On Oct 24, 2:00*pm, "Paul Hovnanian P.E." wrote:
dgleeson422111 wrote:

Hello All

We have a propagation issue that is confusing us. We have two 868MHz
modules on test, each capable of 500mW transmission.

We are testing to find the range of communication. We are testing them
as follows. One remains in our office while the other is taken to the
street outside. we are communicating charecter strings such as "Im at
the lamp post number 1" etc. There is somebody at each end sending
text strings in a continuous conversation. There is no protocol, error
checking or error recovery.

What we have repetadly found is that the radio in the office can
receive long after the radio in the street has stopped receiving. (The
person with the radio in the street is moving away from the office.)

The radios are the same and the power supplies to the radios are the
same. Indeed switching the radios gives the same effect.

The propagation paths between the two radios are the same in terms of
distance. However the radio signal transmitted from the office travels
through walls first before then traveling through open space. Its the
opposite for the radio in the street, firstly traveling through space
and then through the walls in the office.

We did think we had identified an interfeering source in one direction
(when moving away from the office) so we started moving in the
opposite direction. We found exactly the same effect.

Are we getting interfeerance from GSM, ISM or Paging?

As far as GSM bands go in Europe 890-915 MHz OR 1710-1785 MHz So these
shouldnt be our problem.

ISM is where we intend to operate and the greatest band occupancy
should be 10%. So we should get communication even though we would get
some interfeerance.

Paging - well this has very much gone out of fashion in Europe. But
even if it was the cause then wouldnt it be intermittant
communication. We have a constant problem.

Can anyone shed light on this phenomonon? Is it an issue of wireless
propagation that Im not familiar with or is it Interfeerance?

Best regards, and thanks for any input.

Denis
_____________________
http://www.CentronSolutions.com

Have you tried relocating the office transceiver? There might be
something about the office environment that is interfering with its
transmission.

--
Paul Hovnanian * *
------------------------------------------------------------------
A mathematician is a machine for converting coffee into theorems.- Hide quoted text -

- Show quoted text -



wow so many of these replies are wrong..

in almost all cases, RF path losses are RECIPROCAL.

(even a 1/2 silvered mirror is reciprocal to light)

As some have said, the cause of your issue is probably interference to
the outside receiver.

Or maybe something about the indoor setup is causing the indoor Tx to
operate at lower power.

It is very unusual for RF path loss to be non-reciprocal.

Mark

Mark wrote:
On Oct 24, 2:00 pm, "Paul Hovnanian P.E." wrote:

wow so many of these replies are wrong..

This is normal when antenna "theory" comes up.

in almost all cases, RF path losses are RECIPROCAL.

I agree, including the antenna gains (meaning that the antennas at each end
don't have to match).

(even a 1/2 silvered mirror is reciprocal to light)

Well that guy is usually on a differet page.

As some have said, the cause of your issue is probably interference to
the outside receiver.

That's what I think is the most likely cause. The guy outside probably has
his Nextel phone with him. ;-)

Or maybe something about the indoor setup is causing the indoor Tx to
operate at lower power.

I suppose that's possible too. The OP should make sure the power supplies
are equivalent (meaning that the output power would suffer more than the
receiver gain with a drooping supply). So check the indoor supply.

It is very unusual for RF path loss to be non-reciprocal.

On Oct 24, 2:26*pm, "Anthony Fremont" wrote:
Mark wrote:
On Oct 24, 2:00 pm, "Paul Hovnanian P.E." wrote:
wow so many of these replies are wrong..

This is normal when antenna "theory" comes up.

in almost all cases, *RF path losses are RECIPROCAL.

I agree, including the antenna gains (meaning that the antennas at each end
don't have to match).

(even a 1/2 silvered mirror is reciprocal to light)

Well that guy is usually on a differet page.

As some have said, the cause of your issue is probably interference to
the outside receiver.

That's what I think is the most likely cause. *The guy outside probably has
his Nextel phone with him. *;-)

Or maybe something about the indoor setup is causing the indoor Tx to
operate at lower power.

I suppose that's possible too. *The OP should make sure the power supplies
are equivalent (meaning that the output power would suffer more than the
receiver gain with a drooping supply). *So check the indoor supply.



It is very unusual for RF path loss to be non-reciprocal.- Hide quoted text -

- Show quoted text -

It is assumed that the path to and from the office should be inferior
to the line of sight path out on the street. This may or may not be
true. The building may actually be offering gain in certain
directions. I would start by seeing if the same condition existed at
many more locations. If it does then other ideas need to be examined,
I would start by examining the RF environment outside the building.

Jimmie

Hello,

There should be a reciprocal relationship between the modules
regardless of height, antennas etc. as long as TX power and RX
sensitivity of the modules are the same (which they appear to be).

The modules are unlikely to have very good input filters at 868MHz, so
any adjacent channel interference (GSM etc.) is likely to cause the
out of balance behaviour.

Try heading in a different direction outside, or go somewhere else
with your experiment.

For your real world application, are you likely to have any site close
to adjacent channel transmitters (cell or broadcast) ? If so, think
about a decant front end filters. This could be costly, but might save
you...

Regards,

Mark



On Oct 25, 9:25*am, wrote:
On Oct 24, 2:26*pm, "Anthony Fremont" wrote:





Mark wrote:
On Oct 24, 2:00 pm, "Paul Hovnanian P.E." wrote:
wow so many of these replies are wrong..

This is normal when antenna "theory" comes up.

in almost all cases, *RF path losses are RECIPROCAL.

I agree, including the antenna gains (meaning that the antennas at each end
don't have to match).

(even a 1/2 silvered mirror is reciprocal to light)

Well that guy is usually on a differet page.

As some have said, the cause of your issue is probably interference to
the outside receiver.

That's what I think is the most likely cause. *The guy outside probably has
his Nextel phone with him. *;-)

Or maybe something about the indoor setup is causing the indoor Tx to
operate at lower power.

I suppose that's possible too. *The OP should make sure the power supplies
are equivalent (meaning that the output power would suffer more than the
receiver gain with a drooping supply). *So check the indoor supply.

It is very unusual for RF path loss to be non-reciprocal.- Hide quoted text -

- Show quoted text -

It is assumed that the path to and from the office should be inferior
to the line of sight path out on the street. This may or may not be
true. The building may actually be offering gain in certain
directions. I would start by seeing if the same condition existed at
many more locations. If it does then other ideas need to be examined,
I would start by examining the RF environment outside the building.

Jimmie- Hide quoted text -

- Show quoted text -

"Mark" wrote in message news:89e3cfad-c877-4be6-8eca-
wow so many of these replies are wrong..

in almost all cases, RF path losses are RECIPROCAL.

( It is very unusual for RF path loss to be non-reciprocal.

Mark


I agree. But, one thing that should be proven is that both modules
are working as intended. The one being used for the remote
application *could* be defective. Swap modules and see if the
receiving problem also switches locations, or remains the
same.

Pete

Tio Pedro wrote:

I agree. But, one thing that should be proven is that both modules
are working as intended. The one being used for the remote
application *could* be defective. Swap modules and see if the
receiving problem also switches locations, or remains the
same.

The OP said that he did that, and the problem remained. It's certainly a
desensing problem due to local interference at one end. That's the only
possible cause.

On Fri, 24 Oct 2008 02:14:24 -0700 (PDT), dgleeson422111
wrote:

Hello All

We have a propagation issue that is confusing us. We have two 868MHz
modules on test, each capable of 500mW transmission.

Hi Denis,

That is a lot of power for a problem of losing contact in the space of
blocks.

What we have repetadly found is that the radio in the office can
receive long after the radio in the street has stopped receiving. (The
person with the radio in the street is moving away from the office.)

The radios are the same and the power supplies to the radios are the
same. Indeed switching the radios gives the same effect.

The propagation paths between the two radios are the same in terms of
distance. However the radio signal transmitted from the office travels
through walls first before then traveling through open space. Its the
opposite for the radio in the street, firstly traveling through space
and then through the walls in the office.

A very good description of the symptoms and relations.

We did think we had identified an interfeering source in one direction
(when moving away from the office) so we started moving in the
opposite direction. We found exactly the same effect.

A good test for reducing variables. If you identified an
interference, I would presume you could do that again in the other
direction.

Are we getting interfeerance from GSM, ISM or Paging?

Only if the remote set was nearer to an undiscovered interferer. You
seemed to have resolved that once, and you should be able to detect
the similar occurrence again.

As far as GSM bands go in Europe 890–915 MHz OR 1710–1785 MHz So these
shouldnt be our problem.

This is a flaw in the logic. Your frequency of operation is very
close to these bands - unless your sets have been designed with
elaborate front end tuning (which seems unlikely).

Can anyone shed light on this phenomonon? Is it an issue of wireless
propagation that Im not familiar with or is it Interfeerance?

One component not discussed is the remote set's proximity to the
operator. The operator could disturb the local field (aka shield).
Going beyond is the effect of a Fresnel Zone, but your descriptions
describe a complete black-out. To test this requires you to go
further away to see if you pick up the signal again. This is a long
shot, however, as the effect would be distinct within the space of a
meter or so. For mobile operation, the Fresnel Zone creates what is
called "Picket Fencing" as the signal comes and goes quickly with
distance traveled.

Perhaps it is the proximity of a Pub, and your operator stopped in for
a Guinness.

73's
Richard Clark, KB7QHC

dgleeson422111 wrote:
Hello All

We have a propagation issue that is confusing us. We have two 868MHz
modules on test, each capable of 500mW transmission.

We are testing to find the range of communication. We are testing them
as follows. One remains in our office while the other is taken to the
street outside. we are communicating charecter strings such as "Im at
the lamp post number 1" etc. There is somebody at each end sending
text strings in a continuous conversation. There is no protocol, error
checking or error recovery.

What we have repetadly found is that the radio in the office can
receive long after the radio in the street has stopped receiving. (The
person with the radio in the street is moving away from the office.)

The radios are the same and the power supplies to the radios are the
same. Indeed switching the radios gives the same effect.

The propagation paths between the two radios are the same in terms of
distance. However the radio signal transmitted from the office travels
through walls first before then traveling through open space. Its the
opposite for the radio in the street, firstly traveling through space
and then through the walls in the office.

We did think we had identified an interfeering source in one direction
(when moving away from the office) so we started moving in the
opposite direction. We found exactly the same effect.

Are we getting interfeerance from GSM, ISM or Paging?

As far as GSM bands go in Europe 890–915 MHz OR 1710–1785 MHz So these
shouldnt be our problem.

ISM is where we intend to operate and the greatest band occupancy
should be 10%. So we should get communication even though we would get
some interfeerance.

Paging - well this has very much gone out of fashion in Europe. But
even if it was the cause then wouldnt it be intermittant
communication. We have a constant problem.

Can anyone shed light on this phenomonon? Is it an issue of wireless
propagation that Im not familiar with or is it Interfeerance?

Best regards, and thanks for any input.


I'll second Pere and Anthony. Strong out-of-band signals is what I found
mostly in situations where path losses seemed strangely non-reciprocal.

Post a schematic. One possibility is that your receive input filter is
wide open like a barn door and GSM swamps the receiver.

Another option if you have a spectrum analyzer: Hang a large near-field
probe into a long cable, tape it to a broomstick and hold that out the
window for a while. See what pops up on the screen. If this is in a city
be prepared for some commotion among the pedestrians down there :-)

--
Regards, Joerg

http://www.analogconsultants.com/

"gmail" domain blocked because of excessive spam.
Use another domain or send PM.

Hey:

My crystal balls are saying:

Multipath where a reflected signal from the source
is being cancelled out in the zone sort of like
standing waves. It's like waves in a bath tub
they bounce of the sides and produce more inter-
ference waves, and so on. Or FM broadcast stations
signal in the big city with tall buildings, all of a sudden
the signal just goes puff while you're driving along down-
town.

I'd say gits your antenna near a window or put up an
outdoor antenna.

73 OM

n8zu

"dgleeson422111" wrote in message
...
Hello All

We have a propagation issue that is confusing us. We have two 868MHz
modules on test, each capable of 500mW transmission.

We are testing to find the range of communication. We are testing them
as follows. One remains in our office while the other is taken to the
street outside. we are communicating charecter strings such as "Im at
the lamp post number 1" etc. There is somebody at each end sending
text strings in a continuous conversation. There is no protocol, error
checking or error recovery.

What we have repetadly found is that the radio in the office can
receive long after the radio in the street has stopped receiving. (The
person with the radio in the street is moving away from the office.)

The radios are the same and the power supplies to the radios are the
same. Indeed switching the radios gives the same effect.

The propagation paths between the two radios are the same in terms of
distance. However the radio signal transmitted from the office travels
through walls first before then traveling through open space. Its the
opposite for the radio in the street, firstly traveling through space
and then through the walls in the office.

We did think we had identified an interfeering source in one direction
(when moving away from the office) so we started moving in the
opposite direction. We found exactly the same effect.

Are we getting interfeerance from GSM, ISM or Paging?

As far as GSM bands go in Europe 890–915 MHz OR 1710–1785 MHz So these
shouldnt be our problem.

ISM is where we intend to operate and the greatest band occupancy
should be 10%. So we should get communication even though we would get
some interfeerance.

Paging - well this has very much gone out of fashion in Europe. But
even if it was the cause then wouldnt it be intermittant
communication. We have a constant problem.

Can anyone shed light on this phenomonon? Is it an issue of wireless
propagation that Im not familiar with or is it Interfeerance?

Best regards, and thanks for any input.

Denis
_____________________
http://www.CentronSolutions.com

its interesting that a commercial company would bring a problem such as this
to a bunch of amateur radio operators... true some of the amateurs may be
professional engineers, but the remainder are not! I guess that in today's
market place we try to gain information on the dirt and cheap way.