Gentlemen,
I installed a 140 ft wire in hopes to match it on all HF bands. It
plays nicely through my ATU. I would like to modify this setup by
using about 20 ft.of coax inside the house (for a better look). Is
there a known matching scheme to accomodate the wire to the coax? What
other problems might I encounter?
Thanks for any help
73
wb6iiq
Fred

can you put an antenna analyzer on it?
If you can estimate the dominant impedance, you would have a better idea of
how to match it up.
I would be tempted to wind a 4-to-one balun on a toroid and put it at the
end of the coax to feed the wire - but I would be guessing.

"Fred" wrote in message
om...
Gentlemen,
I installed a 140 ft wire in hopes to match it on all HF bands. It
plays nicely through my ATU. I would like to modify this setup by
using about 20 ft.of coax inside the house (for a better look). Is
there a known matching scheme to accomodate the wire to the coax? What
other problems might I encounter?
Thanks for any help
73
wb6iiq
Fred


---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.732 / Virus Database: 486 - Release Date: 7/29/2004

On 16 Aug 2004 15:55:10 -0700, (Fred) wrote:

Gentlemen,
I installed a 140 ft wire in hopes to match it on all HF bands. It
plays nicely through my ATU. I would like to modify this setup by
using about 20 ft.of coax inside the house (for a better look). Is
there a known matching scheme to accomodate the wire to the coax? What
other problems might I encounter?
Thanks for any help
73
wb6iiq
Fred

I'm using roughly 140 feet of end-fed wire. Coax runs from the shack
out to underneath the near end of the wire, where I have a 4:1 balun.
One side of the balun goes to the wire, the other side goes to a ground
rod. TS-940S, IC-746PRO, and IC-703 all manage to match it on all HF
bands with no trouble. Coax length is not critical, but the balun
seems to help quite a bit.

--
-fb-

Gentlemen,
I installed a 140 ft wire in hopes to match it on all HF bands. It
plays nicely through my ATU. I would like to modify this setup by
using about 20 ft.of coax inside the house (for a better look). Is
there a known matching scheme to accomodate the wire to the coax? What
other problems might I encounter?
=================================

The known matching scheme is a tuner at the coax/antenna wire junction. For
multi-band operation a balun is fairly useless.

But if you don't fancy walking 20 feet to re-tune every time you change
frequency, reading the SWR meter with a telescope, why not do what I do. I
just extend the antenna wire into the house using plastic insulated 18 gauge
wire or something similar.

On the 160 and 80 meter bands you will notice no difference in performance
or behaviour. Just a difference in tuner settings. On the 15 and 10 meter
bands there might be an increase in RF inside the house over what you
usually get. You always get SOME RF in the shack/house with end-fed
antennas.

For an endfed wire you need a good ground near to the end of the antenna.
When the end of the antenna is in the house the domestic plumbing system
makes a very good ground. The hot and cold metal water pipes, with pipes to
central heating radiators in each room, constitute an excellent set of long
and thick "radials". It would be a great pity not to make use of them.
Make 1, 2 or perhaps 3 connections from the transmitter to different nearest
water pipes. Unobtrusive 18-gauge bare wire under carpets is fine. The
transmitter will also pick up an RF ground via the 110V or 230V power
wiring.
----
Reg, G4FGQ

Of course, if you have an automatic ATU you have no problems. Just locate it
at the junction of the end-fed antenna wire and the coax and merrily away
you go.
---
Reg.