LinkBack Thread Tools Search this Thread Display Modes
Prev Previous Post   Next Post Next
  #18   Report Post  
Old May 20th 04, 11:39 AM
RHF
 
Posts: n/a
Default

= = = "Brian" wrote in message
= = = thlink.net...

Anyone know if the variable cap, that I'm assuming is included
in this kit, will suffice for the bc band loop I want to build ?

http://www.radioshack.com/product.asp?catalog%5Fname=CTLG&product%5Fid=28-179

Brian

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

BRIAN,

Since this is an AM & FM Radio 'Kit' it most likely uses a
"Miniature Poly-film Variable Tuning Capacitor" for AM & FM Bands
CAPS= http://www.oselectronics.com/ose_p98.htm
Part Number: BC-88

Ideal Variable Tuning Capacitor for miniature circuitry and use
as exact-duplicate replacement in current transistor receivers.
Tunes AM Band from 540Khz to 1600Khz and FM band from 88Mhz to
108Mhz. Rotates through a full 180°

Maximum Capacity:
AM/MW Antenna Section AM 21-152PF, Oscillator Section AM, 10-74PF.
FM Antenna Section FM 23-44PF, Oscillator Section FM, 14-23PF

Trimmer Capacity: variable to over 12PF.
Trimmer adjustment on rear of case.

Completely enclosed to clear polyethylene
plastic case to protect plates.
Includes calibrated dial, screw, and knob.
Small size, 3/4" Square x 1/2" Deep.


BETTER ALTERNATIVE:
AM/MW "Only" Tuning Capacitor: (Good for AM/MW Loop Antennas)
For your Loop Antenna 'Project' you may wish to consider a Capacitor
that is specifically designed to work within the Band Range of the
AM/MW Broadcast band.

"Miniature 1 Gang Poly-Film Variable Tuning Capacitor For Broadcast Band"
CAPS= http://www.oselectronics.com/ose_p98.htm
Part Number: BC-280

Tunes AM band from 540 kHz to 1600 kHz. Ideal Variable Tuning
Capacitor for miniature circuitry and use as exact-duplicate
replacement in current transistor receivers.
Works great in crystal radio sets. (Loop Antennas)
- Rotates through a full 180°
- Maximum Capacity: Single section tunes from 10-280pf.
- Completely enclosed in a clear polyethylene
plastic case to protect plates.
- Includes Calibrated Dial, Screw, and Knob.
Small size, 3/4" Square x 1/2" Deep.

REQUIRES: Loop Antenna Inductance of about 350 uH
when using a Variable Capacitor Range of 10 to 280 pf.

"AM Loop Antenna Calculator" - by Bruce Carter (Version 4, 5-19-2003)
CAL= http://www.mindspring.com/~loop_ante...loop_calc4.htm

Check-Out the "Loop Antenna Information Forum" eGroup on YAHOO!
LOOPS= http://groups.yahoo.com/group/loopantennas/

jm2cw ~ RHF

..
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
FA:Heathkit Variable voltage bench power supply Clifton Turner Equipment 3 September 17th 04 04:16 AM
FA:Heathkit Variable voltage bench power supply Clifton Turner Equipment 0 September 13th 04 04:37 AM
FA:Heathkit Variable voltage bench power supply Clifton Turner Equipment 0 September 13th 04 04:37 AM
FS: old radio parts, coils, variable caps, toroids, Loral disk capassortment, GC-Stackpole resistor assortment Al Schapira Boatanchors 0 January 16th 04 05:33 PM
Variable stub Alfred Lorona Antenna 3 July 30th 03 12:37 AM


All times are GMT +1. The time now is 04:42 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017