"kenwood" wrote in message
...

****ty lesons for ya


"Mark" wrote in message
news:1106603212.83672@ftpsrv1...
Hi,

I have a Uniden Grant running as a base station, with a Leson power desk
mic
connected.

I heard a station loud and clear just now, and I keyed the desk mike to
reply. Probably only transmitted for about two seconds, long enough to
say
"Hello there, loud station".

But now the reception volume is incredibly low. Either on the internal
speaker or with an external speaker connected. You need to turn the
volume
pretty much flat out and then can only just make out the audio.

I discovered that my young daughter had wound up the knob on the Leson
desk
mic to about three-quarters the way round. I usually have it on about
one
notch out of ten, something like that.

I suspect that I've fried something inside with such a large power
setting
on the desk mic. Is this feasible? Have I literally overloaded the
transmitter by having the desk mic power so high? And why would that
cause
a
problem with the receiver audio output?

Thanks for any ideas!

Mark.





Hey, theres an improvement. He's (it) has found the caps lock key or is it
just a mellow mood ??

--
Regards ..... Rheilly Phoull

go and GET ****ED U TROLL
"Rheilly Phoull" wrote in message
...

"kenwood" wrote in message
...

****ty lesons for ya


"Mark" wrote in message
news:1106603212.83672@ftpsrv1...
Hi,

I have a Uniden Grant running as a base station, with a Leson power
desk
mic
connected.

I heard a station loud and clear just now, and I keyed the desk mike to
reply. Probably only transmitted for about two seconds, long enough to
say
"Hello there, loud station".

But now the reception volume is incredibly low. Either on the internal
speaker or with an external speaker connected. You need to turn the
volume
pretty much flat out and then can only just make out the audio.

I discovered that my young daughter had wound up the knob on the Leson
desk
mic to about three-quarters the way round. I usually have it on about
one
notch out of ten, something like that.

I suspect that I've fried something inside with such a large power
setting
on the desk mic. Is this feasible? Have I literally overloaded the
transmitter by having the desk mic power so high? And why would that
cause
a
problem with the receiver audio output?

Thanks for any ideas!

Mark.





Hey, theres an improvement. He's (it) has found the caps lock key or is it
just a mellow mood ??

--
Regards ..... Rheilly Phoull

kenwood wrote:

go and GET ****ED U TROLL

Remember, any response you give a troll, feeds a troll.

--
Paul Johnson

http://ursine.dyndns.org/~baloo/

"Rheilly Phoull" wrote in message
...

"kenwood" wrote in message
...

****ty lesons for ya


"Mark" wrote in message
news:1106603212.83672@ftpsrv1...
Hi,

I have a Uniden Grant running as a base station, with a Leson power
desk
mic
connected.

I heard a station loud and clear just now, and I keyed the desk mike
to
reply. Probably only transmitted for about two seconds, long enough to
say
"Hello there, loud station".

But now the reception volume is incredibly low. Either on the internal
speaker or with an external speaker connected. You need to turn the
volume
pretty much flat out and then can only just make out the audio.

I discovered that my young daughter had wound up the knob on the Leson
desk
mic to about three-quarters the way round. I usually have it on about
one
notch out of ten, something like that.

I suspect that I've fried something inside with such a large power
setting
on the desk mic. Is this feasible? Have I literally overloaded the
transmitter by having the desk mic power so high? And why would that
cause
a
problem with the receiver audio output?

Thanks for any ideas!

Mark.





Hey, theres an improvement. He's (it) has found the caps lock key or is it
just a mellow mood ??

--
Regards ..... Rheilly Phoull


G'day Rheilly, I think he just got confused with the postings from the
blokes below and thought he was giving them ,oops, Him, a bit back,
Clive Caviler (Alias Klutz)
Shane Shyster (Well no need to look up Shytser in the Dictionary)
Dave Dolt (Alias Dullard)
I could be wrong, some threads get bloody hard to follow at times,

Cheers, Warren