Jim,

Yes, I had a similar problem with one of my TS-830s rigs but to a lesser
degree. The problem would occur like yours, then the display would come on,
frequency would be irratic for another 20 minutes or so. This is the classic
Kenwood grounding problem cited in the QST review of the TS-830S and also
described by Rich Measures (AF6K?). Solution is to tighten all screws holding
PC boards to the frame and attaching a ground wire to the AF/AVR board (Rich
Measures website has step by step instructions). Not sure if this is related
to your problem or not.

73s,

Evan

On 01 Dec 2003 02:09:53 GMT, (K9SQG) wrote:

Jim,

Yes, I had a similar problem with one of my TS-830s rigs but to a lesser
degree. The problem would occur like yours, then the display would come on,
frequency would be irratic for another 20 minutes or so. This is the classic
Kenwood grounding problem cited in the QST review of the TS-830S and also
described by Rich Measures (AF6K?). Solution is to tighten all screws holding
PC boards to the frame and attaching a ground wire to the AF/AVR board (Rich
Measures website has step by step instructions). Not sure if this is related
to your problem or not.

73s,

Evan

Rich Measures call is AG6K. Quite a bit of information on his web
site concerning the TS-830s

"K9SQG" wrote in message
...
Jim,

Yes, I had a similar problem with one of my TS-830s rigs but to a lesser
degree. The problem would occur like yours, then the display would come
on,
frequency would be irratic for another 20 minutes or so. This is the
classic
Kenwood grounding problem cited in the QST review of the TS-830S and also
described by Rich Measures (AF6K?). Solution is to tighten all screws
holding
PC boards to the frame and attaching a ground wire to the AF/AVR board
(Rich
Measures website has step by step instructions). Not sure if this is
related
to your problem or not.

73s,

Evan

All good advice. Also remove those little plastic plugs on the boards.
Eyeball for corrosion or wetness. Clean as needed and spray with a good
quality contact cleaner.

Dan/W4NTI

"K9SQG" wrote in message
...
Jim,

Yes, I had a similar problem with one of my TS-830s rigs but to a lesser
degree. The problem would occur like yours, then the display would come
on,
frequency would be irratic for another 20 minutes or so. This is the
classic
Kenwood grounding problem cited in the QST review of the TS-830S and also
described by Rich Measures (AF6K?). Solution is to tighten all screws
holding
PC boards to the frame and attaching a ground wire to the AF/AVR board
(Rich
Measures website has step by step instructions). Not sure if this is
related
to your problem or not.

73s,

Evan

Also spray all the switches.

Dan/W4NTI

On 01 Dec 2003 02:09:53 GMT, (K9SQG) wrote:

Jim,

Yes, I had a similar problem with one of my TS-830s rigs but to a lesser
degree. The problem would occur like yours, then the display would come on,
frequency would be irratic for another 20 minutes or so. This is the classic
Kenwood grounding problem cited in the QST review of the TS-830S and also
described by Rich Measures (AF6K?). Solution is to tighten all screws holding
PC boards to the frame and attaching a ground wire to the AF/AVR board (Rich
Measures website has step by step instructions). Not sure if this is related
to your problem or not.

73s,

Evan

Rich Measures call is AG6K. Quite a bit of information on his web
site concerning the TS-830s

"K9SQG" wrote in message
...
Jim,

Yes, I had a similar problem with one of my TS-830s rigs but to a lesser
degree. The problem would occur like yours, then the display would come
on,
frequency would be irratic for another 20 minutes or so. This is the
classic
Kenwood grounding problem cited in the QST review of the TS-830S and also
described by Rich Measures (AF6K?). Solution is to tighten all screws
holding
PC boards to the frame and attaching a ground wire to the AF/AVR board
(Rich
Measures website has step by step instructions). Not sure if this is
related
to your problem or not.

73s,

Evan

All good advice. Also remove those little plastic plugs on the boards.
Eyeball for corrosion or wetness. Clean as needed and spray with a good
quality contact cleaner.

Dan/W4NTI

"K9SQG" wrote in message
...
Jim,

Yes, I had a similar problem with one of my TS-830s rigs but to a lesser
degree. The problem would occur like yours, then the display would come
on,
frequency would be irratic for another 20 minutes or so. This is the
classic
Kenwood grounding problem cited in the QST review of the TS-830S and also
described by Rich Measures (AF6K?). Solution is to tighten all screws
holding
PC boards to the frame and attaching a ground wire to the AF/AVR board
(Rich
Measures website has step by step instructions). Not sure if this is
related
to your problem or not.

73s,

Evan

Also spray all the switches.

Dan/W4NTI