Hi
I got the base out. An old ham buddy stopped by and we cranked and hammered
that end out. The bottom section of the X200a antenna that is connected to
the whip. The bottom half of the antenna out of that bottom piece of
fiberglass tube. Very green as there was water sitting in there. Ok so at
the base is a coil that is tapped at about 75% through it and that tapping
(there are two) one to the shield part of the S0239 and one to the center of
the S0239 connector. Both are broken and both look like there is a capacitor
there that split apart.

Any idea what those two caps are? I think if I just clean the element up
with sand paper, deoxit it and replace those caps (if that is what is there)
looks like two small caps were supposed to be there or what is there could
be corroded up broken caps.

Or is that little piece available online anywhere?

Or could I simply connect everything to the gnd planes or even lengthen
those gnd planes and connect short everything as I only want to use as
receive for the scanner. I am probably at about 3 or 4 hours cleaning this
old antenna up, compared to the costs of a new one.

Thanks for your thoughts

73s





"Wimpie" wrote in message
abel.net...
El 05-05-13 13:57, Tom escribió:
Thanks for the advice.

The 2m 70cm old antenna someone gave me is a Diamond X200 I believe.
It is about 2.4 meters long with a connection in the middle. It was
full of water and for many years, I took it apart yesterday and
emptied the water and green stuff out and sanded the entier top part
of the element and coils. I will de-oxit it and put it back together
and seal it better. I cannot get the bottom length of antenna out of
the fiberglass shell so I will leave that greenish but I noticed there
was continuity between the outside shield of the S0239 connector and
the antenna and not continuity between the center of the Coax
connector and the antenna. I thought the center coax would connect
with the antenna and the shield would connect with the gnd planes. Is
that normal?

From the center of the SO239 connector on the antenna there is no
continuity between anything. Only continuity between the threads of
the SO239 and the antenna length. After I put it all together I will
use the AV600 meter to tests its SWR with the 2m70cm rig to see if it
is ok.

That bottom fiberglass piece looks glued in there pretty good I don't
want to break the seal , I think the water might be getting in from
that half way connector.

Can this antenna be modified for broader band scanner use? Most of my
interests in the scanning will be the marine bands (156 ish megs) and
VHF and UHF ham bands anyway.

Thanks gents for the advice,,,

73s


Hello Tom,

I don't know the internal construction of your antenna, but when SWR turns
out to be good on 2m and 70cm, the antenna is very likely good and can be
used for reception, but on 2m and 70 cm only. As Jeff also said, these
antenna are narrow band and performance on VHF marine band will be well
below that of a simple halve wave dipole tuned for VHF marine. It does
not mean it receives nothing, but you only hear nearby stations on the
2m/70cm antenna when tuning your scanner to VHF air or VHF marine.

If you want one antenna that fits all, go for the discone, or even better,
go for the biconical antenna. I fully agree with Jeff, the biconical
dipole has better radiation pattern for your application.

When you enter biconical cebik into a search engine you may find useful
info on biconical antennas if you plan to construct your own antenna. As
your VHF and UHF bands of interest have around 3:1 ratio, VSWR will be
good enough for reception.

Wim
PA3DJS
don't forget to remove abc in case of PM





"Ralph Mowery" wrote in message
m...

"Tom" wrote in message
...
Hi

I have the Realistic Programmable scanner with 200 programable
channels. A lot of range there like 6 m, 2 m, 70 cm, marine, etc
etc etc, wide range.

I want to put up an external antenna that I can hook it up to its
own BNC connection for external antenna. I believe the higher the
better.

Which is better to run a bare copper wire longest and highest to
connect it to the BNC center? Or should I use coax and splice the
center copper feed to

You will not receive much with a long bare copper wire.

Get some coax, rg8x is good, the rg 6 type is also good and usually
cheap. Don't worry about the 70 ohm impedance of the rg-6 as the
impedance is not going to be 50 ohms anyway over much of the
frequecny range. The lmr400 type is beter, but I doubt that you will
notice the differance if the length is around 100 feet or less. Not
worth the big price differance for a scanner in many cases. The only
problem with the rg6 may be the connectors as the shield is usually
aluminum or a material that will not take solder. The crimp
connectors are fine.

For the outside antenna, a discone type is often used. Really for a
broad band reception any ground plane or colinear will probably give
you good reception over a wide band. After all, the short antenna
that usually comes with the scanners often pick up many signals.






--
Wim
PA3DJS
www.tetech.nl
Please remove abc first in case of PM