radio meter which
actually would be a huge difference. It was quite
apparent that the common mode currents were really
whacking the pattern on the one I tried without the
decoupling section. I assume most was from the feed line.

On Mon, 14 Sep 2009 03:53:48 -0700, nm5k wrote:

On Sep 13, 9:05Â*pm, JIMMIE wrote:
On Sep 13, 6:35Â*pm, wrote:



On Sep 13, 5:21Â*am, Chuck Forsberg WA7KGX N2469R
wrote:

The B version has a piece of mast below the main part of the
antenna. Â*Is there much difference in performance between the arx2b
and the original arx2?

--
Chuck Forsberg Â* Â*www.omen.comÂ*503-614-0430
Developer of Industrial ZMODEM(Tm) for Embedded Applications
Â* Omen Technology Inc Â* Â* Â*"The High Reliability Software"
10255 NW Old Cornelius Pass Portland OR 97231 Â* FAX 629-0665

There is no extra mast. You are using the support mast below the feed
point. The extra parts are a 50 inch length of coax, and a union to
support a set of 20 inch long radials. The radials are connected to
the shield of the coax. Years ago I converted an original Ringo
Ranger to a Ringo Ranger two using home brew parts. I then did
comparison tests with and without the radial set. Made a huge
difference in performance in my case. Cushcraft seemed to consider it
a third 5/8 WL element, but I tend to consider it a decoupling
section much like the lower cone you see on an Isopole, or using a
2nd set of radials or cones below a ground plane. Yes, it is worth
converting. The ARX2B is a pretty good antenna. Not quite as good as
the Isopole, but close.

I have seen people swear by and swear at Ringo Rangers. Is this because
of by chance some people get the right/wrong length mast and/ or coax
length?

Jimmie

That could be the case with the non decoupled version. :/ But the RR2 is
a pretty good antenna. I used one for a long time and never had any
problems.
The mast and coax length could be fairly critical on the non decoupled
version.
Like I said, I converted an old ARX2 to a ARX2B and then compared the
two when receiving local signals. The difference in my particular case
was quite large. I'm talking 2-3+ S units on the radio meter which
actually would be a huge difference. It was quite apparent that the
common mode currents were really whacking the pattern on the one I tried
without the decoupling section. I assume most was from the feed line.


what is the easiest/cheapest way to add the decoupling?
Just add some 1/4 wavelength radials 1/2 wavelength below
the arx2?



--
Chuck Forsberg www.omen.com 503-614-0430
Developer of Industrial ZMODEM(Tm) for Embedded Applications
Omen Technology Inc "The High Reliability Software"
10255 NW Old Cornelius Pass Portland OR 97231 FAX 629-0665

On Sep 14, 5:52*pm, Chuck Forsberg WA7KGX N2469R
wrote:


what is the easiest/cheapest way to add the decoupling?
Just add some 1/4 wavelength radials 1/2 wavelength below
the arx2?

The factory version uses some kind of donut thing with
threaded holes for the radials. In my case, I just rigged
up a L plate of sorts that I drilled a hole for a coax union.
I used stiff wire radials that I bent into a short L at the end
and clamped them to the mast at that same plate.
The plate and radials naturally are grounded to the support
mast. You run a 50 inch length of coax from the feed point
down to the union on the radial/union plate. Adjust the
clamp so it's fairly taut. The radials are 20 inches long.
Not much to it. The trickiest part is making a union plate
and clamping it to the mast. Just use your imagination.
Not really critical as long as it's stays in place and grounds
to the mast. You can buy the threaded coax unions at
most of the radio parts stores. Maybe even rat shack.