You should be able to tune it in.
I have used my DX398 and have had no trouble.
Try tuning slowly above and below.
I am receiving the 6.925 pirate (now Underground radio)
in USB, so tune below it.

Terry

I don't quite know what you mean by "tune below it," but I wonder if
there's something wrong with my radio. It's always sounded like this in
SSB.

BTW, I'm in Fort Wayne, IN. Know where they're transmitting from?

It is not just a case of flipping a switch. I haven't had a 398 in several
years but the basics are, switch to sideband mode, set the tuning for lowest
posible tuning steps (40 hz in this radio) and use the tuning knob to tune
it in. If you can't get it tuned, you are in the wrong sideband. Switch to
the other and do it again. Likely, in this part of the spectrum, those
pirates are on lower sideband.
"Scott A." wrote in message
...
I don't quite know what you mean by "tune below it," but I wonder if
there's something wrong with my radio. It's always sounded like this in
SSB.

BTW, I'm in Fort Wayne, IN. Know where they're transmitting from?

In article .com,
wrote:

You should be able to tune it in. I have used my DX398 and have had
no trouble. Try tuning slowly above and below. I am receiving the
6.925 pirate (now Underground radio) in USB, so tune below it.

He is not complaining about picking the signal up but making it
understandable. You can't do this with DX-398. No SSB mode or BFO means
no SSB detection.

--
Telamon
Ventura, California

ER, you might want to take a look at the DX398 again.
I have mine in front of me and it certainly does have
SSB mode, support for both LSB and USB.
I modified mine to defeat the tuning muting, but
even with that, I just barrowed my wife's stock
DX398 and I can tune it just fine. I prefer the lack
of mute,.
On the lower right front there is a button labled
am/mode. This toggles/steps the radio through
AMLSBUSBAM.
Again, please recheck your "facts".
Terry

Check out:
http://support.radioshack.com/produc...20-228&Reuse=N
This should take you to the page at Tandy's web with a direct link
to a PDF of the owner's manual.
Terry

Check again. The 398 is fully ssb capable.

"Telamon" wrote in message
...
In article .com,
wrote:

You should be able to tune it in. I have used my DX398 and have had
no trouble. Try tuning slowly above and below. I am receiving the
6.925 pirate (now Underground radio) in USB, so tune below it.

He is not complaining about picking the signal up but making it
understandable. You can't do this with DX-398. No SSB mode or BFO means
no SSB detection.

--
Telamon
Ventura, California

In article ,
"CW" wrote:

Check again. The 398 is fully ssb capable.

"Telamon" wrote in message
..
.
In article .com,
wrote:

You should be able to tune it in. I have used my DX398 and have had
no trouble. Try tuning slowly above and below. I am receiving the
6.925 pirate (now Underground radio) in USB, so tune below it.

He is not complaining about picking the signal up but making it
understandable. You can't do this with DX-398. No SSB mode or BFO means
no SSB detection.

I did check again. I mixed up the model number. The 398 does have SSB
and the 380 I own does not. I read the post and then looked at my radio
and then commented on mine without noting the original post had a
different number. Dumb.

It was a bad model number day for me as I did a similar thing in another
post yesterday.

--
Telamon
Ventura, California

He is not complaining about picking the signal up but making it
understandable. You can't do this with DX-398. No SSB mode or BFO means
no SSB detection.

My 398 does it just fine. (????)

jt

From the DX-398 Manual at URL:


TUNING SSB STATIONS
Your receiver receives both USB and LSB transmissions. Follow these steps to
receive SSB stations.

The page (18) goes on to give a step by step tuning procedure

"making it understandable" is covered as follows (from the DX-398 Manual

Note: SSB stations sound distorted when you tune to them in the normal SW
band. To help you find SSB stations, watch for deflections on the signal
strength indicator. Since SSB is transmitted with a suppressed carrier, the
signal strength indicator will move more quickly when there is a
transmission and more slowly during pauses in the transmission.

When you have located an SSB station, press AM MODE to receive the
transmission. Repeatedly press AM MODE to switch between USB or LSB
transmissions (try LSB for frequencies below 10 MHz or USB for frequencies
above 10 MHz).

4. Set STEP to SLOW then readjust MANUAL TUNING slowly for maximum
intelligibility.

73
--
Caveat Lector



"Jmpngtiger" wrote in message
...
He is not complaining about picking the signal up but making it
understandable. You can't do this with DX-398. No SSB mode or BFO means
no SSB detection.

My 398 does it just fine. (????)

jt