LinkBack Thread Tools Search this Thread Display Modes
Prev Previous Post   Next Post Next
  #11   Report Post  
Old April 22nd 06, 05:04 PM posted to rec.radio.shortwave,rec.radio.amateur.antenna
Irv Finkleman
 
Posts: n/a
Default question about tunable capacitor: how to mount ??

switcher wrote:

On the picture, you'll see 7 connections for the cables, oe at the
bottom (7), 6 at the top of the C. How do I need to connect the cables
to have the maximum out of my AM/SW loop antenna ??

http://users.fulladsl.be/spb13810/amloop/tunablec.jpg

I would like to know what I can do with screws A, B, C and D, and of
course, where to connect the cable ends ...

I am making one loop with these tools:
these are the picts:
http://users.fulladsl.be/spb13810/amloop/loop83cm.jpg

the loop, diameter = 83 cm.

http://users.fulladsl.be/spb13810/amloop/loopbottom.jpg
The bottom, a plastic case 11 x 18 cm.

http://users.fulladsl.be/spb13810/am...oopbottom2.jpg
The plastic screws that fit the hulahoop.

I will mount the C inside the box, so I'll have no cables outside ...

Thanks,
Marc

--
een appeltje te schillen met http://applefaulty.be
http://users.fulladsl.be/spb13810/bwnl.htm
Breng je iMac G5 terug (ik wil binnen 2 jaar geen defecte 2de hands Apple kopen)
http://www.apple.com/nl/support/imac...ensionprogram/


The capacitor device is very common in most portable radios. It has two sections
for AM tuning, and two for FM tuning. The 'screws' adjust trimmer capacitors which
are in parallel with the four main capacitors.

You do not specify what frequency you intend to tune the loop to. If you want it
for a band of frequencies what range to you plan to cover. I suggest that you
take some alligator clip leads and temporarily hook up the loop to one end of
each lead. Then try connecting the other ends to different terminals on the
capacitor and tune the cap through its range and listen for an increase in
noise at the receiver. You will have to tune very slowly as the high Q of
the loop will make the selectivity very sharp and you can miss the noise point
easily.

You would be much better off to get some ham to give you a small variable
from his junk box. It will work better and will be much easier
to mount in the case. With a one meter loop, a capacitor with a value of 100 pf
or less should beable to tune between about 7 and 30 mhz.

Irv VE6BP
--
--------------------------------------
Diagnosed Type II Diabetes March 5 2001
Beating it with diet and exercise!
297/215/210 (to be revised lower)
58"/43"(!)/44" (already lower too!)
--------------------------------------
Visit my HomePage at http://members.shaw.ca/finkirv/index.html
Visit my Baby Sofia website at http://members.shaw.ca/finkirv4/index.htm
Visit my OLDTIMERS website at http://members.shaw.ca/finkirv5/index.htm
--------------------
Irv Finkleman,
Grampa/Ex-Navy/Old Fart/Ham Radio VE6BP
Calgary, Alberta, Canada
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Pedestal Mount Question Mike General 0 February 16th 05 06:22 PM
Magnet Mount Ground Question [email protected] CB 7 January 24th 05 07:22 AM
BOLO STOLEN XTL5000 mobiles here are serials and models john private smith Swap 2 January 6th 04 05:01 AM
FS: Connectors/Adapters/Meters/Etc. Ben Equipment 0 January 1st 04 02:55 PM
Larson glass mount question Dan Antenna 6 November 14th 03 07:54 PM


All times are GMT +1. The time now is 06:15 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017