S R wrote:

I want to build an antenna for my shortwave radio. I live in an apartment.
So it would have to be something I could put near the window. No longer
then 3 feet.

My idea is having 2 wires in a coil. Wrapped around PVC tubing on each end.
It would look like the letter T. ( I am not sure which size of tubing to
use).

I am not sure how many feet of wire.

Which type of wire.

Should the wire be shield or not shield.

If not shield, then when I wrap the wire, can it touch itself in the turn or
must it be spaced apart?

Then comes the end of the two wires. What do I use to solder to then plug
into my portable radio?

And is their a way I could make a tuner and have the wires connected to that
first then to the radio?

Thanks.

73

Before you start building indoor antennas, try putting at least 10-ft of
fine wire (#30 enameled magnet wire) out through a second story window
or higher. You can put a small weight like a washer on the end to make
the wire hang down the side of the building (not really necessary) but
make sure the weight doesn't hit any window below. No one is likely to
see this 'invisible' antenna wire unless they're looking for it. Connect
the other end of the wire to the whip antenna on your portable. Be sure
to remove some of the enameled insulation (using sand paper) to expose
the bare copper wire where it connects to the whip.


-----= Posted via Newsfeeds.Com, Uncensored Usenet News =-----
http://www.newsfeeds.com - The #1 Newsgroup Service in the World!
-----== Over 100,000 Newsgroups - 19 Different Servers! =-----

starman wrote:


Before you start building indoor antennas, try putting at least 10-ft of
fine wire (#30 enameled magnet wire) out through a second story window
or higher. You can put a small weight like a washer on the end to make
the wire hang down the side of the building (not really necessary) but
make sure the weight doesn't hit any window below. No one is likely to
see this 'invisible' antenna wire unless they're looking for it. Connect
the other end of the wire to the whip antenna on your portable. Be sure
to remove some of the enameled insulation (using sand paper) to expose
the bare copper wire where it connects to the whip.


-----= Posted via Newsfeeds.Com, Uncensored Usenet News =-----
http://www.newsfeeds.com - The #1 Newsgroup Service in the World!
-----== Over 100,000 Newsgroups - 19 Different Servers! =-----

I have found that I get better results wrapping the insulated wire
around the whip of my receiver (only in about a 2-3 turn coil) than
attaching it directly with an alligator clip, it seems to me there is
less noise this way. Another thing, I grounded the wire to a copper
pipe where it comes into the house. I don't know if this does anything,
but I read somewhere that this was advisable so it removes static
electricity that can build up in the wire.

I want to build a out-door antenna.

Your idea is great, but where could I find that type of wire?

I am sure Radio Shack doesn't carry it. All of there wires are shield.

73


"starman" wrote in message
...
S R wrote:

I want to build an antenna for my shortwave radio. I live in an
apartment.
So it would have to be something I could put near the window. No
longer
then 3 feet.

My idea is having 2 wires in a coil. Wrapped around PVC tubing on each
end.
It would look like the letter T. ( I am not sure which size of tubing
to
use).

I am not sure how many feet of wire.

Which type of wire.

Should the wire be shield or not shield.

If not shield, then when I wrap the wire, can it touch itself in the
turn or
must it be spaced apart?

Then comes the end of the two wires. What do I use to solder to then
plug
into my portable radio?

And is their a way I could make a tuner and have the wires connected to
that
first then to the radio?

Thanks.

73

Before you start building indoor antennas, try putting at least 10-ft of
fine wire (#30 enameled magnet wire) out through a second story window
or higher. You can put a small weight like a washer on the end to make
the wire hang down the side of the building (not really necessary) but
make sure the weight doesn't hit any window below. No one is likely to
see this 'invisible' antenna wire unless they're looking for it. Connect
the other end of the wire to the whip antenna on your portable. Be sure
to remove some of the enameled insulation (using sand paper) to expose
the bare copper wire where it connects to the whip.


-----= Posted via Newsfeeds.Com, Uncensored Usenet News =-----
http://www.newsfeeds.com - The #1 Newsgroup Service in the World!
-----== Over 100,000 Newsgroups - 19 Different Servers! =-----

In article ,
says...
I want to build a out-door antenna.

Your idea is great, but where could I find that type of wire?

I am sure Radio Shack doesn't carry it. All of there wires are shield.

Radio Shack does carry magnet wire, though they're far from the cheapest
source. Much of the wire they sell is insulated, very little of it is
shielded. There's a big difference. Regular insulated wire will work
fine. Magnet wire is often suggested because it's cheap and very
stealthy. As long as no one trips over it, it's unlikely they'll ever
notice it.