Home |
Search |
Today's Posts |
|
#1
|
|||
|
|||
JB Weld Waterweld and/or Loctite repair epoxy for dipole insulators??
"Jayson" wrote in message ... I recently came across some JB Weld Waterweld and Loctite repair putty. I have used this two part hand moldable epoxy for various indoor projects and have met with success on a number of occasions. I am now preparing to erect a dipole and I am wondering how well this epoxy would work for the center/ end insulators? My main concerns are UV, weathering and of course longitudinal strength. Anyone have experiences/ recommendations they can share? Thank you. I thought that one of the parts had some powdered steel or something in it. Anyway....make a sample and test it in the microwave. |
#2
|
|||
|
|||
JB Weld Waterweld and/or Loctite repair epoxy for dipole insulators??
No, according to their website, standard JB Weld and Waterweld are
nonconductive. I have some hardened Waterweld here that I just tested with the ohmeter and there is no conductivity. They do have a steel reinforced one thought that would be conductive I suspect. Why would I want to test this stuff in the microwave? "Wayne" wrote in message ... "Jayson" wrote in message ... I recently came across some JB Weld Waterweld and Loctite repair putty. I have used this two part hand moldable epoxy for various indoor projects and have met with success on a number of occasions. I am now preparing to erect a dipole and I am wondering how well this epoxy would work for the center/ end insulators? My main concerns are UV, weathering and of course longitudinal strength. Anyone have experiences/ recommendations they can share? Thank you. I thought that one of the parts had some powdered steel or something in it. Anyway....make a sample and test it in the microwave. |
#3
|
|||
|
|||
JB Weld Waterweld and/or Loctite repair epoxy for dipole insulators??
On 11/23/2011 9:57 AM, Jayson wrote:
Why would I want to test this stuff in the microwave? Dielectric losses. Make sure you have a cup of water in there while you do it. But afterwards check the blob of material to make sure it stayed at room temperature. Jeff -- "Everything from Crackers to Coffins" |
#4
|
|||
|
|||
JB Weld Waterweld and/or Loctite repair epoxy for dipole insulators??
On Wed, 23 Nov 2011 18:21:05 -0600, Jeffrey Angus
wrote: On 11/23/2011 9:57 AM, Jayson wrote: Why would I want to test this stuff in the microwave? Dielectric losses. Make sure you have a cup of water in there while you do it. But afterwards check the blob of material to make sure it stayed at room temperature. Jeff -- Yeah...what Jeff said. :-) --Wayne W5GIE |
#5
|
|||
|
|||
JB Weld Waterweld and/or Loctite repair epoxy for dipole insulators??
On 11/23/2011 10:57 AM, Jayson wrote:
No, according to their website, standard JB Weld and Waterweld are nonconductive. I have some hardened Waterweld here that I just tested with the ohmeter and there is no conductivity. They do have a steel reinforced one thought that would be conductive I suspect. Why would I want to test this stuff in the microwave? Remember that testing with an ohm meter is testing at DC. RF wise, it might be a different story. Regardless of matters of conductivity, insulators are cheap enough that they would be a better choice than repairing a broken insulator. I'd be very skeptical of the structural integrity of such a repair, especially if the break was not caused by impact. That would mean that the break was caused by structural stresses, and would likely recur. - 73 de Mike N3LI - |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Permeability of steel filled epoxy? | Homebrew | |||
epoxy instead of solder? | Homebrew | |||
FA: $9.99 3 VINTAGE CERAMIC DIPOLE INSULATORS-A SET>USA >AS NEW | Equipment | |||
FA: $9.99 3 VINTAGE CERAMIC DIPOLE INSULATORS-A SET>USA >AS NEW | Swap | |||
Is JB Weld Electrically conductive? | Homebrew |