LinkBack Thread Tools Search this Thread Display Modes
Prev Previous Post   Next Post Next
  #4   Report Post  
Old March 19th 11, 09:34 PM posted to rec.radio.shortwave
RHF RHF is offline
external usenet poster
 
First recorded activity by RadioBanter: Jun 2006
Posts: 8,652
Default New (to me) radio...and NOISE.

On Mar 19, 11:53*am, dave wrote:
On 3/19/2011 7:11 AM, RHF wrote:



That should do some good; and usually the more
you use the more effective they collectively become.


If you can/have access to both ends of the Wires :
{ Place a Ferrite Bead [FB] on Each End of Each Wire}
Solar Panel [FB] =Wires-to= [FB] Outback
Outback [FB] =Wires-to= [FB] Batteries
Outback [FB] =Wires-to= [FB House


The chokes should go as close to the noise source as possible. They do
zero good at the other end.


Dave -with-all-due-respect-

Unless {Specifically} You Know The RFI Noise Source :
Every Thing Is The Potential [Unknown] Source :
Therefore Treat Every Thing As The Source

Install FBs on Unit "A" -now- Unit "A" with a FB's
on the Wire within an Inch or two from it is Protected.
Those FBs acting as an RFI Shunts for Unit "A".

However [But] the 25 Feet of Wire(s) going from Unit "A"
to Unit "B" are a 'potential' Antenna. This Antenna may
Pick-Up the RFI being Radiated from Unit "A" an inject
the RFI back into Unit "B" and now Unit "B" passes that
Noise around the rest of the System.

Now install FBs on Unit "B" -now- Unit "B" with a FB's
on the Wire within an Inch or two from it is Protected.
Those FBs acting as an RFI Shunts for Unit "B".

Oops there is also a 25 Feet of Wire(s) going from Unit
"B" to Unit "C" are a 'potential' Antenna.

the process of elimination continues ~ RHF

I have small slide-on FB's on all the Wires on the Solar
Array of now 88 Panels : The Contractors said it was not
necessary & I Said Do It.

I have Clamp-On FBs at the Service Feed Box at the
base of the Solar Array.

I have Clamp-On FBs at the Service Entry Box at the
Controller / Regulators / Inverters.

I have Clamp-On FBs at the Enclosure for the Batteries
about 3-Inches from each Battery.

Except for the 200KW Generator at the Corner of the Pond
going 'On' and the snap-crackle-pop of a string of Power Grid
Towers about a 1/4 Mile Away {Lions Dam to the Valley}
I get an S-Meter "0" on many bands between RF Signals.
and I Run 100 Foot+ SWL Antennas.

I Am One Old Believer In "FB"s Everywhere : Especially
When Wire Runs Get Longer than 6~8 Feet- iane ~ RHF
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Radio noise amdx Homebrew 8 February 14th 04 01:20 AM
Radio noise amdx Homebrew 0 February 13th 04 01:41 AM
WTB: HP/Agilent 346A (or B) Noise Source for HP 8970A Noise Figure Meter Carl R. Stevenson Homebrew 0 January 21st 04 04:20 AM
Automatic RF noise cancellation and audio noise measurement JGBOYLES Antenna 25 August 11th 03 01:07 AM
Automatic RF noise cancellation and audio noise measurement Dave Shrader Homebrew 35 August 11th 03 01:07 AM


All times are GMT +1. The time now is 03:03 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017