|
On Thu, 6 Nov 2003 21:45:47 -0800, Dr. Anton Squeegee
wrote: In article , uk- says... HI THERE Just a thought , I have often made my own alum boxes , for projects that I have built myself , and have always wanted to solder the edges shut , for a more pleasing look , or sometimes solder two pieces together. snip Won't happen. Or at least no one that I know of, in 20+ years of hamateur activity, has ever managed to do it. The only way I know of to seamlessly join pieces of aluminum, as you describe, is by welding them. To do so, my understanding is that you need special equipment and an inert gas environment. Indeed. The TIG welding process is ideal for this, particularly if a professional finish is important. But the kit *is* expensive and there's a bit of a skill to be picked up (not *that* difficult, though). -- Q: Why does Mike Tyson cry during sex? A: It's the pepper spray. |
On Thu, 6 Nov 2003 19:06:33 -0000, "uk-hamman"
wrote: HI THERE Just a thought , I have often made my own alum boxes , for projects that I have built myself , and have always wanted to solder the edges shut , for a more pleasing look , or sometimes solder two pieces together. I've never succeeded with soldering Ali, what I do is the use aluminium filings loaded into epoxy resin as a glue/filler. My method is to. Degrease the aluminium with Carbon Tet. or similar. Stick some tape over the joint to be 'closed' on the side you can't easily file, leaving a gap / fillet for the epoxy to fill. Mix the epoxy as per normal then introduce the fileings. I find diecast ali fileings are best as they seem to be more granular and file finer grit. 'wet' the joint with some unloaded epoxy and then fill the joint with the loaded epoxy using a spatula. After its set I file the joint to an acceptable profile. I have used this method to fill unwanted holes in diecast boxes with good results. I'm not sure about its screening ability but its a lot better than an open hole, both for screening and presentation. The best epoxy I have used is called "JB Weld" which is incredible for sticking ali and it is easily worked. Acceptable results are possible with "Araldite" but it does'nt appear to have the same 'stick' ability. hth, Mike W, G8NXD |
On Thu, 6 Nov 2003 19:06:33 -0000, "uk-hamman"
wrote: HI THERE Just a thought , I have often made my own alum boxes , for projects that I have built myself , and have always wanted to solder the edges shut , for a more pleasing look , or sometimes solder two pieces together. I've never succeeded with soldering Ali, what I do is the use aluminium filings loaded into epoxy resin as a glue/filler. My method is to. Degrease the aluminium with Carbon Tet. or similar. Stick some tape over the joint to be 'closed' on the side you can't easily file, leaving a gap / fillet for the epoxy to fill. Mix the epoxy as per normal then introduce the fileings. I find diecast ali fileings are best as they seem to be more granular and file finer grit. 'wet' the joint with some unloaded epoxy and then fill the joint with the loaded epoxy using a spatula. After its set I file the joint to an acceptable profile. I have used this method to fill unwanted holes in diecast boxes with good results. I'm not sure about its screening ability but its a lot better than an open hole, both for screening and presentation. The best epoxy I have used is called "JB Weld" which is incredible for sticking ali and it is easily worked. Acceptable results are possible with "Araldite" but it does'nt appear to have the same 'stick' ability. hth, Mike W, G8NXD |
There is an epoxy out there is made for joining aluminum( I forget the name,
its like JB-Weld, but for aluminum). You can find it at the larger auto parts stores, and you should be able to find it on the internet. When you grind/file it down, it's hard to tell where the aluminum ends and the epoxy begins. Jim "Mike W" wrote in message ... On Thu, 6 Nov 2003 19:06:33 -0000, "uk-hamman" wrote: HI THERE Just a thought , I have often made my own alum boxes , for projects that I have built myself , and have always wanted to solder the edges shut , for a more pleasing look , or sometimes solder two pieces together. I've never succeeded with soldering Ali, what I do is the use aluminium filings loaded into epoxy resin as a glue/filler. My method is to. Degrease the aluminium with Carbon Tet. or similar. Stick some tape over the joint to be 'closed' on the side you can't easily file, leaving a gap / fillet for the epoxy to fill. Mix the epoxy as per normal then introduce the fileings. I find diecast ali fileings are best as they seem to be more granular and file finer grit. 'wet' the joint with some unloaded epoxy and then fill the joint with the loaded epoxy using a spatula. After its set I file the joint to an acceptable profile. I have used this method to fill unwanted holes in diecast boxes with good results. I'm not sure about its screening ability but its a lot better than an open hole, both for screening and presentation. The best epoxy I have used is called "JB Weld" which is incredible for sticking ali and it is easily worked. Acceptable results are possible with "Araldite" but it does'nt appear to have the same 'stick' ability. hth, Mike W, G8NXD --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.536 / Virus Database: 331 - Release Date: 11/3/03 |
There is an epoxy out there is made for joining aluminum( I forget the name,
its like JB-Weld, but for aluminum). You can find it at the larger auto parts stores, and you should be able to find it on the internet. When you grind/file it down, it's hard to tell where the aluminum ends and the epoxy begins. Jim "Mike W" wrote in message ... On Thu, 6 Nov 2003 19:06:33 -0000, "uk-hamman" wrote: HI THERE Just a thought , I have often made my own alum boxes , for projects that I have built myself , and have always wanted to solder the edges shut , for a more pleasing look , or sometimes solder two pieces together. I've never succeeded with soldering Ali, what I do is the use aluminium filings loaded into epoxy resin as a glue/filler. My method is to. Degrease the aluminium with Carbon Tet. or similar. Stick some tape over the joint to be 'closed' on the side you can't easily file, leaving a gap / fillet for the epoxy to fill. Mix the epoxy as per normal then introduce the fileings. I find diecast ali fileings are best as they seem to be more granular and file finer grit. 'wet' the joint with some unloaded epoxy and then fill the joint with the loaded epoxy using a spatula. After its set I file the joint to an acceptable profile. I have used this method to fill unwanted holes in diecast boxes with good results. I'm not sure about its screening ability but its a lot better than an open hole, both for screening and presentation. The best epoxy I have used is called "JB Weld" which is incredible for sticking ali and it is easily worked. Acceptable results are possible with "Araldite" but it does'nt appear to have the same 'stick' ability. hth, Mike W, G8NXD --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.536 / Virus Database: 331 - Release Date: 11/3/03 |
On Fri, 07 Nov 2003 20:54:15 GMT, "kf4tun"
wrote: There is an epoxy out there is made for joining aluminum( I forget the name, its like JB-Weld, but for aluminum). You can find it at the larger auto parts stores, and you should be able to find it on the internet. When you grind/file it down, it's hard to tell where the aluminum ends and the epoxy begins. Jim ============================ I've noticed from this thread that all of the materials that successfully allow aluminum soldering seem to have one major disadvantage. Loss of memory. Jack |
On Fri, 07 Nov 2003 20:54:15 GMT, "kf4tun"
wrote: There is an epoxy out there is made for joining aluminum( I forget the name, its like JB-Weld, but for aluminum). You can find it at the larger auto parts stores, and you should be able to find it on the internet. When you grind/file it down, it's hard to tell where the aluminum ends and the epoxy begins. Jim ============================ I've noticed from this thread that all of the materials that successfully allow aluminum soldering seem to have one major disadvantage. Loss of memory. Jack |
"J. Yazel" wrote in message ... On Fri, 07 Nov 2003 20:54:15 GMT, "kf4tun" wrote: There is an epoxy out there is made for joining aluminum( I forget the name, its like JB-Weld, but for aluminum). You can find it at the larger auto parts stores, and you should be able to find it on the internet. When you grind/file it down, it's hard to tell where the aluminum ends and the epoxy begins. Jim ============================ I've noticed from this thread that all of the materials that successfully allow aluminum soldering seem to have one major disadvantage. Loss of memory. Jack What can I say? I forgot what we were talking about! Jim --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.537 / Virus Database: 332 - Release Date: 11/6/03 |
"J. Yazel" wrote in message ... On Fri, 07 Nov 2003 20:54:15 GMT, "kf4tun" wrote: There is an epoxy out there is made for joining aluminum( I forget the name, its like JB-Weld, but for aluminum). You can find it at the larger auto parts stores, and you should be able to find it on the internet. When you grind/file it down, it's hard to tell where the aluminum ends and the epoxy begins. Jim ============================ I've noticed from this thread that all of the materials that successfully allow aluminum soldering seem to have one major disadvantage. Loss of memory. Jack What can I say? I forgot what we were talking about! Jim --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.537 / Virus Database: 332 - Release Date: 11/6/03 |
Try this...
Get some good motor oil and put a drop on the aluminum... Then scrape the aluminum oxide off under the oil... ....[snip].... I've done the very same thing except using silver-cleaning paste! Although it's a bother, it DOES work. I've also seen the demonstrations of the things sold at hamfests, it appears to work very well, and the cost was not bad, either. --Myron. -- Five boxes preserve our freedoms: soap, ballot, witness, jury, and cartridge PhD EE (retired). "Barbershop" tenor. CDL(PTX). W0PBV. (785) 539-4448 NRA Life Member and Certified Instructor (Home Firearm Safety, Rifle, Pistol) |
| All times are GMT +1. The time now is 11:55 PM. |
Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
RadioBanter.com