In article ,
(William) writes:

(Brian Kelly) wrote in message
.com...
PAMNO (N2EY) wrote in message news:
...

All it took for a ham to stay inside the subbands was a frequency
standard of
known accuracy. This could take the form of an accurately-calibrated
receiver,
transmitter or transceiver, an external frequency meter (WW2 surplus
BC-221 and
LM units were relatively inexpensive in the 1960s) or a 100 kHz
oscillator with
suitable dividers.

He's clueless. As usual. I could comfortably transmit CW within 200Hz
of any band edge or subband edge with my Collins 75A4 and know I was
"legal". I simply tweaked the 100Khz xtal oscillator to get it dead
on against WWV on several freqs and took it from there. The
out-of-the-box Collins PTO and linear dial with it's adjustable cursor
*is* a frequency meter and it's far more accurate than any of W2
surplus units. Not to mention being much more convenient to use.

Straight out of the 1950s ham catalogs bub . . all of it.

All of it?

So I guess all the hoopla about constructing one's own station to be a
real ham was just a bunch of smoke going up someones hamstring?

Not even a Heathkit in there anywhere?

Sheesh!

Heathkits are for "drudges."

Those who sit at captain's tables (natuarlly) had Collins... :-)

(Len Over 21) wrote in message ...
In article ,
(William) writes:

(Brian Kelly) wrote in message
.com...
PAMNO (N2EY) wrote in message news:
...

All it took for a ham to stay inside the subbands was a frequency
standard of
known accuracy. This could take the form of an accurately-calibrated
receiver,
transmitter or transceiver, an external frequency meter (WW2 surplus
BC-221 and
LM units were relatively inexpensive in the 1960s) or a 100 kHz
oscillator with
suitable dividers.

He's clueless. As usual. I could comfortably transmit CW within 200Hz
of any band edge or subband edge with my Collins 75A4 and know I was
"legal". I simply tweaked the 100Khz xtal oscillator to get it dead
on against WWV on several freqs and took it from there. The
out-of-the-box Collins PTO and linear dial with it's adjustable cursor
*is* a frequency meter and it's far more accurate than any of W2
surplus units. Not to mention being much more convenient to use.

Straight out of the 1950s ham catalogs bub . . all of it.

All of it?

So I guess all the hoopla about constructing one's own station to be a
real ham was just a bunch of smoke going up someones hamstring?

Not even a Heathkit in there anywhere?

Sheesh!

Heathkits are for "drudges."

Those who sit at captain's tables (natuarlly) had Collins... :-)



Yep, 35 years later they've got Collins. Keepin' up with the times.

William wrote:

Yep, 35 years later they've got Collins. Keepin' up with the times.

That's right, "William", I've got a modified 75A-3 which is about 51
years old, a 51S-1 which was produced in the late seventies and a
KWM-2A which was built about the same time as Len's Icom R-70 receiver.
I have an Orion which was produced last year.

I also have other functional ham gear from the twenties, thirties,
forties, fifties, sixties, seventies, eighties and nineties. I'm
keeping up with the times--ALL of 'em.

Dave K8MN

Dave Heil wrote in message ...
William wrote:

Yep, 35 years later they've got Collins. Keepin' up with the times.

That's right, "William", I've got a modified 75A-3 which is about 51
years old, a 51S-1 which was produced in the late seventies and a
KWM-2A which was built about the same time as Len's Icom R-70 receiver.
I have an Orion which was produced last year.

How do you like using the Orion?

I stopped by Ten-Tec last year and looked at it, didn't buy it.

I also have other functional ham gear from the twenties, thirties,
forties, fifties, sixties, seventies, eighties and nineties. I'm
keeping up with the times--ALL of 'em.

Dave K8MN

Nothing earlier?

William wrote:

Dave Heil wrote in message ...
William wrote:

Yep, 35 years later they've got Collins. Keepin' up with the times.

That's right, "William", I've got a modified 75A-3 which is about 51
years old, a 51S-1 which was produced in the late seventies and a
KWM-2A which was built about the same time as Len's Icom R-70 receiver.
I have an Orion which was produced last year.

How do you like using the Orion?

No rig is perfect. The Orion is very, very close.

I stopped by Ten-Tec last year and looked at it, didn't buy it.

They still make 'em.

I also have other functional ham gear from the twenties, thirties,
forties, fifties, sixties, seventies, eighties and nineties. I'm
keeping up with the times--ALL of 'em.

Nothing earlier?

To have anything earlier, I'd have to find something earlier. All I
have is a piece of something earlier. My late friend W4JBP first became
a ham in 1912 on the family farm near Indianapolis. John gave me the
spark coil from an old Reo truck. It was the basis for his very first
rig. It is coated in pitch and mounted in a small dovetailed wooden
box.

Dave K8MN

Dave Heil wrote in message ...
William wrote:

Dave Heil wrote in message ...
William wrote:

Yep, 35 years later they've got Collins. Keepin' up with the times.

That's right, "William", I've got a modified 75A-3 which is about 51
years old, a 51S-1 which was produced in the late seventies and a
KWM-2A which was built about the same time as Len's Icom R-70 receiver.
I have an Orion which was produced last year.

How do you like using the Orion?

No rig is perfect. The Orion is very, very close.

I stopped by Ten-Tec last year and looked at it, didn't buy it.

They still make 'em.

I know. And the last QST had a nice ad for it. To be honest, I don't
know what I want in my next rig. That's why I keep looking.

I also have other functional ham gear from the twenties, thirties,
forties, fifties, sixties, seventies, eighties and nineties. I'm
keeping up with the times--ALL of 'em.

Nothing earlier?

To have anything earlier, I'd have to find something earlier.

I've only seen photos.

All I
have is a piece of something earlier. My late friend W4JBP first became
a ham in 1912 on the family farm near Indianapolis. John gave me the
spark coil from an old Reo truck. It was the basis for his very first
rig. It is coated in pitch and mounted in a small dovetailed wooden
box.

Dave K8MN

If you build it, you'll be tempted to use it.

William wrote:

Dave Heil wrote in message ...
William wrote:

Dave Heil wrote in message ...
William wrote:

Yep, 35 years later they've got Collins. Keepin' up with the times.

That's right, "William", I've got a modified 75A-3 which is about 51
years old, a 51S-1 which was produced in the late seventies and a
KWM-2A which was built about the same time as Len's Icom R-70 receiver.
I have an Orion which was produced last year.

How do you like using the Orion?

No rig is perfect. The Orion is very, very close.

I stopped by Ten-Tec last year and looked at it, didn't buy it.

They still make 'em.

I know. And the last QST had a nice ad for it. To be honest, I don't
know what I want in my next rig. That's why I keep looking.

I also have other functional ham gear from the twenties, thirties,
forties, fifties, sixties, seventies, eighties and nineties. I'm
keeping up with the times--ALL of 'em.

Nothing earlier?

To have anything earlier, I'd have to find something earlier.

I've only seen photos.

All I
have is a piece of something earlier. My late friend W4JBP first became
a ham in 1912 on the family farm near Indianapolis. John gave me the
spark coil from an old Reo truck. It was the basis for his very first
rig. It is coated in pitch and mounted in a small dovetailed wooden
box.

If you build it, you'll be tempted to use it.

You vastly underestimate my self-restraint. Using a spark rig is
something to which I aspire. I have a couple of TNT self-controlled
type replica transmitters. If the antenna swung in the breeze, they'd
be all over the band. I've resisted the temptation to put them on the
air for about a decade.

Dave K8MN

Dave Heil wrote in message ...
William wrote:

Dave Heil wrote in message ...
William wrote:

Yep, 35 years later they've got Collins. Keepin' up with the times.

That's right, "William", I've got a modified 75A-3 which is about 51
years old, a 51S-1 which was produced in the late seventies and a
KWM-2A

NICE collection!

which was built about the same time as Len's Icom R-70 receiver.
I have an Orion which was produced last year.

How do you like using the Orion?

No rig is perfect. The Orion is very, very close.

I stopped by Ten-Tec last year and looked at it, didn't buy it.

They still make 'em.

But David they don't come with antennas and somebody who knows how to
install antennas so that's the end of Silly Willy Beeper's Ten-tec
dream machine.

I also have other functional ham gear from the twenties, thirties,
forties, fifties, sixties, seventies, eighties and nineties. I'm
keeping up with the times--ALL of 'em.

Nothing earlier?

To have anything earlier, I'd have to find something earlier. All I
have is a piece of something earlier. My late friend W4JBP first became
a ham in 1912 on the family farm near Indianapolis. John gave me the
spark coil from an old Reo truck. It was the basis for his very first
rig. It is coated in pitch and mounted in a small dovetailed wooden
box.

Yeeee-haw! One of those was my very first "transmitter"!

In seventh or eighth grade I found a big thick dusty 1920s compilation
of DIY projects which had appeared earlier in Popular Mechanics in the
jr. high library. What there was of it. 1950 timeframe. Lotta radio
projects and I built a couple crystal sets from the articles. None of
this 1N34 nonsense, go find a chunk of Galena then go find a hot spot
on it with a home-brewed cat whisker . . worked.

There was an article on building a spark TX based on a Model T Ford
spark coil which is obviously the same critter Reo used. I went spark
coil hunting and bought mine from J.C. Whitney which stocked heaps of
Model T parts and diddled with it. My Lionel train transformer did a
good job as it's "power supply".

I wrapped a dozen or so turns of wire around the wooden box to serve
as the "secondary" of the spark coil and grounded one end of it to a
copper water pipe in the rafters. Then I strung up some wire from the
"output" end of the secondary fom my cellar "laboratory" to an apple
tree out back. Connected a J-38 between the Lionel xfmr output and the
spark coil primary and was set to hit the airwaves.

I needed somebody to listen for me and after several days of getting
patted on my noggin and being written off as a nutcase I managed to
finally recruit George Barnum who lived a block and a half away to
listen for me. His older brother had a radio and TV repair shop so
George sorta understood what I was up to. He heard me *good* when I
fired the thing up on sked.

The problem was that I really screwed up by arranging the sked when
every houswife in town was listening to the Don McNeil Breakfast Club
Hour while they were doing their ironing. I completely obliterated the
AM b'cast band for blocks around, the phone rang off the hook and Mom
not only terminated my Grand Experiment but almost terminated me too.
Again.

.. . . growing up is such a bitch . .

Dave K8MN

w3rv

(Brian Kelly) wrote in message . com...
Dave Heil wrote in message ...
William wrote:

Dave Heil wrote in message ...
William wrote:

Yep, 35 years later they've got Collins. Keepin' up with the times.

That's right, "William", I've got a modified 75A-3 which is about 51
years old, a 51S-1 which was produced in the late seventies and a
KWM-2A

NICE collection!

which was built about the same time as Len's Icom R-70 receiver.
I have an Orion which was produced last year.

How do you like using the Orion?

No rig is perfect. The Orion is very, very close.

I stopped by Ten-Tec last year and looked at it, didn't buy it.

They still make 'em.

But David they don't come with antennas and somebody who knows how to
install antennas so that's the end of Silly Willy Beeper's Ten-tec
dream machine.

Kelly, I never have had an HF radio that came with an antenna.
Perhaps your do. Yet I managed to build my own cubical quad on HF,
dipoles, off-center fed dipoles, and EDZ's for 10 and 6, a hustler
vertical for 40, etc, etc, etc.

But in this particular location, I have very precise requirements and
your one size fits all suggestion just wasn't what I wanted. Thank
you for your suggestion, but don't force it on me. Reminds me of the
time you told me to bend over. Thanks, but No thanks. Some kind of
weird elmering going on where you're from.

I also have other functional ham gear from the twenties, thirties,
forties, fifties, sixties, seventies, eighties and nineties. I'm
keeping up with the times--ALL of 'em.

Nothing earlier?

To have anything earlier, I'd have to find something earlier. All I
have is a piece of something earlier. My late friend W4JBP first became
a ham in 1912 on the family farm near Indianapolis. John gave me the
spark coil from an old Reo truck. It was the basis for his very first
rig. It is coated in pitch and mounted in a small dovetailed wooden
box.

Yeeee-haw! One of those was my very first "transmitter"!

In seventh or eighth grade I found a big thick dusty 1920s compilation
of DIY projects which had appeared earlier in Popular Mechanics in the
jr. high library. What there was of it. 1950 timeframe. Lotta radio
projects and I built a couple crystal sets from the articles. None of
this 1N34 nonsense, go find a chunk of Galena then go find a hot spot
on it with a home-brewed cat whisker . . worked.

There was an article on building a spark TX based on a Model T Ford
spark coil which is obviously the same critter Reo used. I went spark
coil hunting and bought mine from J.C. Whitney which stocked heaps of
Model T parts and diddled with it. My Lionel train transformer did a
good job as it's "power supply".

I wrapped a dozen or so turns of wire around the wooden box to serve
as the "secondary" of the spark coil and grounded one end of it to a
copper water pipe in the rafters. Then I strung up some wire from the
"output" end of the secondary fom my cellar "laboratory" to an apple
tree out back. Connected a J-38 between the Lionel xfmr output and the
spark coil primary and was set to hit the airwaves.

I needed somebody to listen for me and after several days of getting
patted on my noggin and being written off as a nutcase I managed to
finally recruit George Barnum who lived a block and a half away to
listen for me. His older brother had a radio and TV repair shop so
George sorta understood what I was up to. He heard me *good* when I
fired the thing up on sked.

What was you callsign then?

Or were you bootlegging as you've previously reported?

The problem was that I really screwed up by arranging the sked when
every houswife in town was listening to the Don McNeil Breakfast Club
Hour while they were doing their ironing.

Actually, you're biggest screwup was operating w/o a license.

I completely obliterated the
AM b'cast band for blocks around, the phone rang off the hook and Mom
not only terminated my Grand Experiment but almost terminated me too.
Again.

. . . growing up is such a bitch . .

Maybe that's why you've done so little of it over the years.

Dave K8MN

w3rv

bb

Brian Kelly wrote:

Dave Heil wrote in message ...
William wrote:

Dave Heil wrote in message ...
William wrote:

Yep, 35 years later they've got Collins. Keepin' up with the times.

That's right, "William", I've got a modified 75A-3 which is about 51
years old, a 51S-1 which was produced in the late seventies and a
KWM-2A

NICE collection!

....and I saw a fairly priced 75A-4 at the Washington, PA hamfest this
morning. I resisted.

which was built about the same time as Len's Icom R-70 receiver.
I have an Orion which was produced last year.

How do you like using the Orion?

No rig is perfect. The Orion is very, very close.

I stopped by Ten-Tec last year and looked at it, didn't buy it.

They still make 'em.

But David they don't come with antennas and somebody who knows how to
install antennas so that's the end of Silly Willy Beeper's Ten-tec
dream machine.

Ahhh! They have a "William" variant. The Orion is available with a
built-in antenna tuner. I didn't get that model.

I also have other functional ham gear from the twenties, thirties,
forties, fifties, sixties, seventies, eighties and nineties. I'm
keeping up with the times--ALL of 'em.

Nothing earlier?

To have anything earlier, I'd have to find something earlier. All I
have is a piece of something earlier. My late friend W4JBP first became
a ham in 1912 on the family farm near Indianapolis. John gave me the
spark coil from an old Reo truck. It was the basis for his very first
rig. It is coated in pitch and mounted in a small dovetailed wooden
box.

Yeeee-haw! One of those was my very first "transmitter"!

In seventh or eighth grade I found a big thick dusty 1920s compilation
of DIY projects which had appeared earlier in Popular Mechanics in the
jr. high library. What there was of it. 1950 timeframe. Lotta radio
projects and I built a couple crystal sets from the articles. None of
this 1N34 nonsense, go find a chunk of Galena then go find a hot spot
on it with a home-brewed cat whisker . . worked.

There was an article on building a spark TX based on a Model T Ford
spark coil which is obviously the same critter Reo used. I went spark
coil hunting and bought mine from J.C. Whitney which stocked heaps of
Model T parts and diddled with it. My Lionel train transformer did a
good job as it's "power supply".

I wrapped a dozen or so turns of wire around the wooden box to serve
as the "secondary" of the spark coil and grounded one end of it to a
copper water pipe in the rafters. Then I strung up some wire from the
"output" end of the secondary fom my cellar "laboratory" to an apple
tree out back. Connected a J-38 between the Lionel xfmr output and the
spark coil primary and was set to hit the airwaves.

I needed somebody to listen for me and after several days of getting
patted on my noggin and being written off as a nutcase I managed to
finally recruit George Barnum who lived a block and a half away to
listen for me. His older brother had a radio and TV repair shop so
George sorta understood what I was up to. He heard me *good* when I
fired the thing up on sked.

The problem was that I really screwed up by arranging the sked when
every houswife in town was listening to the Don McNeil Breakfast Club
Hour while they were doing their ironing. I completely obliterated the
AM b'cast band for blocks around, the phone rang off the hook and Mom
not only terminated my Grand Experiment but almost terminated me too.
Again.

You actually disrupted the march around the breakfast table? My pre-ham
radio days were from Hinton, West Virginia with an old doorbell buzzer
and ten-volt transformer. I "worked" Bobby Hayth next door. We were
each using old BC/SW receivers in wooden cabinets but we could have used
any AM receiver on about any frequency at that distance. Let's just say
that the tuning wasn't at all critical. Something about decrement, heh
heh.

Dave K8MN